PAX E700 Pro Integrated Smart Terminal

1. Contents Checklist

Please check the components after unpacking. If any are missing, please contact the dealer.

2. Product Description

Front View:

The front view of the E700 Pro shows the following components:

• Printer Button
• Fingerprint Reader
• Printer Paper Exit
• Power & Printer Indicator
• Power Button
• Light Sensor
• Cashier-facing Scanner
• LCD Display

Q20 view:

The Q20 view shows the consumer-facing side, including:

• Hybrid Card Reader
• Customer-facing Scanner
• Contactless Area

3. Terminal Ports

The following ports are accessible on the back of the E700 Pro:

Ports View:

The back of the terminal features:

• Cash Drawer Port
• Power Port
• Battery Cover
• Audio Jack
• RS232 Port
• USB-A/B Host Port
• USB-Slave
• LAN
• Fiscal Module Cover

Side View:

The side view indicates volume controls:

• Volume+
• Volume-

Detailed description of ports:

• Power – Connect AC power supply to E700 Pro.
• Cash Drawer – Insert the cable from cash drawer to connect with cash register.
• Audio Jack - Allows hearing impaired to connect assistive listening device.
• USB Host – Connect USB device. USB A-HOST output: 5V 500mA.
• RS232 - Used to connect to serial device such as an external POS device or check reader.
• USB - SLAVE – Used for local terminal download.
• LAN – Used for bi-directional Ethernet connections.

The back cover can be opened to access the following ports:

• SD Card Slot – Open card cover, remove battery and insert card into SD card slot.
• SIM Card Slot – Open card cover, remove battery and insert SIM card into SIM slot to connect to cellular carrier's network.

4. Power ON/OFF

• Power on: Press and hold the Power button for three seconds until the main screen displays normally. (See page 1 for the location of the Power button.)
• Power off: Press and hold the Power button for three seconds until the shut down menu displays. Select Power off. The terminal turns off after a few seconds. (See page 1 for the location of the Power button.)

5. Hybrid Card Reader

The Q20 on the consumer-facing side of the E700 Pro includes a reader that can be used as a Magnetic Stripe, EMV, and NFC/Contactless card reader.

• Magnetic Stripe Reader: Insert the card into the reader slot located on the top of the Q20. The terminal reads the information from the card when the magnetic stripe is inserted into the card slot.
• EMV Card Reader: Insert the card with the front facing you and the chip down into the card slot. Leave the card inserted until the terminal prompts to remove the card.
• NFC/Contactless Card Reader: Tap the card to the Q20 screen when prompted. The terminal uses an antenna device that detects and retrieves information from the card.

6. Specifications

• Operation System: Android 10.0
• CPU: Octa-core Cortex™-A55, 1.6GHZ
• Memory: 3GB DDR+32GB eMMC
• Main Display: 12.5 inch, 1920x1080 resolution, capacitive touch screen
• Printer: 3" high-speed thermal printer with auto-cutter, printing speed 150mm/s, paper width 80mm, diameter 80mm
• Audio: Built-in speaker, support headphone output
• Camera with scan window: (coverage of 30mm-120mm) for 1D/2D scan
• Front fixed focus camera with 0.3 mega pixels (facing to cashier)
• Rear fixed focus camera with 2 mega pixels (facing to customer)
• L-Sensor (Ambient Light Sensor): Automatically adjust the backlight brightness of the main display
• Wireless Communication: Supports LAN, WIFI, Bluetooth, 3G/4G
• Peripheral Ports: Power port x1, USB A ports x4, USB C port x1, LAN x1, Cash drawer x1, Serial port x1, Audio jack x1
• Card Slot: SIM card slot x1, Micro SD card slot x1
• Magnetic Card Reader: Supports track 1/2/3.
• IC Card Reader: Conforms to the standard of ISO7816, EMV2000 L1&L2, PBOC3.0
• Contactless Card Reader: Compatible with ISO14443 Type A&B

7. Load Printer Paper

1. When the printer is out of paper, the yellow "Paper Out" indicator lights. Press the button on the left of printer to open the cover.
2. Load the paper roll into the paper compartment and extend the end of the paper out of the printer.
3. Close printer cover. The Paper Out indicator light turns off.

8. Installation and Usage Tips

• Avoid exposing the device to an excessively hot, humid, dusty, or strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered on. This may cause damage to an internal circuit.
• Please contact PAX technical support for assistance with the device.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio equipment type E700 Pro is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at: http://www.pax.com.cn/ProductCE.aspx

Regulatory Information

Icon shows:

• The mains plug is used as the disconnect device. The socket-outlet shall be installed near the equipment and shall be easily accessible.
• This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

Warning

• Moving parts: Keep body parts away from moving parts.
• To avoid replacement of a battery with an incorrect type.
• Do not dispose of a battery into fire or a hot oven, or mechanically crush or cut a Battery.
• Do not leave a battery in an extremely high temperature surrounding environment.
• To avoid battery subjected to extremely low air pressure.
• The marking information is located at the bottom of the apparatus.

FCC Regulations:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

ISED Notice

• This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
• Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
• This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.
• Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.
• The County Code Selection feature is disabled for products marketed in the US/ Canada.
• La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre leradiateur et votre corps.

The device for operation in the band 5150 – 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Le dispositif a été utilisé pour la construction de la bande 5150 à 5250 MHz pour la consommation de matériel pour réduire le potentiel pour les systèmes de télévision mobiles.

FCC Supplier's Declaration of Conformity

Integrated Smart Terminal / E700 Pro

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party: PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville, Florida, 32256
Help-desk
1 877-859-0099

PAX TECHNOLOGY LIMITED

Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.
Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: 0755-86169630
Fax: 0755-86169634
Website: http://www.pax.com.cn
Responsible Party: PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville, Florida, 32256
Tony Fernandez
tony.fernandez@pax.us
+1 623-640-9529