Project Source Refrigerator Water Filter
Model: H-1 / H-1-2
Item/Article #: 4873656 / 4083985
Introduction
Thank you for purchasing this Project Source Refrigerator Water Filter. These instructions are designed to ensure a simple installation process. For more detailed information, please visit Lowes.com, search the item number, and refer to the Guides & Documents tab on the product page.
If the item is no longer for sale, or if you have questions or problems, contact customer service at 1-866-389-8827 (8 a.m. - 8 p.m. EST, Monday - Sunday) or email partsplus@lowes.com. You can also visit www.lowespartsplus.com.
Troubleshooting
| Problem | Possible Cause | Corrective Action |
|---|---|---|
| Missing O-Ring | Manufacturer Error | Call Customer Service for replacement: 866-389-8827. |
| Leaking | Improper Installation | Remove and reinstall, ensuring the filter is securely installed within the refrigerator housing. |
| Slow Flow/No Flow | Improper Installation/Trapped Air Inside of the Filter | Submerge the filter (without its safety cap) in a bowl or sink full of water for 45 minutes to 1 hour, then reinstall. |
Care and Maintenance
Replace the filter every 6 months or after filtering 300 gallons (approximately 1135.62 liters), whichever comes first.
Warranty
This replacement filter cartridge is warranted to be free from defects in material and manufacture for one (1) year from the date of purchase. This warranty does not cover failures resulting from abuse, misuse, alteration, or damage not caused by the manufacturer, or failure to follow proper installation and use instructions. If the product fails to meet this warranty during the described period, the manufacturer will replace or refund the purchase price. This warranty does not cover additional costs such as labor.
Safety Information
WARNING: To reduce the risk of property damage due to water leakage, this filter MUST be installed in accordance with the manufacturer's specifications and instructions. Installation must comply with applicable state and local regulations. For cold water applications only. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. This filter unit must be replaced every 6 months, at the rated capacity, or sooner if reduced water flow occurs. Failure to follow instructions and operating specifications will void your warranty. The manufacturer assumes no responsibility or liability for damages arising out of misuse of the product. Protect from freezing.
Installation Overview
Step 1: Turn off water supply.
Locate the existing filter and remove it by turning the filter cartridge counter-clockwise a full 1/4 turn.
Step 2: Remove the filter.
To prevent water spillage on the filter tray, remove the filter by pulling it straight out.
Step 3: Prepare the filter tray.
Pull the filter tray out and empty out any water to prevent leaking from the cartridge housing. Reinstall the tray.
Step 4: Prepare the new filter.
Carefully remove the sanitary cap from the top of the new filter.
Step 5: Install the new filter.
Insert the new filter into the housing head and rotate the filter clockwise 1/4 turn or until it stops. Ensure the filter is fully installed in the refrigerator head a full 1/4 turn. Turn on the water supply. Note: Proper installation is required to activate the internal water valve. If the filter is not properly installed, you may experience slow flow or a chattering noise. If this occurs, uninstall and reinstall the filter, ensuring it is fully seated.
Step 6: Flush the system.
Run approximately 2.5 gallons (about 9.46 liters) of water from the dispenser periodically to clear the system and achieve good flow. If the water flow is slower than usual, repeat Step 5. Note: The initial flow rate may be slower than expected. Full flow rate should be restored within 24-36 hours.
Step 7: Inspect for leaks.
Inspect the filter for any noticeable leaks. If leaks are detected, please repeat Step 5.
Step 8: Reset the filter monitor light.
To reset the filter monitor light, refer to your refrigerator owner's manual for specific instructions.
Step 9: Use the replacement calendar.
Locate the included Water Filter Replacement Calendar and follow the instructions on the label to track filter replacement.
Specifications
| Parameter | Value |
|---|---|
| Flow Rate | 0.5 gpm (1.89 lpm) |
| Operating Temperature | 33°-100°F (0.6°-38°C) |
| Min Operating Pressure | 30 psi (207 kPa) |
| Max Operating Pressure | 100 psi (689 kPa) |
| Capacity | 6 months or 300 gallons (1,136 liters) |
Certifications
This filter (Model H-1/H-1-2) is Tested and Certified by NSF International against NSF/ANSI Standard 42 and 53 for the reduction of chlorine taste and odor, Tetrachlorethylene, Endrin, Carbon Tetrachloride, Trichlorobenzene, and p-Dichlorobenzene. Refer to the performance data sheet for a complete list of claims.
This filter is also Certified by IAPMO R&T against NSF/ANSI Standard 42, 53, 372, 401, P473 and CSA B483.1 for the reduction of chlorine taste and odor, lead, cyst, VOC's, mercury, asbestos, pharmaceuticals (such as Naproxen, Ibuprofen and Phenytoin), BPA, PFOA/PFOS. Refer to the Performance Data Sheet for a complete list of claims.
The compounds under NSF/ANSI 401 have been deemed as 'incidental contaminants / emerging compounds'.
