CUISINART G53501 Owner's Manual

Cuisinart® Gourmet 710

Models: 85-3108-6 (G53501) Propane, 85-3109-4 (G53502) Natural Gas

READ AND SAVE MANUAL FOR FUTURE REFERENCE.

Assemble your grill immediately. Missing or damaged parts should be claimed within 30 days of purchase.

For product inquiries, parts, warranty and troubleshooting support, please call 1-800-309-3452.

Visit: www.cuisinartbbqs.com

LIMITED 5-YEAR WARRANTY

IMPORTANT SAFETY INFORMATION

CAUTION: Sharp edges. Wear gloves when assembling your grill.

CAUTION: Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook.

INSTALLER OR ASSEMBLER/CONSUMER: This manual should be kept with the BBQ at all times.

WARNING: Failure to follow all of the Manufacturer's instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death.

Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try lighting this BBQ without reading the Lighting Instructions section of the Safety and Care Manual that accompanies this grill.

DANGER: If you smell Gas:

1. Shut off gas to the appliance
2. Extinguish any open flame
3. Open lid
4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department

DANGER: Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.

DANGER: An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

CAUTION: Avoid burns. The stainless steel and steel surfaces of this barbecue can become extremely hot, in direct sun and while the barbecue is in operation.

THIS BARBECUE IS FOR OUTDOOR USE ONLY

CUISINART® CUSTOMER CARE HOTLINE: 1-800-309-3452

HARDWARE PACK

Tools Needed for Assembly:

• #2 Phillips screwdriver (long and short)
• 1½" Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
• Rubber Mallet

For correct hardware assembly, always position the lock washer between the screw and the flat washer.

Note: Do not fully tighten all the nuts during this initial stage.

Caution: Sheet metal can cause injury. Wear gloves when installing this grill.

BEFORE ASSEMBLING THE BARBECUE, READ THESE INSTRUCTIONS CAREFULLY. Assemble the barbecue on a flat, clean surface. Grill is heavy. Two people are recommended to complete assembly.

PARTS LIST (PROPANE) FOR 85-3108-6 (G53501)

EXPLODED DIAGRAM (PROPANE) FOR 85-3108-6 (G53501)

(Diagram description: An exploded view of the Cuisinart G53501 grill, showing all parts with corresponding labels like AA, AB, BB, etc.)

PARTS LIST (NATURAL GAS) FOR 85-3109-4 (G53502)

EXPLODED DIAGRAM (NATURAL GAS) FOR 85-3109-4 (G53502)

(Diagram description: An exploded view of the Cuisinart G53502 grill, showing all parts with corresponding labels like AA, AB, BB, etc.)

ASSEMBLY INSTRUCTIONS

STEP 1: Wheels

Separate the 2 different types of wheels: 2 Locking Wheels (ED) and 2 Regular Wheels (EE).

Insert the U Pin (#12) into one of the regular Wheels (EE), as shown in image B. Attach the Regular Wheel (EE) to the front of the Bottom Shelf (EC), and use the U Pin (#12) to secure and tighten.

Repeat for remaining 3 Wheels (EE & ED).

NOTE: Regular Wheels (EE) need to be assembled to the front of the Bottom Shelf (EC), and Wheels with Lock (ED) need to be assembled to the back of the Bottom Shelf (EC), as shown in image A.

YOU WILL NEED:

• 12 (U Pin) x 1

STEP 2: Cart Side Panels and Back Panel

a. Ensure that the wheels are firmly locked in the “ON” position before continuing.

b. Assemble the Left Cart Side Panel (EA) and the Right Cart Side Panel (EB) to the Bottom Shelf (EC).

YOU WILL NEED:

• 2 (1/4-20UNCx16 Screw) x 6
• 5 (#7 Lock Washer) x 6
• 6 (#7 Washer) x 6

c. Assemble the Lower Back Panel (CP) to the Left Cart Side Panel (EA) and Right Cart Side Panel (EB).

TIP: The top of the lower back panel (CP) can be identified by the four recesses located on the top of this part.

YOU WILL NEED:

• 2 (1/4-20UNCx16 Screw) x 4
• 5 (#7 Lock Washer) x 4
• 6 (#7 Washer) x 4

STEP 3: Front Brace

Attach the Front Brace (CJ) to the Left and Right Cart Side Panels (EA and EB).

TIP: One person should align the left side, while the second person assembles the right side.

YOU WILL NEED:

• 1 (1/4-20UNCx38 Screw) x 2
• 5 (#7 Lock Washer) x 2
• 6 (#7 Washer) x 2

TIP: The bottom of the front brace (CJ) can be identified by the four recesses located on the bottom of this part.

