MCombo Lift Recliner Owner's Manual

Table of Contents

• I. Safety Guidelines
• II. Assembly Instructions
• III. Operating Instructions
• IV. Care and Maintenance
• V. Troubleshooting
• VI. Disassembly Instructions
• VII. Warranty
• VIII. Return/Replacement Policy
• IX. MCombo Customer Support

I. Safety Guidelines

Read the safety and other instructions thoroughly before using your MCombo® product. Failure to follow the guidelines, warnings in this manual and those located on your product can result in personal injury or product damage and will void the product warranty. Keep this manual for future reference.

1. Mandatory

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children play on or near the chair when in use. Serious injury or death could occur if a child is under the chair when the chair is in motion.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Avoid exposing upholstered chair to burning cigarettes or cigars, open flames, and high temperatures.
• Do not use this product if it is wet, in water, around water or any liquid.
• Always leave in an upright and closed position. Keep hands and feet clear of mechanism and all moving parts. Footrest must be completely closed before getting in or out of the chair. Only the occupant should operate the chair.
• Before moving the product, disconnect the electrical plug from the wall outlet and secure the mechanism to prevent unexpected lifting and movement of the chair.

2. Danger

• Do not attempt to disassemble or repair the actuator or pump; no serviceable parts are inside.
• Do not allow electrical cord to be pinched between moving parts or between the frame and the floor. Do not place cord under carpet or in a location where it could become worn.
• Do not use pillow, blanket, or other cover between occupant and chair surface when heat is engaged.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around furniture.
• Unplug power cords from outlet before relocating or troubleshooting.
• This product has many moving parts, serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug or connector.
• This product is not intended for use as a health care device. Some medications and physical limitations may impair your ability to operate this product in a safe manner. Consult your physician if you are taking prescribed or over the counter medication, or if you have physical limitations.
• Do not charge your device into the USB charge ports over 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not overlay the USB charge ports with other heat-dissipating electronic products. This may prevent heat dissipation and cause overheating or melting.
• Users of medical devices should contact their health care provider before using this product.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact your MCombo Customer Support.
• Burns may result from improper use and care of internal heating parts. To avoid risk of burns, do not use pins, do not allow heating pad area to become wet, and do not remove upholstery cover.
• The chair is intended for a single occupant, not exceeding 320 pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
• If you give this product to someone else, must include this owner's manual.

3. Warning

• Weight Capacity: 320 lbs.
• Do not use outdoors. INDOOR USE ONLY.
• To avoid tip over, do not put your weight against the back of the chair.
• Do not stand, sit, or place extra weight on the arms, back or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Do not use this product if you have poor circulation, are mobility-impaired, or cannot sense heat, except as directed by your health care provider.
• Do not operate the unit until the back is installed and locked.

4. Symbols Information

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. It is especially important for you to read and understand these symbols completely. Do not remove these labels from your product. Please note that not all the symbols may be used on your chair.

• Icon: Document with text 'Read and follow the information in the owner's manual'
• Icon: Footrest with an 'X' over objects underneath - Do not place objects under the footrest when it is in a fully reclined position.
• Icon: Scale with '320 lbs' text - Weight capacity: 320 lbs.
• Icon: Power plug with an 'X' over an extension cord - Do not connect an extension cord to the AC/DC converter.
• Icon: Chair with an 'X' over objects underneath the base/transformer - Do not cover or place the external transformer and other objects under the lift chair.
• Icon: Hands near moving parts with an 'X' or warning triangle - ⚠️ Pinch/Crush Points Hazard.
• Icon: Lightning bolt - ⚡ Electrical Hazard.
• Icon: Square within a square - Class II Equipment.
• Icon: House with an 'X' over an outdoor scene - Indoor Use Only.

5. Disclaimer

Make sure you read and understand this manual completely before using your MCombo Product. We are not and cannot be held responsible for any damage or injury incurred due to improper or unsafe use of the MCombo Product. We specifically disclaim responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances.

II. Assembly Instructions

Please read these instructions thoroughly before using.

• Do not plug the power supply in until assembly is complete.
• Choose a location for the lift chair that is close to an electrical outlet (1 power outlet required).

1. Product Parameters

2. Part List

Notice: Use MCombo parts only for all replacements.

Box 1 of 2

• A Base x 1: Illustration of the chair base.
• C1 Right Armrest with USB x 1: Illustration of the right armrest with USB port.

