Introduction
This document provides comprehensive instructions for the installation of the Philips Flareon outdoor wall light, model number 9290033619. It details the necessary tools, components, and step-by-step procedures to ensure a safe and correct installation.
Package Contents and Required Tools
Included Items:
- A: Main light fixture assembly
- B: Mounting hardware and instruction booklet
Excluded Items (Tools Required for Installation):
- [Drill] with appropriate drill bit size (e.g., ⌀4 mm) ड्रिल
- [Phillips Screwdriver] ?
- [Flathead Screwdriver] ?
- [Pencil] for marking ✏️
- Wall plugs and screws (ensure suitability for your wall type) ?
- Light bulb (E27 base, maximum 25W) ?
Safety Information
Important: Before commencing any installation work, ensure the main power supply is switched OFF at the circuit breaker. ⚠️
This fixture is rated IP44, indicating protection against solid objects larger than 1mm and splashing water from any direction, making it suitable for outdoor environments.
Electrical installations must be performed by a qualified person to ensure compliance with local regulations and safety standards. Always ensure proper grounding for electrical safety. ?
Use only an E27 base light bulb with a maximum wattage of 25W. ?
Installation Steps
Step 1: Prepare and Assemble Fixture Components
Ensure the power is OFF at the main circuit breaker. [Power OFF] ⚠️
Begin by assembling the main parts of the light fixture. This typically involves connecting the cylindrical shade to the base assembly.
- 1. Rotate the top part of the fixture (shade) to align with the base. ?
- 2. Secure the shade to the base using the provided screws. ?
- 3. Attach the mounting bracket to the fixture base if it is not pre-assembled.
- 4. Connect any internal wiring within the fixture assembly if required.
- 5. Ensure all internal wire connections are secure. ?
Step 2: Mark and Drill Mounting Holes
Hold the mounting bracket against the wall at the desired installation location. Use a pencil to mark the precise positions for the mounting screws. ✏️
Drill holes at the marked locations. The diagram suggests using a drill bit of approximately ⌀4 mm. ड्रिल
Step 3: Mount the Backplate
If necessary, insert appropriate wall plugs into the drilled holes to ensure a secure mounting. ?
Align the mounting bracket with the holes (or wall plugs) and secure it firmly to the wall using screws. The diagram indicates "UP1" to show the correct orientation for mounting.
Step 4: Connect Electrical Wiring
Carefully feed the electrical supply cable through the designated entry point on the mounting bracket.
Connect the wires from the mains supply to the corresponding terminals on the fixture:
- Connect the Neutral (N) wire to the terminal marked 'N'.
- Connect the Live (L) wire to the terminal marked 'L'.
- Connect the Earth/Ground (?) wire to the grounding terminal.
Verify that all wire connections are tight and secure. ?
Step 5: Attach the Fixture to the Wall
Align the main fixture body with the mounted backplate. Secure the fixture to the bracket using the provided screws. ?
Step 6: Install Bulb and Finalize Installation
Screw in the E27 light bulb, ensuring it does not exceed the 25W maximum. ?
Attach the outer shade or cover to the fixture, securing it as per the design. ?
Once installation is complete, restore power at the main circuit breaker. [Power ON] ?
Technical Details
- Bulb Type: E27
- Maximum Wattage: 25W
- Ingress Protection Rating: IP44
- Product Name: Flareon
- Brand: Philips
- Model Number: 9290033619
Manufacturer Information
Signify Commercial UK Limited
Unit 3, Guildford Business Park, Guildford, Surrey, GU2 8XG, UK
Signify
I.B.R.S. / C.C.R.I. Numéro 10461, 5600 VB Eindhoven, the Netherlands
Customer Service Contact: 00800-74454775
For more information, visit: www.philips.com/lighting
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
© 2023 Signify Holding
