USER MANUAL

Button function

Left Button

• Short Press: Mark a new lap
• Hold for 2 seconds: Power off (⚫)
• (Power on: short press the button)
• (Short press in setting mode: exit / return and save the setting) (↩️)

Mid Button

• Short Press: Pause / Continue (⏸️) (Short press to start recording after power on)
• Hold for 2 seconds: save the exercise record and exit the exercise
• (Short press in setting mode: enter the current setting / switch the number of digits)

Right Button

• Short Press: Page turning (➡️)
• Hold for 2 seconds: setting mode (⚙️)
• (Short press in setting mode: switch setting options / switch the numerical)

Status Icons

Standard accessories

• Main Device x 1
• Charging Cable x 1
• User Manual x 1
• Standard bike mount x 1
• Rubber pad for standard bike mount x 1
• Big size rubber ring x 2
• Small size rubber ring x 2

How to Install

Standard Mount Installation

Steps:

1. Install the rubber pad onto the mount.
2. Tie the mount onto the bar with the rubber rings.
3. Tie up the mount.
4. Install the main device onto the mount.
5. Rotate the main device for 90 degrees.
6. Installation completed.

Charging

1. Please charge the device before first time use.
2. Please use DC 5V power adaptor for charging.
3. During the charging, the battery icon will flash until fully charged.

Open the rubber cover, connect the device with usb cable to charge.

The product has a built-in battery. Do not throw the product into a fire. Please choose an adapter that meets the rated voltage of the device to charge the device to avoid damage to the device.

Acquiring Satellite Signals, Time Setting and Auto Backlight

Auto Backlight

This device will automatically calculate the sun rise and sun set time (☀️). From half an hour before sunset to half an hour after sunrise, the backlight will automatically lighten up. In the rest of the time, the backlight will be turned off if no operation is detected in 15 seconds.

Acquiring Satellite Signals

Please make sure the device is outdoor and under a clear view of sky. Usually it may take 15~90 seconds to locate satellite signals. Remain stationary when acquiring satellite signals. This device can use a speed sensor or GPS for speed tracking. When the speed sensor is not connected, the device will use GPS for speed tracking, and will use the speed sensor when the sensor is connected.

Time Setting

The time and date will be calibrated automatically after locating satellite signals when the device is powered on (Please set the time zone correctly, refer to the time zone setting chapter) or connect the device to the App (CoospoRide) to sync the time.

Connecting with ANT+ Sensors

1. First, please make sure that sensors are in wake-up mode.

Wear on correctly to wake up the heart rate monitor (❤️).

The speed sensor, cadence sensor (⚙️), and power meter are awakened by turning the pedals or wheels.

(Note: Additional purchase required for heart rate monitor, speed sensor, cadence sensor and power meter.)

ANT+ Peripheral Connection

1. Hold the ➡️ button to get into setting mode.
2. There are 5 settings pages available (P1~P5), press the ➡️ to switch to P1.
3. Press ⏸️ to select to enter.
4. The computer automatically searches for ANT+ peripherals and connects after searching.
5. Press ⚙️ to save the found accessories and return. If no ANT+ accessory is found, the device will return to the last pages automatically. (When a power device is connected during riding, the computer will display power data first; when there is no power device, it will display GRA slope data).

Hold the ➡️ button to enter setting mode. Press ➡️ to switch between P1-P5. Press ⏸️ to select/enter.

Save and get back to the last pages (if no device found in 20 seconds, the device will get back to the last pages automatically).

Setting the Wheel Size

1. Hold the ➡️ button to get into setting mode.
2. There are 5 settings pages available (P1 ~ P5), press the ➡️ to switch to P2.
3. Press ⏸️ to select to enter.
4. Press ⏸️ to select the setting digit; press the ➡️ to set the numbers.
5. Press ⚙️ to save and exit (Automatically exit in 6 seconds if no operation detected).

Press ➡️ to switch pages. Press ⏸️ to select digit. Press ➡️ to set number.

Save and get back (Automatically exit if no operation detected in 6 seconds). The selected digit will flash.

Common Wheel Size and Circumference

Wheel Size L (mm)

Time Zone Setting

1. Hold the ➡️ button to get into setting mode.
2. There are 5 settings pages available (P1 ~ P5), press the ➡️ to switch to P3.
3. Press ⏸️ to select to enter (Default time zone: UTC/GMT + 08:00).
4. Press ⏸️ to select the setting digit, press the ➡️ to set the numbers.
5. Press ⚙️ to save and exit (Automatically exit in 6 seconds if no operation detected).

Press ➡️ to switch pages. Press ⏸️ to select digit. Press ➡️ to set number.