Box 2 of 2

• B Backrest x 1: Illustration of the backrest.
• C2 Left Armrest x 1: Illustration of the left armrest.
• D Lift Remote x 1 (Model: 6160-BB-LR1): Illustration of the lift remote.
• E Massage Remote x 1 (Model: 6160-BB-BM): Illustration of the massage remote.
• F Angle Power Cord x 1 (Model: 6160-BB-APC): Illustration of the power cord.
• G Anti-back-tipping x 2 (Spare parts): Illustration of anti-back-tipping hardware.
• H Rack circular gasket x 2 (Spare parts): Illustration of circular gaskets.

3. Assembly Steps

Step1 - Armrest Assembly

1. Ensure the armrest which has USB charge port is located on the right of the base.
2. Slide the left and right armrest into the brackets of the base.
3. Press each armrest down as far as it will go. (Illustration showing armrests sliding into base brackets and being pressed down).

NOTE: Ensure the two connections on each armrest are both inserted into the seat tightly.

Step2 - Backrest Assembly

1. Align the brackets of the backrest at the clips of the seat-back. (Illustration showing backrest brackets aligning with seat clips).
2. Push the brackets into the seat-back tightly. Listen for a "click" sound on each side to ensure the backrest is locked in properly.

NOTE: Pull up the backrest to check if it is locked in place.

ATTENTION: Remove the plastic cap before assembling the backrest.

Step3 - Lift Connections

1. Connect the chairs according to the following wiring diagram. (Diagram showing electrical connections between motor, hand control, and power adapter).
2. Attach the chair-back to the velcro on the bottom of the chair base.

Step4 - Anti-back-tipping Part Assembly

1. Place the Anti-back-tipping parts (G) near the bottom of the base.
2. Align the screws with the holes then tighten the wing screws. (Illustration showing anti-back-tipping parts being attached to the base with screws).

Step5 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (Note: There are two metal brackets on each side of the base; it looks like assembly is finished when you insert the armrest into only one bracket instead of two, however, all pressure will apply to one bracket, which is a likely reason that the armrest falls apart from the seat.)
2. Make sure the backrest inserts are locked to the base. (Pull up the backrest to check if it is locked in place.)
3. Make sure all wires are connected tightly.
4. Make sure all wires are not placed on the bottom of the rack and will not be pressed by the frame. (If the wire is pressed by the frame, the wire will be broken by the frame and the chair will stop working.)
5. Make sure the anti-tilt fitting screws are tightened.

III. Operating Instructions

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Do not use outdoors. INDOOR USE ONLY.
• Stay away from the backrest from the wall at least 16 inches before using.
• Use this lift only for its intended use as described in the operating instructions.
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Ensure the hand control is out of the way before sitting in the chair.
• Always leave the lift chair in an upright and closed position when not in use.
• Periodically check the hand control and all power cords for visible damage.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the chair-back while in a recline position.

NOTE: If you discover a problem at any point during the setup and positioning of your lift chair, stop and contact the MCombo Customer Support immediately. To avoid personal injury and/or product damage, do not plug the unit into the electrical outlet until the problem is corrected and do not attempt to fix electrical problems by yourself.

2. Lift Remote Operation Instruction

• LIFT (UP): Press and hold the UP button to raise the chair to the full-lift position. Press and hold the UP button to return to the seated position from the reclined position.
• LIFT (DOWN): Press and hold the DOWN button to lower the chair to the seated position. Press and hold the DOWN button to raise the footrest and recline the chair back.

(Illustration of the lift remote with UP and DOWN buttons labeled)

3. Massage Remote Operation Instruction

(Illustration of the massage remote with buttons: HEAT, POWER, MODE, TIMER, INTENSITY, POINTS)

NOTE: Use the heating only: Turn off the POWER button, turn on the HEAT button. (Heating function works with vibration separately.)

IV. Care and Maintenance

Your MCombo product will provide years of superior performance and satisfaction with regular care and maintenance. To maintain the finish quality of your "assistant", please follow the guidelines and cleaning procedures provided below.

Notice

• Do not place your chair in direct sunlight, as sunlight causes fading.
• Do not smoke cigarettes while sitting in or using your chair.
• Avoid extreme changes in temperature by arranging chair away from radiators, heat and air vents.
• Do not use solvent-type cleaners to spot clean.
• Do not saturate fabric.
• Please be careful that pet scratch may cause fabric or leather break.

1. Fabric Care

• Inspect the fabric on a regular basis for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a nonmetallic, stiff bristle brush to remove dust and grime is recommended.
• When liquid spills onto the fabric, please immediately wipe off liquid spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Make sure that the cloth is not soaking wet. Never let water soak into leather.
• Always be sure to use a soft cloth and never use an abrasive brush or scrubber as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to make sure they are not damaged or stuck under chair.
• Keep all the electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact MCombo Customer Support if damage is present; do not fix it by yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, electronic components.

