LOOP - M-DS

Parts List

A comprehensive list of components included with the LOOP - M-DS unit.

• Lid (Deckel): 1 piece
• Side Panel (Seitenteil): 4 pieces
• Front Panel (Vorderseite): 3 pieces
• Rear Panel (Rückseite): 1 piece
• Left & Right Feet (Fuß links & rechts): 2 pieces
• Intermediate Element (Zwischenelement): 2 pieces
• U-Profiles (U-Profil): 2 pieces
• Assembly Aid (Montagehilfe): 4 pieces

Hardware

• M6 Screw/Nut (DIN 692112/12 mm, DIN 934 A2 M6): 17 pieces
• M8 Nut/Screw (DIN 6921 A2/20 mm, DIN 6923 A2 M8): 4 pieces
• M10 Hammer Head Screw (ART. 4141 M10x30/30 mm, DIN 6923 A2 M10): 4 pieces

Blocker

For installation details of the Blocker, please refer to the "Installation Lufttrennung" (Air Separation Installation) section.

Note: Screw packages are designed for the largest variant; therefore, some screws may be left over.

Recommended Tools:

• Open-end wrench: M6 (10 mm wrench size), M8 (13 mm wrench size), M10 (17 mm wrench size).
• A ratchet wrench set with sockets is ideal, especially for tight spaces.

Additionally Helpful:

• Torque wrench
• Gloves

For further information, including warranty exclusions, liability limitations, and our General Terms and Conditions, please visit: www.urban-shell.com/policies/terms-of-service

Installation - Soundproofing

Note: The installation of soundproofing is only relevant if you have purchased a SOUNDPROOFING SET BASIC or KOMFORT as an accessory. If this is not the case, please ignore this page and proceed to the next.

Surface Preparation: For optimal adhesion of double-sided tape, proper surface preparation is crucial. Ensure the substrate is clean, dry, and free from dust, oil, or grease. Contamination can significantly impair adhesive strength.

Temperature: Temperature also plays an important role during application. Most adhesive tapes develop their full adhesive strength only at a processing temperature of at least +10°C. At temperatures that are too low, the adhesive can harden and adhere poorly.

Tip: Press the soundproofing component firmly after application to maximize contact with the substrate.

Soundproofing Set Comfort - Double Application for Figures B & C

Step A: Applying Soundproofing to Front and Rear Panels

Apply soundproofing material to 3x Front Panels (each with 7 lamellae) and 1x Rear Panel (with 5 lamellae). This involves applying the soundproofing material (T01) to the lower edge of each lamella.

Step B: Applying Soundproofing to the Lid

Apply soundproofing material to the Lid (1x). Apply material T02 centrally and T03 to the lower edge of the lamellae.

Step C: Applying Soundproofing to Side Panels

Apply soundproofing material to 4x Side Panels (2x right / 2x left). Apply material T04 to the lower edge of the lamellae and T05 centrally.

Installation - Blocker

Important:

The Blocker prevents an air short-circuit within the housing. For better illustration, the Blocker is shown in yellow here; in the actual version, it is black, matching the rest of the soundproofing material.

Side View Overview:

The diagram shows the side view of the unit with airflow, the blocker component, the heat pump's rear wall, and the design hood's rear wall.

Minimum Clearances:

• Device Height: Minimum clearance of 80 mm to the lid.
• Device Width: Minimum clearance of 80 mm to each side.
• Device Depth: Minimum clearance of 80 mm to the rear wall and 110 mm to the front panel.

Adhesive Positions for Blocker:

Note: The number of blocker strips can vary depending on the manufacturer/device type/soundproofing set. The crucial point is that the blocker fits snugly against the device without large gaps.

• A: Adhesive position for the Blocker on the Left Side.
• B: Adhesive position for the Blocker on the Right Side.
• C: Adhesive position for the Blocker on the Lid.
• D: Adhesive position for the Blocker inside the Hood.

Installation - Compressor Housing

Accessory Note: If you have not purchased a compressor housing, please ignore this page.

The installation of the compressor housing is only relevant if one was purchased. If this is not the case, please ignore this page and proceed to the next.

Surface Preparation & Temperature: For optimal adhesion of double-sided tape, which is applied to the back of the insulation nails, proper surface preparation is crucial. Ensure the substrate is clean, dry, and free from dust, oil, or grease. Contamination can significantly impair adhesive strength. Temperature also plays an important role: Most adhesive tapes develop their full adhesive strength only at a processing temperature of at least +10°C. At temperatures that are too low, the adhesive can harden and adhere poorly.

Tip: Press the insulation nails firmly after application to maximize contact with the substrate.

