MCombo Lift Recliner Owner's Manual

I. SAFETY GUIDELINES

1. Mandatory

• Read all safety and operating instructions thoroughly before use.
• Keep this manual for future reference.
• Keep plastic bags away from children to prevent suffocation.
• Do not allow children to play on or near the chair while in use; serious injury or death could occur if a child is under the chair when it is in motion.
• Keep power cords out of reach of small children and avoid placing them where they may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Avoid exposing the upholstered chair to burning cigarettes, open flames, or high temperatures.
• Do not use the product if it is wet, in water, or around any liquid.
• Always leave the chair in an upright and closed position. Keep hands and feet clear of the mechanism and all moving parts. Ensure the footrest is completely closed before getting in or out of the chair. Only the occupant should operate the chair.
• Before moving the product, disconnect the electrical plug from the wall outlet and secure the mechanism to prevent unexpected lifting or movement.

2. Danger

• Do not attempt to disassemble or repair the actuator or pump; there are no serviceable parts inside.
• Do not allow the electrical cord to be pinched between moving parts or between the frame and the floor. Do not place the cord under carpet or in a location where it could become worn.
• Do not use a pillow, blanket, or other cover between the occupant and the chair surface when heat is engaged.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around the furniture.
• Unplug power cords from the outlet before relocating or troubleshooting.
• This product has many moving parts; serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Regularly check the condition of the power supplies, electrical cords, plugs, and connectors. Keep power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug, or connector.
• This product is not intended for use as a health care device. Certain medications and physical limitations may impair safe operation. Consult your physician if you are taking prescribed or over-the-counter medication, or if you have physical limitations.
• Do not charge your device into the USB charge ports for more than 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not cover the USB charge ports with other heat-dissipating electronic products, as this may prevent heat dissipation and cause overheating or melting.
• Users of medical devices should consult their health care provider before using this product.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact Mcombo Customer Support.
• Burns may result from improper use and care of internal heating parts. To avoid risk of burns, do not use pins, do not allow the heating pad area to become wet, and do not remove the upholstery cover.
• The chair is intended for a single occupant, not exceeding 350 lbs. Do not operate the chair with more than one occupant.
• If you give this product to someone else, include this owner's manual.

3. Warning

• Weight Capacity: 350 lbs.
• Indoor Use Only.
• To avoid tip-over, do not put your weight against the back of the chair.
• Do not stand, sit, or place extra weight on the arms, back, or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Do not use this product if you have poor circulation, are mobility-impaired, or cannot sense heat, except as directed by your health care provider.
• Do not operate the unit until the backrest is installed and locked.

II. ASSEMBLY INSTRUCTIONS

Notice

• Please read these instructions thoroughly before using.
• Do not plug the power supply in until assembly is complete.
• Choose a location for the lift chair that is close to an electrical outlet (one power outlet required).

1. Product Parameters

2. Part List

Notice: Use Mcombo parts only for all replacements.

Box 1 of 2

• A - Base x 1
• C1 - Right Armrest with USB x 1

Box 2 of 2

• B - Backrest x 1
• C2 - Left Armrest x 1

Accessories:

• D - Power Cord x 1 (6160-BB-APC)
• E - Lift Remote x 1 (6160-BB-LR3)
• F - Massage Remote x 1 (6160-BB-BM)
• G - Anti-back-tipping x 2 (6160-AA-BW)
• H - Rack circular gasket x 2 (Spare parts)

3. Assembly Steps

Step1 - Anti-back-tipping Part Assembly

1. Place the Anti-back-tipping parts (G) near the bottom of the base.
2. Align the screws with the holes and tighten the wing screws. (Diagram shows placement of parts G and screws, and tightening).

Step2 - Armrest Assembly

1. Ensure the armrest with the USB charge port is located on the right side of the base.
2. Slide the left and right armrests into the brackets of the base.
3. Press each armrest down firmly until it clicks into place. (Diagram shows sliding armrests into brackets and pressing down).

NOTE: Ensure the two connections on each armrest are securely inserted into the seat.

