Outsunny 845-171 Storage Shed Assembly Instructions
Model Number: 845-171
Assembly Preparation
Please check local building codes regarding footings, location, and other requirements before beginning construction. Study and understand this owner's manual for important information and helpful tips for easier and more enjoyable assembly.
Assembly Instructions:
Review all instructions and appropriate information before you begin. Make sure to follow the step sequence carefully for successful results.
Flooring Base:
The site must be prepared so that the base of the shed is level all around, and checking with a spirit level is required. The base can be constructed with treated timber or concrete to prevent moisture from entering the shed. The shed is not designed to be built directly on a lawn. Also, the ground may become muddy during rainy days.
If a concrete pad is made, it is important that it slopes towards the edges to prevent water ingress. Time must be allowed for any concrete or cement to dry before building the shed on top.
Bases can also be constructed from bricks, blocks, or mounted on a concrete pad. The bricks or blocks should be cemented onto firm and level concrete footings, and the greenhouse frame drilled and screwed to the base.
Parts and Parts List:
Before you start, separate and identify all the parts and hardware to ensure you have all the necessary parts for your building (refer to the Parts List Page). Do not attempt to assemble the building if parts are missing, as any building left partially assembled may be seriously damaged by light winds.
Safety Must Be Put in the No. 1 Position:
- Select a dry and calm day for your assembly. Teamwork (two or more people) is required during assembly.
- Wear safety gloves, eye protection, and long sleeves during assembly to prevent injury. Pay attention to the sharp edges of some parts.
- Children and pets are not allowed on the construction site.
- Never concentrate your total weight on the roof of the building. When using a step ladder, make sure it is safe.
Care & Maintenance:
- Keep the shed clean with a soft cloth, using water if necessary.
- Keep the door tracks clear of dirt and other debris that prevent them from sliding easily.
- Clean snow with necessary tools to ensure safe entry. Heavy snow may cause collapse; please ensure safety before entering.
- The shed is not made for living but for storing items.
Parts List
The following tables list all the parts and their quantities required for assembly.
Page 2: Parts List 1/2
| NO. | PART | QTY. |
|---|---|---|
| D1 | 1 | |
| D2 | 1 | |
| P1 | 8 | |
| P3 | 8 | |
| P5 | 4 | |
| P6 | 2 | |
| P7 | 2 | |
| 25A | 1 | |
| 25B | 1 | |
| 4A | 4 | |
| 6A | 1 | |
| 19 | 1 | |
| P2 | 8 | |
| 16 | 2 | |
| 17 | 2 | |
| 6 | 1 | |
| 7 | 1 | |
| 8 | 1 | |
| 15 | 4 | |
| 20 | 4 | |
| 27 | 2 | |
| 21L | 2 | |
| 21R | 2 |
Page 3: Parts List 2/2
| NO. | PART | QTY. |
|---|---|---|
| 25R | 1 | |
| 25L | 1 | |
| 4L | 1 | |
| 4R | 1 | |
| 5 | 1 | |
| 3L | 1 | |
| 3R | 1 | |
| B1 | 4 | |
| 9 | 1 | |
| 11 | 1 | |
| 10L | 1 | |
| 10R | 1 | |
| 1 | 1 | |
| 2 | 1 | |
| 3 | 1 | |
| 4 | 4 | |
| 13 | 1 | |
| 14 | 1 | |
| GB | 2 | |
| GC | 4 | |
| GD | 4 | |
| G2 | 4 | |
| GL | 4 | |
| GE | 2 | |
| GF | 4 | |
| K | 1 | |
| F1 | 340 | |
| F2 | 70 | |
| F3 | 12 | |
| S2 | 340 | |
| S1 | 340 |
Assembly Steps
Step 1: Frame Assembly
Attach part 1 to part 4L using screws F1. Ensure a secure fit.
Attach part 1 to part 4R using screws F1. Ensure a secure fit.
Step 2: Side Panel Assembly
Connect part 2 to the frame using screws F1.
Step 3: Front Panel Assembly
Attach part 1 to the front frame using screws F1.
Attach part 3L and 3R to the front frame using screws F1.
Step 4: Base Assembly
Attach part 5 to the frame using screws F1.
Step 5: Corner Post Assembly
Attach corner posts (e.g., 25L, 25R) to the base and side panels using screws P3 and S2.
Step 6: Wall Panel Installation
Install wall panels (e.g., P1, P2, P3) into the frame, securing them with screws F1 and S2.
Note: The top row of holes may not require screws.
All panels are lapped in this way.
Step 7: Roof Beam Installation
Attach roof beams (e.g., 10L, 10R) to the top of the shed using screws F1 and S2.
Step 8: Roof Panel Installation
Install roof panels (e.g., P5, P6, P7) onto the roof beams, securing them with screws F1 and S2.
Step 9: Roof Support Installation
Attach roof supports (e.g., 15, 16, 17) to the roof structure using screws F1, F3, and S2.
Step 10: Roof Cap Installation
Install roof caps (e.g., GC, GE, GL) onto the roof structure using screws F1 and S2.
Step 11: Door Frame Assembly
Assemble the door frame using parts D1, D2, and GB, securing with screws F2.
Step 12: Door Panel Installation
Attach the door panels (e.g., 25A, 25B) to the door frame using screws F1 and S2.
Step 13: Door Hinge Installation
Attach hinges to the door and the shed frame using screws F3.
Step 14: Final Touches
Ensure all screws are tightened and all panels are securely in place. Align the gasket with the hole and use an electric drill to insert S2 into the hole.
Contact Information
For any questions or assistance, please contact the customer care center:
- US: 001-877-644-9366, customerservice@aosom.com
- CA: 416-792-6088, customerservice@aosom.ca
- UK: 0044-800-240-4004, enquiries@mhstar.co.uk
- FR: 0033-1-84166106, aosom@mhfrance.fr
- DE: 0049-0(40)-88307530, service@aosom.de
- ES/PT: 0034-931294512, atencioncliente@aosom.es / info@aosom.pt
- IT: 0039-0249471447, clienti@aosom.it
Imported by:
- US: Aosom LLC, 27150 SW Kinsman Rd Wilsonville, OR 97070 USA
- CA: Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9
- UK: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South Perivale, UB6 7RH
- FR: MH FRANCE, 2 Rue Maurice Hartmann 92130 Issy Les Moulineaux France
- DE: MH Handel GmbH, Wendenstraße 309 D-20537 Hamburg Germany
- ES: SPANISH AOSOM, S.L. C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN.
- PT: SPANISH AOSOM, S.L C.ROC GROS N.15, 08550. ELS HOSTALETS DE BALENYÀ
- IT: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1 20057 Assago (MI)
All products made in China.
