IJOY Elite Mini Kit

Introduction

Thank you for choosing IJOY! Please read this manual carefully to ensure proper use. For additional information regarding this product or its use, please consult your local IJOY retailer or visit our website www.ijoycig.com.

The Elite Mini Kit is the evolution of the IJOY RDTA Box mini platform, capable of firing up to 60W with a built-in 2200mAh Li-Po battery, while retaining the versatile foundational form factor. It is sleek and portable. This is a new compact all-in-one kit that integrates three different vape styles into one chassis. Included with each kit is an IJOY RDTA Box mini mod, an IJOY Captain Elite SUBOHM&RTA Tank, and an IJOY J&P Pod Adapter, which extends ultimate flexibility in one device.

The Elite Mini Kit aims at providing ease of use, a rich flavor ecosystem, and ultimate flexibility. It is a wonderful kit for entry-level to enthusiast-level vapers.

Standard Configuration:

• 1x IJOY BOX MINI (2200mAh) Mod
• 1x IJOY Captain Elite SUBOHM&RTA Tank
• 1x J&P Pod Adapter
• 1x Manual
• 1x USB Cable
• 1x Warranty Card

Device Overview

The device features a compact design with the following dimensions:

• Height: 74.7mm
• Width: 45mm
• Depth: 25mm

Key components are labeled as follows:

• ① Fire Button: The primary button for activating the device.
• ② OLED Screen: Displays device status, settings, and information.
• ③ '-' Button: Used for decreasing values or navigating menus.
• ④ '+' Button: Used for increasing values or navigating menus.
• ⑤ Micro USB Port: For charging and firmware upgrades.

Specifications

Operation Instructions

1. Power On/Off

Press the fire button 5 times in quick succession to turn the device on and off. After switching on, the OLED display shows the BOX mini logo and software version number in standby mode.

Note: Please adjust the wattage to a proper range to match the atomizer you used before using.

2. Vaping

While the device is powered on, press and hold the fire button to vape. The firing timeout is 10 seconds. While the device is powered on, the OLED screen defaults to displaying VW Mode.

3. General Functions

To enter the Main Menu, press the fire button 3 times. Use the right and left buttons to switch among different functions. Press the fire button to confirm your selection.

• P: Variable Wattage mode
• T: Temperature Control Mode (NI/TI/SS/M1/M2)
• TCR: TCR settings
• Set: Settings for LED, Puff counter, and Screen time.

4. Power Mode (VW)

In the main menu, switch to the "P" setting and press the fire button to confirm. Use the right and left buttons to adjust the wattage.

Intensity Setting in Power Mode

In the main menu, switch to the intensity setting, press the fire button to confirm. Press the right and left buttons to switch among 4 modes:

• Norm Mode: Maintains the currently set power.
• Hard Mode: Provides 30% higher power than the currently set power.
• Soft Mode: Provides 20% lower power than the currently set power.
• User Mode: Allows customization of power output for the first three seconds of each puff. Each setting column represents half a second.

To set User Mode, navigate to the User Mode option, press the fire button to confirm. The screen displays energy bars representing time segments. Adjust the power level for each segment using the +/- buttons. Press the fire button to move to the next segment, and confirm your final settings.

5. Temperature Control (TC) Mode

In the main menu, switch to the "T" setting, press the fire button to confirm. Press the right and left buttons to switch among NI, TI, SS, M1, and M2 modes. Press the fire button to confirm your selection.

• Adjusting Wattage: Press the '+' button. The 'W' symbol will flash. Use the +/- buttons to adjust wattage. Press the fire button to confirm.
• Adjusting Temperature: Press the '-' button. The '°F' or '°C' symbol will flash. Use the +/- buttons to adjust the temperature. Press the fire button to confirm.

The temperature unit will cycle between °F and °C when the minimum or maximum temperature is reached. For example, holding the button after reaching 600°F will cycle to 150°C.