Step3 - Backrest Assembly

1. Align the backrest brackets with the clips on the seat-back.
2. Push the brackets into the seat-back firmly. Listen for a "click" sound on each side to confirm the backrest is locked properly. (Diagram shows aligning backrest brackets with seat clips and pushing until locked).

NOTE: Pull up the backrest to verify it is locked in place.

ATTENTION: Remove the plastic cap before assembling the backrest.

Step4 - Lift Connections

1. Before attaching the lift remote and massage remote, guide the wires through the side loops of the armrests as preferred by the user.
2. Connect the chair's wiring according to the provided diagram. (Diagram shows wire routing and connections to the motor and power supply).
3. Attach the chair-back to the velcro on the bottom of the chair base.

Step5 - Final Check

1. Verify both metal brackets on each armrest are securely mounted on the base. (Note: Proper installation involves engaging both brackets, though pressure may primarily rest on one).
2. Confirm the backrest is locked into the base. (Pull up the backrest to test).
3. Ensure all wires are connected tightly.
4. Ensure wires are not positioned under the rack or frame to prevent damage or malfunction. (Pressed wires can break and stop the chair from working).
5. Confirm the anti-tilt fitting screws are tightened.

III. OPERATING INSTRUCTIONS

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed the recommended weight limit.
• Do not use attachments not recommended by the manufacturer.
• Indoor Use Only.
• Maintain at least 23.2 inches clearance between the backrest and the wall when in use.
• Use the lift chair only for its intended purpose as described in the operating instructions.
• Keep the chair dry; do not operate in wet or moist environments.
• Keep all cords away from heated surfaces and pinch points.
• Ensure the hand control is positioned safely before sitting in the chair.
• Always leave the lift chair in an upright and closed position when not in use.
• Periodically inspect the hand control and all power cords for visible damage.
• Do not use the footrest as a seat or for purposes outside its intended use.
• Do not lean or apply downward force to the chair-back while in recline position.

NOTE: If any issues arise during setup or positioning of your lift chair, stop and contact Mcombo Customer Support immediately. To avoid personal injury and/or product damage, do not plug the unit into the electrical outlet until the problem is corrected. Do not attempt to fix electrical problems yourself.

2. Lift Operation Instruction

The lift chair is operated using the hand control. Refer to the diagram for button functions:

• POWER HEADREST (BACK): Press and hold to return the power headrest to its original position.
• POWER HEADREST (TILT): Press and hold to tilt the power headrest to a comfortable position.
• LIFT UP: Press and hold the UP button to raise the chair to the full-lift position.
• LEAN BACK: Press and hold the DOWN button to raise the footrest.
• BACKREST (UP): Press and hold to tilt the power backrest to a comfortable position.
• BACKREST (DOWN): Press and hold to return the power backrest to its original position.

NOTE: Do not lift the chair until the backrest is in the upright position.

IV. CARE AND MAINTENANCE

Regular care and maintenance ensure the longevity and superior performance of your Mcombo product. Follow the guidelines and cleaning procedures provided below.

Notice

• Do not place your chair in direct sunlight, as sunlight causes fading.
• Do not smoke cigarettes while sitting in or using your chair.
• Avoid extreme changes in temperature by arranging the chair away from radiators, heat, and air vents.
• Do not use solvent-type cleaners to spot clean.
• Do not saturate fabric.
• Be cautious; pet scratches may cause fabric or leather to break.

1. Fabric Care

• Regularly inspect the fabric for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a non-metallic, stiff bristle brush to remove dust and grime is recommended.
• For liquid spills, immediately wipe off the spill with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water, ensuring it is not soaking wet. Never let water soak into the leather.
• Always use a soft cloth and never use an abrasive brush or scrubber, as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to ensure they are not damaged or stuck under the chair.
• Keep all electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact Mcombo Customer Support if damage is present; do not fix it by yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, and electronic components.

V. TROUBLESHOOTING

The following troubleshooting FAQs should help you address common issues with your power recliner. If at any time you do not feel comfortable performing the troubleshooting steps listed, please contact Mcombo Customer Support for service.

