Genie Universal Keypad Instructions

Keypad Overview

Program Key LED: Indicates programming status.

Keypad: Number pad for entering PIN and codes.

Up/Down Key (enter): Used to confirm entries and operate the opener.

LED On: Keypad LED is illuminated.

LED Flashing: Keypad LED is blinking.

Activate keypad by opening battery compartment and pull protective tab. Reinstall compartment door to begin programming.

It is recommended to complete programming before mounting keypad.

WARNING

MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.

• DO NOT install transmitter (keypad) unless the door operator's safety device works as required by the door operator's manual.
• Keypad must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.
• Keep people clear of opening while door is moving.
• DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly: Close door then disconnect opener using the manual release handle. DO NOT use transmitter or door operator. Refer to Door and Door Opener Owner's Manuals before attempting any repairs.

Keypad LED's

Successful Entries

Keypad LED will flash and beep ? each time a key is pressed and entry is accepted. The PROGRAM key and number pad back light will remain on for 15 seconds indicating a successful program or valid PIN has been entered. ?

Failed Entries

Keypad LED, PROGRAM key, and number pad back light will flash rapidly ? indicating a problem with programming or an invalid PIN entry. ?

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Important Features of This Keypad

• An audible beep will sound with every key pressed.
• Keypad will operate up to 3 doors with one PIN number.
• A temporary PIN can be set for convenient non-user access.
• Do not press the LEARN button for longer than the noted 2-3 seconds as it could cause the operational remotes to no longer work.

Compatibility

Below are the brands and specifications that this keypad is compatible with. Find the ID# in Chart A below that references your specific opener specification. You will need this number during programming. Refer to STEP 1 to find the type and/or LEARN/PROGRAM button.

DIP switch models are noted with an asterisk* - after STEP 2 in this instruction, please visit our website for instructions on models with these specifications: www.geniecompany.com/dipswitchesGUK

Chart A

Genie® and Intellicode® are registered trademarks of The Genie Company. All other listed names and trademarks are the property of their respective owners.

Programming Instructions

STEP 1: Find Specifications & Learn/Program Button

Locate the brand and opener/receiver specifications for the device by consulting the label on the opener/receiver, the instructions manual, the current remote controls for the opener, or the original manufacturer or the opener/receiver.

Find the LEARN/PROGRAM button on the device - shape, color or name of this button could vary by brand. For garage door openers, be sure to check under the light covers. For commercial openers, this button may be on the circuit board or the opener. In some cases, this button could also be on an external receiver that is mounted on or nearby the product. Consult the devices manual if needed.

STEP 2: Clearing the Keypad

Perform this task first before setting the PIN or at anytime the keypad needs to be reset to its factory default:

1. Remove activation tab from inside battery compartment.
2. Press both the PROGRAM & UP/DOWN keys at the same time and hold for 5 seconds. (tone will sound) - then release (green LED will flash and go out).
3. The keypad is now ready to be programmed. Start at STEP 3.

If the opener/receiver has dip switch technology, please move to the alternate instructions listed on our website at this time: www.geniecompany.com/dipswitchesGUK

DIP Switch Compatible Models Supplemental Instructions

This is a Universal Keypad supplemental instruction for dip switch compatible operators. Use this in place of Step 3 of the main instruction. Reference the main instruction for all other keypad features and functions.

What do fixed code dip switches look like and how to convert them for programming the Universal Keypad?

The DIP SWITCHES will be located on the garage door opener motor head or inside the remote control.

STEP 1: Find and notate DIP SWITCH positions

Each shaded box below represents a DIP switch position. In these boxes, write in the number 1, 2 or 3 as it corresponds to the +, 0, or - switch position shown on the remote, opener or receiver. You will need to reference this section in STEP 3 later. (Not all boxes will be used when working with 9 switch openers).

Convert the code for opener #1:

Convert the code for opener #2:

Convert the code for opener #3:

STEP 2: Find and notate opener ID#(s)

Below are the DIP switch model brands and specifications that this keypad is compatible with. Find the ID# in Chart B below that references the specific opener specification.

CHART B

All listed names and trademarks are the property of their respective owners.

