V-TAC T8 LED Tubes
Instruction Manual
WEEE Number: 80133970
Introduction & Warranty
Thank you for selecting and buying a V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any further queries, please contact your dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best.
The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.
The LED tube can be used in hotels, offices, factories, conference rooms, meeting rooms, commercial complexes, residential buildings, schools, colleges, universities, hospitals, etc.
Warnings
- Installation should only be done by a certified electrician.
- Operation environment temperature: from -20°C to +45°C.
- Do not use DC electricity.
- Do not modify the fitting to be used with the LED Tube.
- V-TAC LED Tubes are NOT designed to be used in emergency operations.
- For Indoor use only.
- Do NOT use with electronic ballasts. V-TAC LED tubes are not compatible with electronic ballast circuits. In order to use the electronic ballast fitting, you must ensure to remove the electronic ballast from the fitting and rewire the circuit as per new fitting installation as shown below. Ensure the installation and wiring is carried out by a certified electrician.
Technical Data
| MODEL | VT-6072 | VT-9077 | VT-1277 | VT-1577 |
|---|---|---|---|---|
| SKU | 216392,216393,216394 | 216262,216272 | 216263,216273,216264 | 216265,216309,216310 |
| WATTS | 9W | 14W | 18W | 20W |
| LUMENS | 850LM@Sphere360° | 1400LM@Sphere360° | 1850LM@Sphere360° | 2100LM@Sphere360° |
| DF | >0.5 | >0.7 | >0.7 | >0.7 |
| CRI | >80 | >80 | >80 | >80 |
| BEAM ANGLE | 160° | 160° | 160° | 160° |
| BODY TYPE | Plastic | Plastic | Plastic | Plastic |
| IP RATING | IP20 | IP20 | IP20 | IP20 |
| HOLDER | G13 | G13 | G13 | G13 |
| ON/OFF CYCLE | >15,000 Times | >15,000 Times | >15,000 Times | >15,000 Times |
| LIFE SPAN | 25,000 Hours | 25,000 Hours | 25,000 Hours | 25,000 Hours |
| DIMENSION | 28x600mm | 28x900mm | 28x1200mm | 28x1500mm |
| INPUT VOLTAGE | AC: 220-240V,50Hz | AC: 220-240V,50Hz | AC: 220-240V,50Hz | AC: 220-240V,50Hz |
New Fitting Installation
Installation should only be done by a certified electrician.
- Switch Off the power.
- Ensure the wiring diagram is followed as highlighted.
- Insert V-TAC LED Tube.
- Switch On the power to test the light.
Wiring Diagram
A diagram shows a connection for a new fitting. It illustrates AC 220-240V, 50Hz input, with V-TAC INPUT connected to one side of the LED TUBE. The diagram indicates 'Single Side Power Only'.
Installation & Replacement of Fluorescent Lamp (Single Magnetic Ballast Circuit)
Installation should only be done by a certified electrician.
Please refer to the wiring diagram for replacing a fluorescent tube on a single magnetic ballast circuit with a V-TAC LED Tube.
Wiring Diagram
A diagram shows a connection for replacing a fluorescent lamp with a V-TAC LED Tube on a single magnetic ballast circuit. It includes AC 220-240V, 50Hz input, V-TAC INPUT, LED Starter, LED TUBE, and Inductance Ballast.
Installation Steps
- Switch off the power. [Power switch icon]
- Remove the existing fluorescent lamp. [Icon showing removal of a fluorescent tube]
- Remove the existing fluorescent starter. [Icon showing removal of a starter]
- Insert LED T8 starter. [Icon showing insertion of an LED starter]
- Insert V-TAC LED Tube. [Icon showing insertion of an LED tube]
- Switch ON the power. [Power switch icon]
Packing
- LED Tube (1 PC)
- Instruction Manual (1 PC)
- Dummy Starter (1 PC)
Disposal Information
This marking indicates that this product should not be disposed of with other household wastes. [Symbol of a crossed-out wheeled bin]
Caution, risk of electric shock. [Symbol of a lightning bolt within a triangle]
WEEE (Waste Electrical and Electronic Equipment) must be returned to designated collection points by users at the end of their life. This return is free of charge. Owners of WEEE are obliged to remove lamps from the WEEE before returning them to the collection point. Disposal of electrical equipment in landfills or dumps can lead to pollutants entering groundwater and entering the food chain, harming health and well-being.
Find collection and return points online: https://www.ear-system.de/ear-verzeichnis/sammel-und-ruecknahmestellen
Contact Information
For any query/issue with the product, please reach out to us at: SUPPORT@V-TAC.EU
For more products range, inquiry please contact our distributor or nearest dealers.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
ear-system.de/ear-verzeichnis/sammel-und-ruecknahmestellen