V. Troubleshooting

The following troubleshooting FAQs should summarize what you need to know about your power recliner sofa. If at any time you do not feel comfortable performing the troubleshooting steps listed in this manual, please contact MCombo Customer Support for service.

NOTE: If the lift recliner still does not operate properly, please contact the MCombo® Customer Support for help and never attempt to make any repairs or adjustments yourself.

Lift Motor Replacement

NOTE:

1. Take an original bottom picture for reference before disassembling.
2. The disassembled small parts need to be put away to prevent falling into the rack.

Step1 - Turn the Chair to the Left

First, turn the chair to the left. The right armrest is upward. Be careful not to break the wire of the USB charge ports.

Step2 - Remove Bolts

1. Illustration showing the original position of the paper clip.
2. Illustration showing twisting the paper clip.
3. Illustration showing pulling out the paper clip.
4. Illustration showing pulling out the bolt.

Repeat "Step 2" with the other end of the lift motor.

Step3 - Remove Old Lift Motor

(Illustration showing the removal of the old lift motor).

Step4 - Replace the New Lift Motor

Replace the new lift motor.

NOTE: Please note that the motor of the lift motor is facing the ground. Be careful not to install it backwards, otherwise the lift motor will break.

Step5 - Install Bolts

Insert bolts and paper clips at both ends of the lift motor.

(Illustration showing inserting the bolt and then the paper clip).

Step6 - Final Check

Check & Confirm

1. Make sure bolts and paper clips are fully inserted.
2. Make sure the lift motor is installed in the correct direction.
3. Make sure the wires are not crushed by the seat frame.

(Illustration showing the final check of the motor installation).

VI. Disassembly Instructions

Notice:

• Ensure the chair is in seated position and its footrest return to original position.
• Please unplug the power cord before disassembling.
• Please refer to the installation steps from back to front and disassemble the chair in reverse order.

Step1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step2 - Disassemble Backrest

1. Pushing the metal ears of the backrest inserts outward. (Illustration showing pushing metal ears outward).
2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward. (Illustration showing pulling the backrest upward).

ATTENTION: After unlocking the metal tabs on both sides of the backrest, pull the backrest upward.

Step3 - Disassemble Armrests

NOTE:

• Need to remove the backrest first.
• It is best to remove the armrest by two people.
• When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the armrest bag and cup holder.

1. Use your knees to find a support point on the seat and press on the base with your own strength.
2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward. (Refer to arrow direction and the circular marking area). (Illustration showing lifting the armrest).

ATTENTION: Shake the armrest slightly to loosen the brackets, making it easier to detach from the base.

VII. Warranty

Notice:

• For products beyond the limited manufacturer warranty period and scope, MCombo® can also provide replacement service, but a basic charge will be charged according to the circumstances.
• The warranty only applies to MCombo® products and does not include any accessories or enhancements.
• Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

All warranties begin on the date of delivery.

All warranties are to the original purchaser from MCOMBO® ONLY.

• MCOMBO® will replace the defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation.
• Exclusions also include components with damage caused by:
  • Contamination
  • Abuse, misuse, accident, or negligence
  • Commercial use, or use other than normal
  • Improper operation, maintenance, or storage

NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. We can also sell you replacement parts for a discount price when your product is out of warranty policy.

VIII. Return/ Replacement Policy

Notice

Why don't we recommend returning the item by yourself?

• Huge cost - UPS/FedEx oversize fee.
• Need you to take the box to UPS/FedEx facility.

Return/ Replacement Policy

MCOMBO®

You have 30 days from the date of purchase to return any item purchased from our store. Please securely pack the item in its original packaging, including any accessories or manuals that came with the product. To initiate a return, please contact our customer service team at sales@mcombo.com or 323-597-1109 for any help.

Return Conditions

We accept the return of items that are in new, unused condition, with original tags attached and all original packaging and other components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE:

• Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the newly found packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width+ height) * 2 + length < 128 inch.
• Please disassemble the product before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount.
• Please do not purchase return label for a damaged/defective product by yourself.
• If you have any problem to return the product, please contact us immediately, we will do our best to help you with a reasonable solution.

IX. MCombo Customer Support

For product beyond the limited manufacturer warranty period and scope, MCombo® can also provide replacement service, but a basic charge will be charged according to the circumstances.

The warranty only applies to MCombo® products and does not include any accessories or enhancements.

Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

Contact Information:

• Email: sales@mcombo.com
• Phone: 1-323-597-1109 (8:00 a.m. - 4:00 p.m. PST, Monday - Friday)
• Website: www.mcombo.com