Feit Electric Smart Outdoor Camera

Important Safety Instructions and Installation Guide

READ BEFORE INSTALLATION - SAVE THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS:

ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT.

FCC STATEMENT

Supplier's Declaration of Conformity:

47 CFR § 2.1077 Compliance Information

Responsible Party: Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660, USA, 562-463-2852

Unique Identifier: CAM/WM/WIFI/BAT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. The device can be used in mobile (min 7.87 in.) exposure condition without restriction.

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please visit feit.com/help for instructions on replacement/refund or call 866.326.BULB. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

SD™, microSD™, and SDHC™ are trademarks or registered trademarks of SD-3C, LLC in the United States, other countries, or both.

Pre-Assembly

Tools Required to Mount Camera

• Phillips Screw Driver
• Pencil
• Power Drill

Hardware Included

NOTE: Hardware not shown to actual size.

Description

NOTE: Before installing, fully charge the battery using the provided USB Cord (BB) by plugging it into a power source.

Camera Components:

• Status Light: Indicates camera status.
• Microphone: Captures audio.
• Lens: Primary optical component.
• Photosensitive: Adjusts to light conditions.
• PIR: Passive Infrared sensor for motion detection.
• Speaker: Outputs audio.
• Reset: Button to reset the camera.
• Micro USB: Port for charging.
• Charging LED Indicator: Shows charging status.
• Power Button: Turns the camera on/off.
• SD Card Slot: For recording media.

Specifications:

• Input Power (Micro USB): 5VDC, Max. 1A
• Power Button: Press and hold for 3 seconds to turn On/Off the camera.
• Status Light:
  • Blinking RED = Pairing Mode
  • Solid RED = No Wi-Fi Connection
  • Blinking BLUE = Connecting to Wi-Fi
  • Solid BLUE = Connected to Internet
• SD Card Slot: Add 128GB or less microSD card to enable recording (not included). Only supports microSD card with FAT32 format.
• Reset: Press and hold for 5 seconds on the Reset button to reset the camera.
• Charging LED Indicator: Solid Red: Battery is charging; Solid Blue: Charging is complete.
• Battery Capacity: 9600mAh (contains two 21700 non-replaceable lithium-ion batteries).

Installation

Wall Mount Installation

1. Mark Screw Positions: Mark screw positions using the Adjustable Mounting Bracket (FF) on your wall.
2. Inserting the Mounting Anchors: Drill holes at the marked points if installing on a hard surface such as concrete or brick. Insert Mounting Anchors (DD) into holes. Skip this step if installing on wood or siding.
3. Attaching the Bracket: Use the Mounting Screws (CC) to attach the Adjustable Mounting Bracket (FF) to the wall.
4. Attaching the Camera: Push and hold the Power Button on the back of your Smart Outdoor Camera (AA) until it turns On. Twist the Smart Outdoor Camera (AA) onto the Adjustable Mounting Bracket (FF).
5. Adjust Camera: Adjust the camera angle as desired. Tighten the thumbscrew and white knob when finished. The adjustable mount provides 360° swivel and 90° of tilt.

Magnet Mount Installation

1. Mark Screw Positions: Mark screw positions using the Metal Mounting Bracket (EE) on your wall.
2. Inserting the Mounting Anchors: Drill holes at the marked points if installing on a hard surface such as concrete or brick. Insert Mounting Anchors (DD) into holes. Skip this step if installing on wood or siding.
3. Attaching the Bracket: Use the Mounting Screws (CC) to attach the Metal Mounting Bracket (EE) to the wall.
4. Attaching the Camera: Push and hold the Power Button on the back of your Smart Outdoor Camera (AA) until it turns On. Attach the Smart Outdoor Camera (AA) to the Metal Mounting Bracket (EE).

APP Setup

Download and Install the Feit Electric App

• Search for the Feit Electric app in the App Store or Google Play Store.
• Download and install the Feit Electric app on your smart device.

Set up the smart outdoor camera using the Feit Electric app

• Check to be sure the camera is in pairing mode. The RED indicator light must be blinking rapidly to connect. If not already blinking, press and hold the Reset Button until you hear an audible tone.
• Use the Feit Electric app to complete the set up. Tap Add Device or the + sign, then select Camera and confirm.
• You will be prompted to enter your Wi-Fi network and password.
• Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.

Troubleshooting

Need Help?

Thank you for your purchase. Questions, comments or feedback? We'd love to hear from you.

Visit feit.com/help for support or connect with us:

• Facebook: @FeitElectric
• Twitter: @FeitElectricInc
• Instagram: @feitelectriclighting