Introduction
Thank you for purchasing the DEWALT Magnetic Wireless Charger. This product allows for fast and convenient wireless charging with a secure magnetic connection and easy mounting for hands-free charging.
Package Contents
- 1 Magnetic Wireless Charger
- 2 Metal Slide-and-Lock Mounting Bracket
- 3 6ft DEWALT Type C with USB Adapter Charging Cable
- 4 3M mounting adhesive
- 5 Cable Wrap
- 6 User Manual
- 7 M4 Screws (4mm)
- 8 Drywall Anchors
Safety Guidelines
WARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT.
Definitions:
- DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
- WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
- CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
- NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
General Warnings:
- Read and understand all instructions. Failure to follow all instructions may result in electric shock, fire, and/or serious personal injury.
- Do not allow liquids to enter the magnetic wireless charger. This could cause electric shock.
- To reduce the risk of burns, use only the included cable and power adapter.
- Do not place other metal objects on the magnetic wireless charger.
- The magnetic wireless charger is designed only for charging MagSafe-compatible devices. Other uses may pose a risk of fire, electric shock, or electrocution.
- When cleaning, ensure the charger is unplugged. Wipe gently with a soft, dry cloth.
- Do not expose the charger to rain or snow.
- Use outdoors only in dry locations.
- Do not use if the charger has been dropped, impacted, or damaged.
- Do not disassemble the charger; there are no user-serviceable parts.
Charging Procedure
1. Insert the Type C end of the charging cable into the power source. If the power source has a USB port, place the USB adapter on the Type C connector before plugging into the USB port.
NOTE: For best results, a 20W or higher output charger is recommended.
2. Insert the Type C end of the charging cable into the port of the Magnetic Wireless Charger.
3. Align the Magnetic Wireless Charger with the charging coil on the back of your iPhone 12 series or newer.
NOTE: Only compatible with MagSafe cases. Remove non-MagSafe cases before charging.
Mounting Procedure
Using 3M Adhesive:
- Peel off the protective paper from one side of the adhesive sticker and firmly adhere it to the back of the wall-mount bracket.
- Peel off the protective paper from the second side of the adhesive sticker and adhere it firmly to the desired mounting location.
Using 4mm/M4 Screws:
- Screw the wall-mount bracket into the wall using two 4mm/M4 screws and drywall anchors.
NOTE: Charging can still take place from the mounted position.
Important Charging Notes
- For longest life and best performance, charge the device when the ambient air temperature is between 65°F and 75°F (18°–24°C). Do not charge in temperatures below +40°F (+4.5°C) or above +105°F (+40.5°C).
- The charger and device may become warm during charging; this is normal. To facilitate cooling after use, avoid placing the charger in a warm environment like a metal shed or uninsulated trailer.
- If the charger is not charging properly:
- Check the receptacle by plugging in a lamp or other appliance.
- Check if the receptacle is connected to a light switch that turns off power when the lights are turned off.
- Move the charging pad to a location where the ambient air temperature is approximately 65°F–75°F (18°–24°C).
- Keep conductive foreign materials (e.g., grinding dust, metal chips, steel wool, aluminum foil) away from the charger.
- Unplug the charger before cleaning.
- Do not freeze or immerse the charger in water or any other liquid.
Storage Recommendations
- Store in a cool, dry place away from direct sunlight and extreme temperatures.
- For long-term storage, a cool, dry place is recommended for optimal results.
FCC Compliance and RF Exposure
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by E-filliate Incorporated could void the user's authority to operate this device. The manufacturer is not responsible for radio or TV interference caused by unauthorized modifications.
RF Exposure Statement: This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.
Limited Lifetime Warranty and Customer Service
In case of product failure, E-filliate, Inc. will issue a replacement. DO NOT RETURN PRODUCT TO STORE. Instead, please call 888-480-9885, 8:00 a.m.–5:00 p.m. PT, Monday – Friday, or e-mail dewaltinfo@efilliate.com.
For customer service, if you have problems or questions about using this product, contact E-filliate, Inc. at 11321 White Rock Road, Rancho Cordova, CA 95742 USA. Provide the product number DXMA1902093 when contacting them.
