Mi Computer Monitor Light Bar

Product Overview

Read this manual carefully before use, and retain it for future reference.

Components:

• Light Bar
• Base
• Type-C Charging Cable
• Remote Control

Diagrams:

• Illustration showing the light bar with power contact points and base.
• Illustration showing the remote control and its components (knob, battery compartment).

Installation

1. Install the light bar

• Attach the power contact points on the light bar to those on the base, with the light area facing downwards.
• Place the base on the upper center of the monitor, ensuring the clamp is firmly secured and the bottom of the base is against the back of the monitor.

Notes on Monitor Compatibility:

• Compatible with monitors up to 32 mm thick, including hairtail, curved, and iMac monitors.
• Monitors less than 10 mm thick are supported, but the base may not rest against the monitor.
• The gravity shaft angle on the base is adjustable by 40°. Do not force it.
• Not compatible with laptops.

2. Install the remote control batteries

1. Open the back cover of the remote control by placing it face down, holding it, and turning it counterclockwise.
2. Install two AAA batteries (sold separately), ensuring correct polarity (+/-).
3. Replace the back cover, aligning the triangle with the lock symbol.
4. Secure the back cover by turning it clockwise.

How to Use

1. Connect to power supply

• Connect the Type-C charging cable to the power port on the light bar and plug it into a power supply.

Power Supply Requirements:

• Requires a 5V output voltage and >1A output current power supply (adapter, power bank, or computer USB port).
• Power supplies must be Safety Extra Low Voltage (SELV) with a peak voltage not exceeding 5.25V.
• Use the original charging cable. Avoid USB extension cables or splitters.
• Do not use fast charging adapters that do not default to 5V.
• If the light flickers or makes noise, replace the power supply.
• Do not connect power contact points to other conductors.
• The original cable does not support fast charging or data transmission.

2. Control the light

• On/Off: Press the knob on the remote control.
• Brightness: Rotate the knob.
• Color Temperature: Press and hold the knob while rotating it.
• Preset: Press and hold the knob for two seconds for optimal computer lighting (2700K, 50% brightness).

Pairing: The remote and light bar are pre-paired. For re-pairing, press and hold the knob within 20 seconds of powering on the light until it blinks slowly.

3. Adjust the angle

Rotate the light bar to adjust its angle. It has an adjustment range of 25°.

Specifications

• Model: MJGJD01YL
• Operating Temperature: -10°C to 40°C
• Operating Humidity: 0-85% RH
• Service Life: 25,000 hours
• Rated Power: 5 W (80 x 0.2 W/LED module)
• Light Bar Dimensions: 23 x 448 mm
• Remote Control Dimensions: 66.5 x 34 mm
• Color Temperature: 2700-6500 K
• Color Rendering Index: Ra95
• Luminous Flux: 270 lm
• Rated Input: 5V=1A
• Wireless Connectivity: 2.4 GHz
• Operating Frequency: 2405-2470 MHz
• Maximum Output Power: 7.94 dBm

Precautions

• One remote can control multiple light bars, but a light bar is controlled by only one remote.
• Clean the light bar surface with a soft cotton cloth; avoid corrosive solvents.
• When installing or moving, handle both the light bar and base together to prevent damage or injury.
• Ensure correct battery polarity in the remote control.
• Do not recharge non-rechargeable batteries. Do not mix battery types or old/new batteries.
• If the remote malfunctions, replace batteries. Dispose of old batteries according to local regulations.
• Remove batteries if the remote is not used for a long time or is disposed of.
• Handle leaking batteries according to local regulations.
• The light source should only be replaced by the manufacturer, service agent, or qualified personnel.
• For indoor use only.
• Maintain at least 20cm separation distance between the antenna and user body during normal operation.

CE EU Declaration of Conformity

Qingdao Yeelink Information Technology Co., Ltd. declares that the radio equipment type MJGJD01YL complies with Directive 2014/53/EU. The full declaration is available at: https://www.mi.com/en/service/support/declaration.html.

WEEE Disposal and Recycling

This symbol indicates WEEE (Waste Electrical and Electronic Equipment). Dispose of this product at designated collection points to prevent negative environmental and health consequences. Contact local authorities for more information.