PRODUCT FEATURES
- Hands-free infrared sensor-operated gear actuator with chrome plated metal housing
- Angled Sensor delivers reliable flush even with toilet seat in raised position
- Self-cleaning brass piston with integral wiper spring prevents clogging and valve run-on
- Electronic courtesy flush button
- Optional Sanitary Flush: Automatic flush after 24 hours of non-use
- Object Detection Indicator: LED blinks when user or object is detected
- User in View Indicator: Green LED flashes 3 times after user is detected for 5 seconds
- Low Battery Indicator: Yellow LED flashes when batteries need to be replaced
- Easy Battery Replacement: Water does not need to be shut off to change batteries
- Chloramine-resistant EPDM seals
- No external volume adjustment
- Can be installed left or right handed
- Installation tools included
MODEL NUMBERS
- 6047SM.111: Manual Flush Valve with Side-Mount Operator for 1-1/2" flushometer bowl, 1.1 gpf/4.2 Lpf
- 6047SM.121: Manual Flush Valve with Side-Mount Operator for 1-1/2" flushometer bowl, 1.28 gpf/4.8 Lpf
- 6047SM.161: Manual Flush Valve with Side-Mount Operator for 1-1/2" flushometer bowl, 1.6 gpf/6.0 Lpf
SPECIFICATIONS
OPERATING PRESSURE: 25 psi (flowing)-80 psi (static)
FLOW REQUIREMENT: 25 gpm (94.6 L/min.)
BATTERY LIFE: 100,000 flushes (3+ years @ 3,000 flushes per month) (4) "C" alkaline batteries included
ADJUSTABLE RANGE: 8" to 48" (32" default)
INDICATORS
User In View Indicator: Green LED flashes 3 times after user is detected for 5 seconds
Low Battery Indicator: Yellow LED flashes when batteries need to be replaced
Object Detection Indicator: LED blinks when user or object is detected
Courtesy Flush Button
TYPICAL WATER CLOSET INSTALLATION
Diagram showing the flush valve installed on a toilet. It illustrates the connection to the finished wall, supply line (1" IPS), and the critical level (C-L) relative to the fixture. Key measurements include: 73 mm (2-7/8") from the finished wall to the valve center, 343 mm (13-1/2") height from the finished floor to the critical level, and a rough-in dimension of 295 mm (11-1/2"). The supply connection is DN 25 mm (1" I.P.S.). The diagram also shows the critical level line and indicates that rough-in details are on the back.
RECOMMENDED SPECIFICATION
Toilet flush valve includes sensor-operated gear actuator with metal casing. Brass valve body and cover with chrome finish. Features self-cleaning brass piston valve with integral wiper spring in bypass orifice to prevent clogging. Valve closes and does not need to be reset after loss of water pressure. Includes sweat solder kit with wall flange and cover tube. Vacuum breaker and angle stop with vandal resistant cap and back-flow protection included.
LISTINGS
- ASSE 1037
- ANSI/ASME A112.19.2
- ADA Compliant
INCLUDES
- 1" I.P.S. angle stop with back-flow prevention and vandal-resistant cap
- Sweat solder kit including cover tube and wall flange
- High back pressure vacuum breaker with down tube
- Spud coupling & flange for 1-1/2" top spud
ROUGHING-IN DIMENSIONS
Diagrams illustrating the required dimensions for installing the flush valve. These include measurements from the finished wall for the valve body and supply connection, as well as the overall rough-in dimension for the fixture. Key measurements shown are: 147 mm (5-13/16") from the finished wall to the center of the supply, 108 mm-133 mm (4-1/4" to 5-1/4") for the rough-in dimension, and 38 mm-127 mm (1-1/2"-5") from the finished wall to the critical level. The main valve body height is 253 mm (9-15/16") from the rough-in line, with a minimum critical level of 152 mm (6") above the fixture.
INSTALLATION
Installation Left or Right
Diagrams showing the flush valve assembly configured for either left-hand or right-hand installation.
Meets the Americans with Disabilities Act Guidelines and ANSI A117.1 Requirements for Accessible and Usable Building Facilities - Check Local Codes.