STEP 4: Top Lid and Burner Box Assembly

THIS STEP REQUIRES 3 PEOPLE. DO NOT ATTEMPT ALONE. EXTREMELY HEAVY.

a. Position the Top Lid and Burner Box Assembly (A and B) onto Cart Assembly (C), as shown.

b. Assemble Burner Box Assembly (A and B) to the Left and Right Cart Side Panels (EA and EB), as shown.

YOU WILL NEED:

• 2 (1/4-20UNCx16 Screw) x 4
• 5 (#7 Lock Washer) x 4
• 6 (#7 Washer) x 4

c. Assemble the front of the Burner Box Assembly (A and B) to the Front Brace (CJ), as shown.

YOU WILL NEED:

• 1 (1/4-20UNCx38 Screw) x 2
• 5 (#7 Lock Washer) x 2
• 6 (#7 Washer) x 2

STEP 5: Upper Back Panel

Attach the Upper Back Panel (CL) to both the Left and Right Cart Side Panels (EA and EB).

Only install hardware in the bottom portion of the Upper Back Panel (CL), as shown in figure B.

DO NOT TIGHTEN SCREWS UNTIL SIDE SHELF HAS BEEN INSTALLED.

YOU WILL NEED:

• 1 (1/4-20UNCx38 Screw) x 2
• 5 (#7 Lock Washer) x 2
• 6 (#7 Washer) x 2

STEP 6: Left Side Shelf Assembly

a. Open the Lid. Assemble the Left Side Shelf Assembly (DH and DI) to the Cart Assembly by inserting the Side Shelf tabs into holes on the Cart Assembly (figure A).

b. Secure using hardware, as shown in figure B, C and D.

YOU WILL NEED:

• 2 (1/4-20UNCx16 Screw) x 2
• 5 (#7 Lock Washer) x 2
• 7 (Fiber Washer) x 2

YOU WILL NEED:

• 1 (1/4-20UNCx38 Screw) x 1
• 5 (#7 Lock Washer) x 1
• 6 (#7 Washer) x 1

YOU WILL NEED:

• 3 (NO.10-24UNCx13 Screw) x 3
• 8 (#5 Lock Washer) x 3
• 9 (#5 Washer) x 3

NOTE: Beware of sharp edges.

STEP 7: Electronic Ignition Assembly

a. Remove the Electronic Ignition Battery Cap (CE2) and the plastic nut from the Electronic Ignition Assembly (CE1).

b. Feed the Electronic Ignition Assembly (CE1) through the opening in the Left Side Shelf Fascia (DI) and secure using the nut.

c. Insert one “AA” battery into the battery compartment with the positive end facing outward, as shown. Secure using the Electronic Ignition Battery Cap (CE2).

d. Insert all Electrode wires (CF, DE) into the Electronic Ignition Assembly (CE1), as shown in figure E.

NOTE: All main burner and side burner electrode wire connection points are the same size.

STEP 8: Right Side Shelf Assembly

a. Open the lid. Assemble the Right Side Shelf Assembly (DA and DB) to the Cart Assembly by inserting the Side Shelf tabs into the holes on the Cart Assembly (figure A).

b. Secure using hardware, as shown in figure B, C and D.

YOU WILL NEED:

• 2 (1/4-20UNCx16 Screw) x 2
• 5 (#7 Lock Washer) x 2
• 7 (Fiber Washer) x 2

YOU WILL NEED:

• 1 (1/4-20UNCx38 Screw) x 1
• 5 (#7 Lock Washer) x 1
• 6 (#7 Washer) x 1

YOU WILL NEED:

• 3 (NO.10-24UNCx13 Screw) x 3
• 8 (#5 Lock Washer) x 3
• 9 (#5 Washer) x 3

NOTE: Beware of sharp edges.

STEP 9: Side Burner Assembly

a. Remove the hardware that is pre-assembled to the Side Burner Valve bracket (CC), as shown in figure A.

b. Insert the Side Burner Valve stem (CC) through the rear of the Right Side Shelf Fascia (DB). Assemble the Side Burner Valve (CC) to the Side Shelf Fascia (DB), using the hardware removed (figure A).

c. Assemble the Side Burner Control Knob (#11) to the Side Burner Valve (CC) (figure B).

YOU WILL NEED:

• 11 (Control Knob) x 1

d. Position the Side Burner (DD) through the opening in the Side Burner Drip Pan (DC).