Save and get back (Automatically exit if no operation detected in 6 seconds). The selected digit will flash.

Setting Metric and Imperial Units

1. Hold the ➡️ button to get into setting mode.
2. There are 5 settings pages available (P1 ~ P5), press the ➡️ to switch to P4.
3. Press ⏸️ to enter (Default: KMH).
4. Press the ➡️ to switch.
5. Press ⚙️ to save and exit (Automatically exit in 6 seconds if no operation detected).

Press ➡️ to switch pages. Press ➡️ to set KMH/MPH.

Save and get back (Automatically exit if no operation detected in 6 seconds).

Power Calibration

1. Hold the ➡️ button to get into setting mode.
2. There are 5 settings pages available (P1 ~ P5), press the ➡️ to switch to P5; it will automatically calibrate.
3. Short press ⏸️ to recalibrate; the value flashes during calibration, and does not flash after calibration is successful.
4. After the calibration is successful, press ⚙️ to save and exit (Automatically exit in 20 seconds if no operation detected).

Press ➡️ to switch pages. Press ⏸️ to recalibrate.

Save and get back (Automatically exit if no operation detected in 20 seconds).

GPS Positioning

1. GPS searching is Auto after power on. Please start cycling after the GPS positioning is successful.
2. If you start riding when the GPS is not positioned successfully (speed sensor not connected), the speed data (real-time, average, maximum) will be displayed as "--.--", and the rest of the data remains the same.
3. Tips: You can stand still 3-5 minutes to get more connections with satellites for better GPS signal.

GPS Signal Status:

• No signal: ?❌
• Weak: ? (weak)
• Normal: ? (normal)
• Strong: ? (strong)

Note: Please make sure you are outdoor when positioning. Bad weather and dense forest may affect GPS signal.

Cycling

Turn on the device, press ⏸️ to start an exercise and recording. During cycling, when the cycling speed is 0, the device will pause automatically. If no data for speed, cadence, and heart rate is received in 15 minutes, the device will turn into sleep mode. Press ⏸️ to resume.

Press ⏸️ to start/pause/continue. Hold ⏸️ to stop exercise and save riding data. Press ➡️ to switch the display. Press ▶️ to mark a new lap.

Bluetooth Connection

Download CoospoRide App

Download CoospoRide in Google Play or App Store.

(App Store Icon: Apple App Store, Google Play Store Icon: Google Play Store)

Compatible with

• iOS 9.0 version and above, iPhone 4s and above
• Any Bluetooth 4.0 enabled Android device with Android 4.3 and above

Bluetooth Connection (Pairing)

1. Power on the bike computer (⚫).
2. Open the CoospoRide App, enter the binding computer step, select the BC107 computer in the device list to bind the device. (The phone needs to turn on Bluetooth and allow Bluetooth permissions).

(Diagram description: Step 2 shows the bike computer screen. Step 3 shows the App screen with 'Bind' and a device list including 'BC107'.)

Bluetooth Connection (Data Synchronization)

1. In the activity page of the App, click on the connected device to enter the record synchronization operation page. (Through authorization to Strava in the App more settings, the computer data can be synchronized to the Strava platform at the same time).
2. Select the record to be synchronized and click Sync (?). The record on the computer will be deleted automatically after synchronization.

(Diagram description: Step 4 shows the App activity page with 'ID:x Connected' and 'No record'. Step 5 shows the App screen with a list of records and sync options.)

Basic Parameters

Attentions

The water resistant level of the bicycle computer is IPX7. It can be used in the rain if you close the protective cover on the back tightly. It is recommended to take down the bicycle computer and put it into a waterproof bag if it rains heavily.

Responsibility Disclaimer

• The information contained in this manual is for reference only. The product described above may be subject to alteration owing to the manufacturer's continuing research and development plans, without making an announcement in advance.
• We shall not bear any legal responsibility for any direct or indirect, accidental or special damages, losses, and expenses arising from or in connection with this manual or the contained product.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• 1. This device may not cause harmful interference, and.
• 2. This device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

• 1. This device may not cause interference.
• 2. This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

• 1. L'appareil ne doit pas produire de brouillage;
• 2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement.

Disposal and Safety

Waste electrical products should not be disposed of with household waste. Please recycle (♻️) where facilities exist. Contact your local government or a retailer for additional information.

• Do not open or modify the product. (⚠️)
• Do not disassemble or attempt to service this product. (⚠️)
• This product is safe under normal and reasonably foreseeable operating conditions.
• If product is operating improperly, call COOSPO support.
• Product must be returned to the manufacturer for any service or repair.