ZigBee Smart Switch Instruction Manual

Product Description

This new designed smart switch with 1/2/3 gang optional is designed with ZigBee protocol to replace traditional switches with a variety of ways to control. One switch for two wirings optional (N+L wire / only L wire) and a ZigBee hub is required for normal use. A new smart feature, multi-control association (only for N+L wire), is added for other smart switches in the Smart Life/Tuya App, and all controlling modes work without any interference. Its design is suitable for different decoration styles with its best value.

Safety Information

Risk of Electric Shock: Electricity can cause personal injury and property damage if handled improperly. If you are not sure about any part of these instructions, please seek professional assistance from a qualified electrician.

Warnings: Turn off the power at the circuit breaker and test that power is off before wiring.

Technical Parameters

Installation

Note: Make sure that the power at the circuit breaker is off before wiring. Two versions are available: Neutral wire required and no neutral needed. Please make the correct wiring according to the switch you purchased. If your wall box does not contain a Neutral Wire, please try another location or call a professional electrician. Wire colors may differ from manual. Ensure wire conductors are securely fastened. Ensure Wi-Fi signal is steady and your mobile and Zigbee gateway hub are under the same 2.4GHz WiFi network. If you lack wiring experience, call a professional.

Step 1: Turn off the power

Turn off the circuit breaker and use an electrical tester to verify power is off before wiring.

Step 2: Remove the old switch

Remove the old switch and pull it away from the wall.

Step 3: Identify wires

Identify Line/Load wires. Note: Wire colors may differ from the manual.

Verify power is off: Remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage. You may need to turn off more than one circuit breaker.

Step 4: Take pictures of the wiring

Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.

Step 5: Mount the switch

Mount the switch with the provided screws and snap the wall plate on it.

Step 6: Restore power

Turn the power back on at the circuit breaker and then switch the light on.

Add Devices

1. Download Smart Life App

Please scan the QR code or download the Smart Life app from your app store.

2. Registration or Log in

Download the "Smart Life" Application. Enter the Register/Login interface; tap "Register" to create an account by entering your phone number to get a verification code and set a password. Choose "Log in" if you already have a Smart Life account.

3. Configure the APP to the switch

Preparation: Ensure the switch is connected to electricity; ensure your phone is connected to Wi-Fi and can connect to the Internet. Note: If you have connected to a 5G network, please disconnect it first and connect to a 2.4G network.

3.1 ZigBee link method: Re-pair and clear ZigBee code

Press and hold the button for about 7 seconds, until the blue indicator on the switch flashes rapidly after 3 seconds. Repair is successful.

Open the App, select "+" on the top right, choose "Switch (Zigbee)" to add the device. Select the right Gateway to confirm the connection.

How to Reset/Re-pair ZigBee code: Press and hold the button for about 7 seconds, until the blue indicator on the switch flashes fast after 3 seconds. Reset/Re-pair is successful.

3.2 How to achieve multi-control association (only for N+L wire)

Note: Please confirm you have successfully finished the link method above for adding this switch to your Smart Life App before association.

1. Add another smart switch to the same Smart Life/Tuya App. (If a smart switch has already been added, proceed to the next step.) Note: If your switch requires a neutral wire, it does not need to be wired to the light; only L and N are required for wiring. This allows controlling one light with multiple switches. If your switch does not require a neutral wire, follow wiring instructions to connect L and the light. This enables simultaneous control of lights with multiple switches.

2. You will see two devices in the app. Click the main switch (acting as a single gang switch) to proceed.

3. Click the "+" icon in the upper right corner and choose "Multi-Control Association", then click "+" again in the right corner.

4. Choose the switch you want to associate and then select the switch button that will control the same light.

5. Return to the previous page; you will see two items: your main switch and the associated switch. Note: Please confirm the associated switch is enabled.

6. You can now control your light with two switches. Do not associate another button on the same switch for multi-control.

7. To add a third or more smart switches, repeat the steps above. The result will show multiple associated switches.

Enter Smart Life Skill in Alexa APP

1. Complete product networking configuration in the App

Complete the device's networking configuration according to the prompts in the App. Note: In the App, change the device name to an easily identifiable name, such as "bed light" (names are usually in English).

2. Configure the Amazon Echo device

(If you have already configured Amazon Echo, you can skip this step.) Make sure your Amazon Echo device is powered on and connected to a Wi-Fi network.

Open the Alexa App on your phone. After successful login, tap the menu in the upper left corner, select "Settings", and tap "Set Up A New Device" to configure Amazon Echo.

Choose your Amazon Echo device type and language. Press and hold the small dot on the device until the light turns yellow. Tap "Continue" to connect to the hotspot.

After connecting to the Amazon Echo hotspot, return to the page. The connection is successful.

Tap "Continue" to proceed. Choose a Wi-Fi network. Amazon Echo will take a few minutes to connect. After successful connection, tap "Continue". An introduction video will play. Tap "Continue" to go to the Alexa Home page.

3. Key step ---- Link Skill

Tap "Skills" in the Alexa App menu.

Search for "App Name" (referring to Smart Life). Tap "Enable" to activate the Skill.

Enter your App account and password, then tap "Link Now" to link your App account and enable the Skill. You can now start your smart home journey.

4. Common commands

Control the device via voice commands with Echo. Examples:

• "Alexa, turn on/off bedroom light."
• "Alexa, set bedroom light to 50 percent."
• "Alexa, brighten/dim bedroom light."
• "Alexa, set bedroom light to green." (Adjusts color)

Service

1. During the free warranty period, if the product breaks down during normal use, free maintenance will be offered.
2. Service is not provided for natural disasters/man-made equipment failures, disassembly and repair without company permission, products beyond the free warranty period, etc.
3. Any commitment made by a third party (including dealer/service provider) to the user beyond the warranty scope will be executed by that third party.
4. Please keep this warranty card to ensure your rights.
5. The company may update or change products without notice. Refer to the official website for updates.

Warranty Card

Recycling Information

All products marked with the WEEE symbol must be disposed of separately from municipal waste. To protect health and the environment, this equipment must be disposed of at designated collection points. Correct disposal and recycling help prevent negative consequences for the environment and human health. Contact your installer or local authority for information on collection points.

Maintenance Records