Write ID#(s) Here.

You will need to reference this section in STEP 3 later.

STEP 3: PROGRAMMING TO ONE OR MORE OPENERS

This keypad can be programmed to up to 3 individual garage door openers in any combination of manufacturer specifications. Converted code(s) and opener ID#(s) from STEPS 1 & 2 are required to complete these steps.

Program Opener #1:

1. On the keypad, enter a personal PIN (3-8 digits).
2. On the keypad, press and release the UP/DOWN key (LED flashes slowly).
3. On the keypad, enter the ID# from CHART B.
4. On the keypad, press and release the UP/DOWN key (LED flashes quickly).
5. Enter the converted code from Step 1 on first page for opener 1.
6. On the keypad, press the UP/DOWN key once every two seconds until the door operates. Let it run until it stops.

Programming is complete for a single dip switch opener. To program additional dip switch openers at any time, see steps listed below.

Converted codes and ID#s for the additional openers are required to complete the next section.

Programming Multiple Openers:

Complete steps for Opener #1 above. To program Opener #2 or #3 at any time, follow the steps below with backlighting off. Be ready to reference the converted codes and ID#s from Steps 1 and 2 in this document.

1. On the keypad, press the PROGRAM button 2 times to program a second opener OR press it 3 times to program a third opener (LED flashes slowly).
2. On the keypad, enter ID# of opener from Chart B for Opener #2 or #3.
3. On the keypad, press and release the UP/DOWN key (LED flashes quickly).
4. Enter the converted code from Step 1 on first page for Opener #2 or #3.
5. On the keypad, press the UP/DOWN key once every two seconds until the door operates.

STEP 4: USING THE KEYPAD TO OPERATE OPENERS

Single Door Operation:

1. Ensure number pad back lighting is off.
2. Enter PIN and press the UP/DOWN key (opener operates).

Multi-Door Operation:

1. Ensure number pad back lighting is off.
2. Enter PIN and press the UP/DOWN key.
3. Press number key corresponding with desired opener (1, 2, or 3).
4. Desired opener will operate.

Additional Programming

SETTING A TEMPORARY MAIN PIN

If the keypad is to be used by normally unauthorized personnel (such as a repairman) a temporary PIN can be assigned to that personnel to gain access to the garage. This PIN will remain active until the main PIN is used again. (PRGM = PROGRAM).

1. Enter main PIN.
2. Press PRGM key three times (LED will turn solid indicating keypad is ready for temporary PIN).
3. Enter temporary PIN (3-8 digits).
4. Press PGRM key one time (LED will blink twice and go out indicating a temporary PIN is set).

To cancel the temporary PIN, operate the keypad/door with the original main PIN.

CHANGE PIN

If the main PIN needs changed, follow these steps.

1. Enter current main PIN.
2. Press PRGM key one time (LED will turn solid indicating keypad is ready for new PIN).
3. Enter new PIN (3-8 digits).
4. Press PGRM key one time (LED will blink twice and go out indicating a new PIN is set).

MOUNTING KEYPAD / REPLACING BATTERIES

Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above floor and clear of any moving door parts. NOTE that programming will not be lost during battery removal.

1. Remove battery cover and batteries. Replace if necessary. NOTE: Only use standard or alkaline AAA batteries. DO NOT use rechargeable batteries.
2. Drill a 3/32" pilot hole for the top mounting screw.
3. Install included screw into pilot hole, leaving 1/8" gap between the screw head and wall.
4. Hook the slotted mount on back of keypad over the screw.
5. Mark and drill a 3/32" pilot hole for the bottom screw and secure keypad to the wall. (Do not over-tighten).
6. Reinstall batteries.

Diagram Description: A screw is shown partially inserted into a wall. A gap of 1/8 inch is indicated between the screw head and the wall surface. This illustrates the recommended mounting method for the keypad, where the screw head provides a point to hang the keypad before marking the second screw hole.

References

For additional programming options and mounting instructions, refer to the main instruction sheet.

For questions, comments or troubleshooting, contact Customer Care by the phone number or web address listed on the main instruction sheet. You may also scan the QR code at the top of the main instruction sheet for additional information and links. ?