Manuals+

myQ Wireless Control Panel

MODELS: L956W & CH125

Product Manual

For more information, please visit www.devancocanada.com or call toll free at 1-855-931-3334

Overview

Your Wireless Control Panel is compatible with Security+ 3.0™ garage door openers. All Security+ 3.0 garage door openers have a white learn button. The Wireless Control Panel can be used as a secondary device to open and close your garage door, and to turn on and off your garage door opener lights. The images throughout this manual are for reference only and your product may look different.

⚠️ WARNING

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

  • Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
  • NEVER permit children to operate or play with door control push buttons or remote control transmitters.
  • Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
  • ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
  • Unattended devices and features are to be used ONLY with sectional doors.

⚠️ WARNING

This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Installation

Install the control panel within sight of the garage door at a minimum height of 5 feet (1.5m) where small children cannot reach, and away from moving parts of the door.

Tools Required

Diagram shows a hammer, a Phillips head screwdriver, and a drill with a 5/32 inch drill bit.

Hardware Included

Diagram shows a screw labeled "6ABx1-1/4"" and a plastic anchor.

Mount the Control Panel

  1. Mark the location of the bottom mounting hole and drill a 5/32 inch (4 mm) hole.
  2. Tap in anchor with hammer if installing on drywall. Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall.
  3. Position the bottom hole of the control panel over the screw (a) and slide down into place (b).
  4. Lift up the control panel push bar and mark the top hole.

Installation (continued)

  1. Remove the control panel from the wall and drill a 5/32 inch (4 mm) hole for the top screw. Tap in anchor with hammer if installing on drywall.
  2. Position the bottom hole of the control panel over the screw and slide down into place. Install the top screw and close the push bar.

Programming the Control Panel to Your Garage Door Opener

Choose an option below to program the wireless door control.

Option 1:

Follow the instructions below for your door control panel model to set your garage door opener into programming mode.

RECOMMENDATION: Have your door control panel product manual available, as models vary in how to set the garage door opener into programming mode.

Control Panel

Lift the push bar. Press the [Learn Button] [x2]. After the second press, the LED on the door control panel will pulse repeatedly.

Push Button Door Control

Press and hold the [Light Button], then press and release the [Push Button]. The button LED will begin to flash.

Smart Control Panel

  1. Select [Menu].
  2. Scroll down and select [Program].
  3. Scroll down and select [Remote].

Option 2:

Locate the LEARN button on your garage door opener (a ladder may be required). Press and immediately release the [Learn Button]. The [Learn Button] LED will turn on solid.

Programming the Control Panel to Your Garage Door Opener (continued)

  1. Within 30 seconds, press and hold the control panel [Push Button] until the garage door opener lights flash and/or two [Click]s are heard.

TEST FOR SUCCESS: Press the control panel [Push Button]. The garage door opener will activate. Next, press the control panel [Light Button]. The garage door opener lights should turn on or off. If the garage door does not activate, and/or the garage door opener lights do not turn on or off, repeat the programming steps.

NOTE: The wireless control panel will continue to activate the garage door opener if a wired control panel has been placed into Lock mode.

Features and Operation

Features

Diagram shows the control panel with labels for [Push Bar], [Command LED (Amber)], [Light Button], and [Learn Button].

Operation

Push Bar

Press [Push Bar] to open / close the garage door. When the [Push Bar] is pressed, the LED behind the [Push Bar] will blink when transmitting a signal. To conserve battery power, the LED will turn off when not in use. If the LED does not light when the [Push Bar] is pressed, the battery power is low. Replace the battery (see page 10 for instructions).

Light Button

Press the [Light Button] to turn the garage door opener lights on or off. When the lights are turned on they will stay on until the [Light Button] is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after a specified period of time (the factory setting is 4 1/2 minutes). The [Light Button] will not control the lights when the door is in motion.

NOTE: Connect your garage door opener to the myQ app to manage the length of time the light stays on.

Program a Remote Control or Wireless Keypad to Your Garage Door Opener

  1. Lift the push bar. Press the [Learn Button] twice (after the second press, the LED on the door control panel will pulse repeatedly).

  2. 02a

    Within 30 seconds, press and hold the button on the remote control that you wish to use. Release the button when the garage door opener lights flash and/or two [Click]s are heard.

  3. 02b

    Within 30 seconds, enter a 4-8 digit personal identification number (PIN) of your choice. Press and hold the [Home Button] until the garage door opener lights flash and/or two [Click]s are heard.

TEST FOR SUCCESS: Press the remote button you programmed. The garage door opener will activate. If the garage door does not activate, repeat the programming steps.

TEST FOR SUCCESS: With the garage door closed, enter the PIN you programmed and press the [Home Button]. The garage door opener will open the door. If the garage door does not open, repeat the programming steps.

To Erase All Codes from Garage Door Opener Memory (Remote Controls, Wireless Keypads, and Wireless Control Panel)

To deactivate the accessories, first erase all codes: Press and hold the “Learn” button on the garage door opener until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote control, wireless keypad, or wireless control panel you wish to use.

