Mi Bedside Lamp User Manual

Welcome

Thank you for choosing the Mi Bedside Lamp. High-quality LED lights and a professional optical structure, combined with a natural light mixing algorithm, make the Mi Bedside Lamp a perfect companion for your bedside table.

Getting Started

Instruction

Unpack the lamp and connect the power cord.

Connect the adapter plug to the power supply port on the lamp, and then connect the power adapter to an electrical outlet.

* Place the lamp on a stable, flat bedside table.

Operation

Lamp Controls

• Power Button: Press to turn the lamp on or off.
• Preset Button:
  • Slide along the edge of the button to adjust brightness.
  • Press the button to switch between color presets.

Install Mi Home App

To unlock advanced features and control the lamp remotely, install the Mi Home app:

1. Scan the QR code (QR code excluded from output) or search for "Mi Home" in your device's app store and install the application.
2. Turn on the lamp, open the Mi Home app, and follow the on-screen instructions to connect the lamp.

* Ensure your Wi-Fi network is available and can access the internet properly for app connectivity.

Advanced Features

Delayed Power Off

Hold the power button until the light starts breathing, then release. The lamp will switch off automatically.

* By default, the lamp will switch off in 15 minutes. This delay can be adjusted within the Mi Home app.

Adjusting Colors

Slide along the edge of the preset button while holding it to adjust the lamp's colors.

* This action adjusts the current color and does not change the saved color presets.

Factory Reset

To reset the lamp to its factory settings, press and hold both the power button and the preset button simultaneously for 5 seconds. The light will cycle through red, green, and blue, and the lamp will reboot.

* Perform a factory reset and reconnect the lamp if you are using a new Wi-Fi network.

Compliance and Warnings

FCC Compliance Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Warnings

• Suitability for use "indoors"; the related ambient temperature is 77°F (25°C).
• Use the correct power source.
• Cut off the power before opening the cover or replacing the bulb.
• If in any doubt, consult a qualified electrician.
• Do not place the luminaire on an inclined plane.
• ? For household use only.
• [Class II Symbol] Class II luminaire.
• ♻️ Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities. Contact your local government for information regarding available collection systems. Improper disposal can lead to hazardous substances leaking into groundwater and the food chain, damaging health and well-being.
• If the power cord is damaged, it must be replaced by the manufacturer or a qualified service engineer to avoid safety risks.
• The LED module cannot be replaced.
• Do not disassemble the product. The light-emitting diode may cause damage to your eyes.

Features

• ? 16 million colors
• ?️ Adjustable color temperature (1700-6500 K)
• ? Night light mode
• ☀️ Adjustable brightness
• ? Touch controls
• ?️ Eye care mode
• ?️ Presets
• ? Adjustable colors
• ⏰ Timer function
• ⏳ Off-delay timer
• ? Control via Mi Home app
• ⬆️ Firmware updates

Specifications

Manufacturer Information

Read this manual carefully before using the product.

For more information, visit www.mi.com.

Manufacturer: Qingdao Yeelink Information Technology Co., Ltd. (a Mi Ecosystem Company)

Address: 10F-B4, Building B, International Innovation Park, 1 Keyuan Weiyi Road, Laoshan, Qingdao, Shandong Province, China