AQQA AQ147 User Manual

1. PRODUCT FEATURES

• Professional Down Light: Adopt high-quality COB LED full-spectrum lamp beads; the measured temperature will reach 5000K+. It has superior light penetration and is transparent and bright enough to lighten the whole tank easily.
• Multifunctional Controller: 3 Light colors: full-spectrum, white, and colored light; 6 brightness levels: 10%, 30%, 50%, 70%, 90%, 100%; 3 timing functions: 6H, 10H, 12H. Multiple control methods to meet a variety of usage requirements.
• High-temperature Cooling: Noise-reducing fan for heat dissipation, one-piece aluminum alloy fan system, grid-like wire channel design, 360° annular curved screen blade, greatly increase the cooling surface, effectively reduce light decay.
• Solid Bracket System: The aluminum alloy clip design allows for the freedom of height and front and back distance. It is easy to adjust the light distance and meet different fish tanks and light areas.

2. PRODUCT PARAMETER

3. PRODUCT STRUCTURES

The product consists of a down light, power cord, clamp, cable clip, bracket, and controller.

Controller Functions:

• Timer button [TIMER]: The light automatically lights up when connected to the power supply. Long press for 3 seconds to turn off, then long press for 3 seconds to turn on again.
• Light color conversion button [M]: Offers 3 colors: full-spectrum, white, and colored light. Pressing the button cycles through different light colors.
• Light brightness button: Features 6 adjustable brightness levels: 10%, 30%, 50%, 70%, 90%, and 100%. Each press cycles through different brightness levels.
• Timer button: Provides 3 timed periods: 6H, 10H, and 12H. After selecting light color and brightness, press this button to choose the desired duration.

Example of Timer Function: If the light color is full-spectrum, brightness is 50%, and timing is set to 6H (e.g., starting at 14:00 local time), the light will operate for 6 hours and turn off at 20:00. It will then automatically turn on the next day at 14:00, gradually brightening to 50% over 4 minutes before 14:04, allowing fish to adapt.

4. INSTALLATION STEPS

1. Attach Light Bracket: Use the included Allen wrench to tighten the light bracket using flat-head screws.
2. Secure Tank Bracket: Fasten the clip to the bracket using the Allen wrench with dome-head screws.
3. Install Light Body: Screw the light body onto the bracket by hand until snug.
4. Plug in Controller: Connect the light to the controller.
5. Mount on Tank: Position the assembled unit on the fish tank and tighten to secure.
6. Organize Cables: Use cable clips to fix wires in place.

Dimensions:

• Light body diameter: 12cm/4.7 inches
• Height: 20.5 inches
• Adjustable bracket width for tank rim: 11.8-14.6 inches
• Bracket clamp opening: 0.4-2.0cm/ 0.16-0.78inch
• Light body height: 5.5 inches
• Bracket height adjustment: 18cm/7 inches

5. ATTENTIONS

• Please read this user manual carefully before using and follow it strictly.
• Keep the switch away from water as it is not waterproof.
• Keep the light away from flammable items to avoid accidents.
• Unplug the power and contact the seller if the light is not working properly. Opening the unit will void the warranty.
• Unplug the power before maintenance.
• The operating temperature range for the light is between 23°F~113°F (-5℃~45℃).

6. WARNING

• To avoid possible electric shock, do not immerse the switch in water. If the switch falls into water or becomes wet, do not touch it until unplugged.
• DANGER: Special care is needed due to water use in aquarium equipment. Do not attempt self-repair. Return to an authorized service facility for maintenance or disposal.
• If the light falls into water, DO NOT touch it. Unplug it first, then retrieve it. If electrical components get wet, unplug immediately.
• Examine the light carefully after installation. Do not plug in if water is on non-intended parts.
• Do not operate with a damaged cord or plug, or if malfunctioning, dropped, or damaged. The power cord is non-replaceable; if damaged, the light must be discarded.
• To prevent the plug or outlet from getting wet, position the aquarium and stand to the side of a wall outlet to prevent dripping. Arrange a "drip loop" for each cord connecting the light to the outlet. If an extension cord is used, the "drip loop" is the part of the cord below the outlet level that prevents water from traveling along the cord to the outlet. If the plug or outlet gets wet, DO NOT unplug. Disconnect the circuit breaker supplying power. Then, unplug and examine the outlet for water. Consult an electrician if unsure.
• Close supervision is necessary when the light is used near children.
• Do not contact moving or hot parts to avoid injury.
• Ensure the light is securely installed before operating.
• Read and observe all important notices on the light.
• If an extension cord is necessary, use one with a proper rating (amperes or watts). A cord rated lower than the appliance may overheat. Arrange the cord to prevent tripping or pulling.
• The light is intended for HOUSEHOLD USE ONLY.
• SAVE THIS USER MANUAL.