NOTE: If the lift recliner still does not operate properly, please contact the Mcombo® Customer Support for help and never attempt to make any repairs or adjustments yourself.

VI. DISASSEMBLY INSTRUCTION

Notice

• Ensure the chair is in seated position and its footrest return to original position.
• Please unplug the power cord before disassembling.
• Please refer to the installation steps from back to front and disassemble the chair in reverse order.

Step1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step2 - Disassemble Backrest

1. Push the metal ears of the backrest inserts outward (Refer to arrow direction).
2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward. (Diagram shows pushing metal ears and pulling backrest).

ATTENTION: After unlocking the metal tabs on both sides of the backrest, pull the backrest upward.

Step3 - Disassemble Armrests

NOTE:

• The backrest must be removed first.
• It is best to remove armrests by two people.
• When lifting the armrest, be sure to hold the bottom of the armrest to avoid damaging the armrest bag and cup holder.

1. Use your knees to find a support point on the seat and press on the base with your own strength.
2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward. (Refer to arrow direction and the circular marking area). (Diagram shows pressing down and lifting armrest).

ATTENTION: Shake the armrest slightly to loosen the brackets, making it easier to detach from the base.

VII. WARRANTY

Notice

• For products beyond the limited manufacturer warranty period and scope, Mcombo® can also provide replacement service, but a basic charge will be applied according to the circumstances.
• The warranty applies only to Mcombo® products and does not include any accessories or enhancements.
• Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

Warranty Periods

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

• All warranties begin on the date of delivery.
• All warranties are to the original purchaser from MCOMBO® ONLY.
• MCOMBO® will replace defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation.
• Exclusions also include components with damage caused by:
  • Contamination
  • Abuse, misuse, accident, or negligence
  • Commercial use, or use other than normal
  • Improper operation, maintenance, or storage

NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. We can also sell you replacement parts for a discount price when your product is out of warranty.

VIII. RETURN/ REPLACEMENT POLICY

Notice

• Why don't we recommend returning the item by yourself?
• Huge cost - UPS/FedEx oversize fee.
• Need you to take the box to UPS/FedEx facility.

Return/ Replacement Policy

MCOMBO®: You have 30 days from the date of purchase to return any item purchased from our store. Please securely pack the item in its original packaging, including any accessories or manuals that came with the product. To initiate a return, please contact our customer service team at sales@mcombo.com or 323-597-1109 for any help.

Return Conditions

We accept the return of items that are in new, unused condition, with original tags attached and all original packaging and other components included. Refunds will be issued in the original form of payment for the price of the item, including taxes.

NOTE:

• Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the newly found packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width+ height) * 2+ length < 128 inch.
• Please disassemble the product before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount.
• Please do not purchase return label for a damaged/defective product by yourself.
• If you have any problem to return the product, please contact us immediately, we will do our best to help you with a reasonable solution.

IX. LIFT MOTOR REPLACEMENT

NOTE:

1. Take an original bottom picture for reference before disassembling.
2. The disassembled small parts need to be put away to prevent falling into the rack.

Step1 - Turn the Chair to the Left

First turn the chair to the left, the right armrest is upward. Be careful not to break the wire of the USB charge ports. (Diagram shows the chair being turned onto its side).

Step2 - Remove Bolts

Illustrations show the process of removing paper clips and bolts from the lift motor assembly. Repeat for the other end of the motor.

1. Original position of the paper clip.
2. Twist the paper clip.
3. Pull out the paper clip.
4. Pull out the bolt.

Step3 - Remove Old Lift Motor

Diagram shows the lift motor being disconnected and removed. Replace the new lift motor.

NOTE: Please note that the motor of the lift motor is facing upward. Be careful not to install it backwards, otherwise the lift motor will break.

Step5 - Install Bolts

Insert bolts and paper clips at both ends of the lift motor. (Diagrams show inserting the bolt and paper clip).

Step6 - Final Check

Check & Confirm

1. Make sure bolts and paper clips are fully inserted.
2. Make sure the lift motor is installed in the correct direction.
3. Make sure the wires are not crushed by the seat frame. (Diagram shows the final assembly with the motor installed).