Step A: Apply Insulation Nails

Peel off the film from the underside of the insulation nails and apply them to the device as shown, on the front, rear, sides, and lid. Press firmly.

Step B: Attach Insulation

Slide the insulation pieces onto the insulation nails. Apply to all 4 sides.

Step C: Attach Clips

Slide the insulation holding clips onto the tips of the nails and press them on.

Step D: Finished

Assembly Instructions

Step 1: Lid + Right Side

Connect the Lid and the Right Side panel using 3x M6 screws. Ensure the opening is at the bottom.

Step 2: Front + Left Side

Connect the Front panel and the Left Side panel using 3x M6 screws. Ensure the opening is at the top.

Step 3: Right Side + Intermediate Element

Connect the Right Side panel to an Intermediate Element.

Step 4: Left Side + Intermediate Element

Connect the Left Side panel to an Intermediate Element.

Step 5: Lid + Right Side (Continued)

Connect the Lid and the Right Side panel using 3x M6 screws. Ensure the opening is at the bottom.

Step 6: Front + Left Side (Continued)

Connect the Front panel and the Left Side panel using 3x M6 screws. Ensure the opening is at the bottom.

Step 7: Right Side + Right Foot

Attach the Right Foot to the Right Side panel using 4x M6 screws. Note: The tab (B) on the foot should be at the bottom, and the cutout (A) on the side panel should be at the top.

Step 8: Left Side + Left Foot

Attach the Left Foot to the Left Side panel using 4x M6 screws. Note: The tab (B) on the foot should be at the bottom, and the cutout (A) on the side panel should be at the top.

Step 9: U-Profile onto Damping Base

Attach the U-profile to the damping base using 4x M10 screws.

Assembly Aid (A)

If necessary, assembly aids can be attached to create a mounting surface for the mounting rails. These are fastened with 4x M8 screws. Purpose: Adapter for wall bracket, extension for mounting rail, washer for grating.

Step 10: Place Feet onto Mounting Rail

Position the Right/Left Feet onto the mounting rail using 4x M10 screws.

Step 11: Front Panel Assembly

Turn nuts onto bolts for the Front Panel. Leave a 2 mm gap. Use 6x M6 screws.

Step 12: Rear Panel Assembly

Turn nuts onto bolts for the Rear Panel. Leave a 2 mm gap. Use 6x M6 screws.

Step 13: Front and Rear Panel Connections

Turn nuts onto bolts for the Front and Rear Panels. Use 4x M8 screws.

Step 14: Insert Front Panel 1

Insert the first Front Panel into position.

Step 15: Insert Front Panel 2

Insert the second Front Panel into position.

Step 16: Insert Front Panel 3

Insert the third Front Panel into position.

Step 17: Insert Rear Panel

Insert the Rear Panel into position.

Completion:

You have successfully assembled your LOOP soundproofing hood! We appreciate your feedback - please rate us at: www.urban-shell.com

Accessories

Soundproofing Sets:

• Level 1: BASIC Soundproofing Set (up to 6.6 dB damping). For basic soundproofing applications.
• Level 2: KOMFORT Soundproofing Set (up to 8.0 dB damping). Enhanced use of insulation material for increased soundproofing performance.
• Level 3: PREMIUM Soundproofing Set (up to 10 dB damping). For maximum sound insulation, used in combination with the KOMFORT set and compressor housing.

Available Accessories:

• Damping Base (2 pcs)
• Base Cladding
• Compressor Housing (up to 10 dB(A))
• Anti-theft protection

Found something nice? Contact us easily via info@urban-shell.com

Technical Data

Product: LOOP

Dimensions (H x W x D):

• S: 760 x 1000 x 500 mm
• M: 787 x 1260 x 790 mm
• L: 980 x 1260 x 790 mm
• XL: 935 x 1545 x 963 mm
• M-DS: 1532 x 1260 x 790 mm
• L-DS: 1720 x 1260 x 790 mm
• L-PLUS: 1102 x 1210 x 670 mm
• L-TALL: 1422 x 1110 x 770 mm
• XXL: 1117 x 1650 x 1033 mm
• Custom sizes available upon request.

Material:

Full aluminum 2.0 mm

Coating:

Structure powder-coated.

• Grey (RAL 7043) / White (RAL 9002)
• Grey (RAL 7043) / Red (RAL 3009)
• Special colors available upon request.

Sound Tests:

• DIN EN ISO 3744:2011-02
• DIN EN ISO 11546-1:2010-01
• Certified by TÜV Süd

Performance Test:

• No loss of performance or efficiency.
• Tested by TÜV Süd.
• DIN EN 14511-2:2023-08