Replacing the Battery

If the LED on your wireless control panel does not flash when the [Push Bar] is pressed, the battery power is low and it needs to be replaced. Replace the battery with only 3V CR2032 coin cell battery. Dispose of the old battery properly. To replace battery, follow the instructions as shown below:

  1. First, remove the control panel from the wall by unscrewing the top mounting screw (a). Lift the control panel up and pull off the wall (b).
  2. On the back side of the control panel, using a Phillips #2 screwdriver, unscrew the screw, holding the logic board in place. The screw should remain attached to the logic board.
  3. Remove the logic board from the control panel. (a) Pull the top of the logic board away from the control panel. (b) Slide the logic board up out of the lower screw housing. (c) Pull the logic board away from the control panel.
  4. With a cotton swab, push the old battery out of its holder.

Replacing the Battery (continued)

  1. Insert the replacement battery positive side up and ensure it is centered with the strap.
  2. Replace the logic board onto the backside of the control panel. Slide the logic board under the lower screw housing. Then align the guiding hole in the board to the control panel. The logic board should not move once secure in the control panel.
  3. Use a Phillips #2 screwdriver to attach the logic board to the control panel with the screw.
  4. Position the bottom hole of the control panel over the screw and slide down into place. Install the top screw and close the push bar.

⚠️ WARNING

INGESTION HAZARD: This product contains a button cell or coin battery.

DEATH or serious injury can occur if ingested.

A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.

KEEP new and used batteries OUT OF REACH of CHILDREN.

Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

⚠️ WARNING

Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.

Even used batteries may cause severe injury or death.

Call a local poison control center for treatment information.

Battery Type: CR2032

Battery Voltage: 3 V

Non-rechargeable batteries are not to be recharged.

Do not force discharge, recharge, disassemble, heat above (manufacturer's specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.

Ensure the batteries are installed correctly according to polarity (+ and -).

Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.

Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.

Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Additional Resources

One Year Limited Warranty

The Chamberlain Group LLC ("Seller") warrants to the first consumer purchaser of this product that it is free from defect in materials and/or worksmanship for a period of 1 year from the date of purchase. For more information, visit www.myq.com/warranty

Contact Us

For additional information or assistance, please visit: support.chamberlaingroup.com

NOTICE: This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

How to Order Repair Parts

DEVANCO CANADA
19192 HAY ROAD, UNIT Q
SUMMERSTOWN, ON, KOC 2E0
TOLL FREE 1-855-931-3334
WWW.DEVANCOCANADA.COM

WHEN ORDERING REPAIR PARTS PLEASE SUPPLY THE FOLLOWING INFORMATION:

114-6096-000

©2025 The Chamberlain Group LLC

myQ and the myQ logo are trademarks, service marks, and/or registered trademarks of The Chamberlain Group LLC. All other trademarks, service marks and product names used herein are the property of their respective owners. The Chamberlain Group LLC. 300 Windsor Drive, Oak Brook, IL, 60523, United States

See chamberlain.com/patents

Models: L956W, L956W Wireless Control Panel, Wireless Control Panel, Control Panel

File Info : application/pdf, 13 Pages, 3.80MB

PDF preview unavailable. Download the PDF instead.

Installation Manual L956W

References

Adobe PDF Library 17.0

Related Documents

Preview myQ Wireless Keypad Product Manual - Models L979M, CH348, CH348C
This product manual provides comprehensive instructions for the myQ Wireless Keypad, including setup, programming for various garage door opener models, key features, battery replacement, and troubleshooting. Compatible with Chamberlain, LiftMaster, and Craftsman openers.
Preview myQ 1-Button Remote Control CH361 Product Manual
This manual provides instructions for programming and using the myQ 1-Button Remote Control (Model CH361) with compatible garage door openers. It covers setup via the myQ app and using the learn button, as well as battery replacement and warranty information.
Preview myQ Garage Door Remote Control Product Manual
This product manual provides instructions for programming and using myQ 1-button and 3-button garage door remote controls (Models L991S, CH161, L993S, CH163, Q163LA). It covers programming via the myQ app or the learn button, battery replacement, and warranty information.
Preview myQ CH361 1-Button Remote Control Product Manual
Comprehensive product manual for the myQ CH361 1-Button Remote Control, detailing programming instructions via the myQ app and learn button methods, battery replacement, and warranty information from Chamberlain Group LLC.
Preview myQ 1-Button Remote Control CH361 Product Manual
This manual provides instructions for programming and using the myQ 1-Button Remote Control, model CH361. It covers compatibility, safety warnings, programming steps for various garage door opener learn button colors (white, yellow, purple/brown, orange, red), and battery replacement.
Preview myQ Wireless Keypad Product Manual and Installation Guide
Comprehensive guide for the myQ Wireless Keypad, covering programming, installation, features, and battery replacement for models L979M, CH348, and CH348C. Learn how to connect to your garage door opener and use features like One Button Close and temporary PINs.
Preview myQ Smart Garage Video Keypad User Guide: Setup, Features, and Safety
Detailed user guide for the myQ Smart Garage Video Keypad (VKP1-MYQ, VKP1-LM, VKP1-RJO). Learn how to install, set up, use features like video storage, and understand safety warnings.
Preview myQ Smart Garage Control FAQs: Your Questions Answered
Find answers to frequently asked questions about the myQ Smart Garage Control, covering compatibility, setup, troubleshooting, and smart home integrations for your garage door opener.