7. AQQA LIMITED MANUFACTURER'S WARRANTY

AQQA offers a 2-year manufacturer warranty from the date of sale for products purchased from an AQQA®-authorised specialist dealer. Retain your receipt for warranty claims. Products are guaranteed against defective material and workmanship under normal use for up to 2 years from the original purchase date through an Authorized Dealer.

Products have no warranty if:

• The product has been serviced, modified, or tampered with by anyone other than AQQA® Aquatic Supplies.
• The product has been abused or damaged (including broken or cracked bulbs).
• The product was transported without proper packaging.
• The product was purchased from an Unauthorized Reseller.

WARRANTY LIABILITY DISCLAIMER: AQQA® is not liable for consequential or incidental damages, including lost aquatic life, personal injury, property damage, equipment damage, lost profits, lost wages, lost savings, or lost income arising from the use of AQQA® products.

Terms and Conditions of Warranty:

• AQQA® warrants for 2 years from the original purchase date through an Authorized AQQA® Reseller, offering free repair or replacement for faults due to defective materials or faulty workmanship.
• All claims must be made at the place of purchase.
• Only the direct purchaser can make warranty claims, and they are not transferable without consent.
• The original, dated Proof of Purchase (receipt) must accompany all claims. Provide this Guarantee where possible.
• Wear parts (seals, suction devices, axes, pump wheels, light sources, pH electrodes, filter media, filter cartridges, UVC burners), glass damage, product opening, structural changes, or use of non-AQQA® original parts are excluded from the guarantee.
• Goods for warranty claims must be prepared for transport in original or comparable packaging. AQQA® will not cover shipment costs.
• If inspection reveals goods are in normal working order, AQQA® may request reimbursement for reasonable costs.
• Warranty claims do not apply to insignificant deviations in color, dimensions, quality, or performance characteristics.
• The warranty obligation extends only to newly manufactured products. Used products are sold as-is, excluding any warranty, unless otherwise agreed.

8. DISPOSAL

Do not dispose of this product as unsorted municipal waste. It requires special treatment for recycling of electrical and electronic appliances at an authorized facility. Collecting and recycling waste saves natural resources. Consult your local seller for environmentally friendly disposal methods.

9. PACKING LIST

• 1x LED light
• 1x AC/DC adapter
• 1x Metal bracket arm
• 1x User manual

10. CONTACT INFORMATION

Company Name: Shenzhen Aiku Pet Technology Co., Ltd

Address: Room 501, No.20, Lane 1, Lishipai, Dafapu Community, Bantian Street, Longgang District, Shenzhen Guangdong. 518000

Email: service@aqqapet.com

Website: http://www.aqqapet.com

Follow AQQA on social media: Facebook, Instagram, YouTube @AQQA Aquarium

For any issues, please provide your Amazon order ID (Amazon invoice) and shipping address via email to service@aqqapet.com.

Regulatory Information

EC REP: E-CrossStu GmbH, Address: Mainzer Landstr.69, 60329 Frankfurt am Main, Email: E-crossStu@web.de, Nr.202504727907

UK REP: YH Consulting Limited, Address: C/O YH Consulting Limited Office, 147 Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX, Email: H2YHUK@gmail.com, Tel: +44 07514-677868, No.202504725766

CE, UK CA markings are present. Product is MADE IN CHINA.

Recycling symbols indicate proper disposal methods.