i-PRO WV-S15500 Series Camera Installation Procedure

Parts and Functions

Model Numbers: WV-S15500-V3L, WV-S15500-V3LN, WV-S15700-V2L

Key Components:

• Name Plate
• Front Part (External: Sunshade, Internal: Main Case)
• Adapter Box
• MicroSD Card Slot
• Indicators/Buttons: WIDE+AF button, TELE+AF button, SD ON/OFF button, INITIAL SET button
• ACT Indicator (green)
• LINK ACT Indicator (orange)
• SD MOUNT Indicator
• YAW lock screw, TILT lock screw, PAN lock screw
• Grommet cover
• Cable access hole (Ø27 mm / Ø1-1/16 inches)
• RJ45 cap
• Grommet (accessory)
• I/O Cable (WV-QCA501A: optional accessory)
• Waterproof tape (WV-QCA501A accessory)

Installation Methods:

• For mounting on ceiling
• For mounting on wall
• For upwards facing installations

Installation Procedure

Step 1: Preparations

Ensure the microSD card is inserted correctly. A click sound indicates proper insertion. Format the microSD memory card using the camera's operating instructions.

Mounting Preparation:

• Attach the adapter box to the camera.
• Secure the camera using the YAW, TILT, and PAN lock screws.

Step 2: Mounting the Camera

Refer to the diagrams for specific mounting configurations on ceilings or walls. Ensure proper alignment and secure all screws.

Step 3: Cable Connections

Ethernet Connection:

• Use Category 5e or better, straight, 4-pair (8-pin) Ethernet cable.
• Maximum cable length: 100 m (328 feet).
• Connect the RJ45 connector to the camera.

I/O Cable Connections (Optional Accessory WV-QCA501A):

• Connect Audio In (White), Audio Out (Black), and EXT I/O terminals.
• Ensure the GND line is properly connected.
• Minimum pull-out strength for cables: 724 N (163 lbf) per piece.

Power Connection:

• The camera supports 12 V DC or PoE (Power over Ethernet).

Step 4: Securing Cables and Housing

Step 4-1:

• Use the grommet cover (accessory) to protect cable entry points.
• Apply waterproof tape (WV-QCA501A accessory) by stretching it to approximately twice its length for a secure seal.

Step 4-2:

• Mount the adapter box using the provided mounting pins (accessory).
• Ensure all cables are neatly routed and secured within the housing.

Step 5: Connecting I/O and Network Cables

Connect the I/O cable and LAN cable to their respective ports within the adapter box.

Step 6: Closing the Housing

Securely close the adapter box, ensuring the grommet covers are properly fitted.

Step 7: Attaching the Camera Body

Mount the camera body onto the adapter box. Ensure the WIDE+AF and TELE+AF buttons are accessible.

Step 8: Power On

Turn on the power supply (12 V DC or PoE).

Step 9: Adjustments and Lock

Adjust the camera's YAW, TILT, and PAN angles as needed. Tighten the corresponding lock screws with the specified torque:

• PAN lock screw: 2.7 N-m (1.99 lbf·ft)
• TILT lock screw: 4.3 N-m (3.17 lbf·ft)
• YAW lock screw: 2.7 N-m (1.99 lbf·ft)

Image Rotation: If image rotation is required, refer to the technical information website for instructions on rotating the sunshade.

Step 10: Network Configuration

Connect a laptop to the network and use the IP Setting Software (Control No.: C0123) or i-PRO Configuration Tool (ICT) (Control No.: C0133) to configure the camera's network settings.

Additional Information:

• Refer to the technical information website for details on "Extra optical zoom" (Control No.: C0124) and "How to take a wide depth of field" (Control No.: C0127).