6. TCR Mode (M1, M2)

The TCR (Temperature Coefficient of Resistance) function allows you to customize your temperature control coils (NI, TI, SS). In the main menu, switch to the "T" setting, press the fire button to confirm. Switch to M1/M2 modes and press the fire button to confirm.

How to set the TCR: In TCR mode, press the fire button to select TCR M1 or TCR M2. Use the right/left buttons to adjust the parameter value. After setup, press the fire button to switch to "EXIT". Press the right or left button to confirm.

When replacing the heating wire in temperature control mode, if the resistance difference between the new and previous wire is greater than or equal to 0.2ohm, the screen will display prompts. Use the '+' button to select and confirm the new coil resistance, or the '-' button to select and confirm the same coil resistance.

7. Puff Counter

In any mode, the screen displays the number of puffs. A puff is recorded if its duration exceeds 0.8 seconds. The device remembers the puff count even if the battery is removed. The default count is "000". When the count reaches "999", it will automatically reset to zero.

How to manually clear puff history: Press the fire button 3 times within 2 seconds to enter the menu. Select the 'Set' icon, then choose the 'PUFF rest' option, and press the fire button to confirm your choice.

8. Set POD Mode

Press the fire button 3 times within 2 seconds to enter the menu. Select the 'Pod' icon to enter POD Mode. In this mode, the output wattage can be adjusted in the range of 5-12W.

9. Set Standby Mode (Screen Timeout)

Press the fire button 3 times within 2 seconds to enter the menu. Select the 'Set' icon, use the '+' and '-' buttons to choose the "Screen Time" option. There are 4 preset choices (5s, 10s, 15s, 30s). Press the fire button to confirm your choice; the screen will enter standby mode after the selected time.

10. How to Calibrate Resistance?

When the device is connected with a new atomizer, press the '+' and '-' buttons simultaneously to calibrate the initial resistance of the new atomizer. It is recommended to calibrate resistance in temperature control mode for more accurate results. Please ensure the heating wire has cooled to room temperature before calibration.

11. USB Upgrade Operation

Connect the device to a computer via a USB cable. Press and hold the '+' and '-' buttons together, then press the fire button simultaneously to enter the upgrade process. Release the '+' and '-' buttons first, then release the fire button. Upload the latest firmware using the PC software. Once the upgrade is complete, press the '+' and '-' buttons to reset the device. The device can then work properly.

12. How to Charge by USB?

When the voltage is lower than 3.3V, the display will show "Low Battery". Connect the device via the USB cable to a computer or power adapter to charge.

• During charging, the red indicator light is bright; it turns off when fully charged.
• If the battery voltage drops below 3.2V during charging, the device will turn off.
• Vaping is not allowed during charging.

Note: If the device is not used for a long time, please charge it every 30 to 60 days to maintain battery life.

13. Malfunction Indication and Protection

The device includes several protection features:

• PCB Overheat Protection: If the device's internal temperature becomes too high, the output will automatically shut off, and the screen will display "PCB TOO HOT".
• Low Battery Alert: When the battery voltage is below 3.2V, the device displays "LOW BATTERY". The battery should be removed and charged.
• Atomizer Short-Circuit Protection: If a short circuit occurs in the atomizer, the OLED screen will display "SHORTED".
• No Atomizer Detection: If the device is used without an atomizer connected, it will display "No atomizer".
• Low Resistance Protection: If the atomizer resistance is lower than 0.06ohm, the system will automatically cut off output, and the OLED screen will display "OHMS TOO LOW".
• High Resistance Protection: If the atomizer resistance is higher than 3ohm, the system will automatically cut off output, and the OLED screen will display "OHMS TOO HIGH".

Warnings

Do Not Use Battery with Broken Wraps

Avoid using batteries with damaged or missing insulation wraps. Ensure the positive and negative poles have proper insulation.

General Warnings:

1. Please read the user manual carefully before use.
2. If the device will not be used for an extended period, please remove the atomizer to prevent e-liquid from leaking into the device.
3. If the device will not be used for a long time, please remove the battery and store it in a dry, cool place.
4. Keep the device away from children, pregnant women, and minors under 18 years of age.