PAX A35 POS Terminal User Manual

Note: Product images shown may be different than actual product received

PAX TECHNOLOGY LIMITED

1. Product Description

2. Specifications

3. Instructions

The A35 connects to a POS or an ECR via a communication cable for entering passwords, tapping contactless cards, swiping magstripe cards, inserting smart cards, or reading 1D/2D codes during a transaction process. To use it correctly, refer to the following instructions:

1. Power Connections

   Power can be supplied to the A35 by connecting the AC power adapter to the communication cable, as in the case of RS232 or USB configurations, or via a powered USB cable (12V Powered USB) where the connected POS terminal provides the power.

2. Reset

   Press and hold the 'X' and 'O' buttons for 5-8 seconds; the operation system will reboot.

3. Communication cable
   1. Remove the back cover (At the bottom of the terminal).
   2. Connect the communication cable head to the Type-C interface.
4. SAM Cards
   1. Remove the back cover (At the bottom of the terminal).
   2. Insert the SAM cards into the corresponding card slot.
5. SD Card
   1. Remove the back cover (At the bottom of the terminal).
   2. Insert the SD card into the corresponding card slot.
6. Magnetic stripe card reader

   To use the magnetic stripe card reader, position the magnetic stripe side of the magnetic card towards the device interior. Swipe the card with a steady speed through the magnetic reader slot. (Supports bi-directional swiping).

7. IC card reader

   To use the IC card reader, place the IC card chip side upward and push it into the IC card slot until it stops.

8. Contactless card reader

   To use the contactless card reader, tap the contactless card on the Top LCD screen area of the device, indicated by the universal contactless icon on the screen, when prompted.

9. 1D/2D code reader

   To use the 1D/2D code reader, position the 1D/2D code towards the top center area of the LCD.

10. Electronic signature

    The A35 supports electronic signatures. Please use your finger to sign; do not use metal or sharp objects to operate the touch screen to avoid damage.

11. Terminal Anti-theft

    The A35 provides a Kensington security hole on the rear side of the terminal. End users can lock the terminal to a countertop with a Kensington lock if necessary.

12. Audio Jack

    If required, a visually impaired person can connect headphones to the terminal for audio prompting if the terminal application supports this feature using the 3.5mm output audio jack.

4. Installation and Usage Tips

1. Avoid placing the terminal in direct sunlight, high temperature, moist, or dusty environments.
2. Do not allow non-professionals to repair the terminal.
3. Before inserting a card, check the inside and around the IC card slot. Report any suspicious objects to the relevant administrator.

5. Password Entering Tips

It is highly recommended to enter passwords using the following methods:

1. Set up anti-peep shields. Enter the password with a shield provided by the cashier's desk structure.
2. Position the POS terminal at an appropriate angle to make it difficult for others to see the password. For example, the POS can be installed on a movable bracket.
3. When entering the password, avoid areas with surrounding video surveillance.
4. Post instructions reminding customers to shield their entry with their body or palm when entering their password.
5. Merchants can also implement other methods to protect customer password input.

FCC Regulations

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RF Exposure Information

This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

ISED Notice

This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en affecter le fonctionnement.

IC: 11689A-A35BW

ISED RF Exposure Statement

This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 définies pour un environnement non contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la CNR-102, la proximité humaine à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal.

PAX TECHNOLOGY LIMITED

PAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying.

Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: 0755-86169630
Fax: 0755-86169634
Website: http://www.pax.com.cn

Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville,
Florida, USA 32256
Help-desk

1 877-859-0099