NOTE: Make sure that the Side Burner (DD) engages the Side Burner Valve (CC), as shown in figure D.

e. Use the Side Burner Venturi Clip (#13), connect the Side Burner (DD) to the Side Burner Valve (CC).

YOU WILL NEED:

• 13 (Venturi Clip, Side Burner) x 1

f. Use the Wing Nut (#10) to assemble the Side Burner (DD) to the Side Burner Drip Pan (DC), as shown in figure F.

YOU WILL NEED:

• 10 (M4 Wing Nut) x 1

g. Attach the end of the Side Burner Electrode Wire (DE) to the underside of the Side Burner (DD), as shown in figure G. Ensure that the wire is pushed in firmly.

h. Place the Side Burner Cooking Grate (DG) into position on the Side Shelf (DA), as shown in figure H.

STEP 10: Heat Shield

a. Position the Heat Shield (CM) into the two hooks located on the bottom of the Upper Back Panel (CL), as shown in figure A.

b. Assemble the Heat Shield (CM) to the bottom of the Front Brace (CJ), as shown in figure B.

YOU WILL NEED:

• 4 (ST4.2X10 Tapping Screw) x 2

STEP 11: Grease Tray Tracks and Tray

a. Assemble the Left and Right Tracks (CN and CO) for the Grease Tray (CK), as shown in figure A-C.

b. Both the Left and Right Tracks (CN and CO) should be inserted into the two clips located on the Upper Back Panel (CL), as shown in figure B.

c. Assemble the front of the Left and Right Tracks (CN and CO) to the Front Brace (CJ), as shown in figure C.

YOU WILL NEED:

• 4 (ST4.2X10 Tapping Screw) x 2

d. Insert the Grease Tray (CK) into the opening of the Upper Back Panel (CL).

STEP 12: Door Handles

Assemble the Door Handle (EH) to the Left and Right Door Assembly (EF and EG) as shown in figure A.

YOU WILL NEED:

• 3 (NO.10-24UNCx13 Screw) x 4
• 8 (#5 Lock Washer) x 4
• 9 (#5 Washer) x 4

STEP 13: Door Assembly

a. Assemble the Right Door Assembly (EG), to the Bottom Shelf (EC) by inserting the fixed pin (bottom of door) into the hole provided (figure B).

b. Assemble the top of the Door Assembly (EG) to the Front Brace (CJ), by pressing in the door support pin and aligning with the hole located on the top right corner of the door.

TIP: Use a paint scraper to press-in the support pin, while the second person aligns the door. The support pin will lock into position when the door is assembled correctly.

c. Repeat steps a and b for the Left Door Assembly (EF).

STEP 14: Flame Tamers

Place the Flame Tamers (BD) into the Burner Box (BA).

STEP 15: Cooking Grates

a. Place the Cooking Grates (BE) into the Burner Box (BA), as shown.

STEP 16: Warming Rack

b. Assemble the Warming Rack (BF) by inserting the fixed pins into the warming rack support bars located on the Burner Box (BA), as shown in figure A and B.

STEP 17: Propane Tank Installation

FOR PROPANE MODELS ONLY.

For natural gas model, follow step 18.

a. Position the Regulator Hose (CB) through the hole in the Right Side Panel (EB).

b. Position the 20 lb propane tank onto the Bottom Shelf (EC), and secure using the Bolt (F4) (already attached) located on the underside of the Bottom Shelf, as shown in figure B.

c. Attach the regulator coupling nut to the LP cylinder valve. Be careful not to cross thread. Hand tighten only.

d. Perform Leak Test. See page 5 of the Cuisinart® Safety and Care Manual.

ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the Cuisinart® Safety & Care Manual. All Safety and Leak Test MUST BE PERFORMED BY THE END USER, prior to lighting this BBQ.

WARNING: Do not store extra propane tanks within BBQ cart.

STEP 18: Natural Gas Connection

FOR NATURAL GAS MODEL ONLY.

a. Attach the Natural Gas Hose (CB) to the Side Burner Valve (CC) as shown.

b. Perform Leak Test. See page 6 of the Cuisinart® Safety and Care Manual.

ATTENTION: In order to complete installation of your Natural Gas BBQ a 1/2" or 3/8" adapter may be required to connect your BBQ's Natural Gas hose to your home gas supply. Contact your Natural Gas supplier to purchase the necessary part.

ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the Cuisinart® Safety & Care Manual. All Safety and Leak Test MUST BE PERFORMED BY THE END USER, prior to lighting this BBQ.