Feit Electric Flood Light Security Camera Installation Guide

Model: SEC3000/CAM

Installation Continued

9. Position Motion Sensor and Camera

For optimal performance, the base of the motion sensor should be placed parallel and 9 feet above the ground. The camera can be angled in a different direction than the lights. The motion detector is optimized to detect human-sized objects for up to 30 ft.

10. App Setup

Download and install the Feit Electric app from the App Store or Google Play Store.

Steps to set up the flood light camera using the Feit Electric app:

Ensure the flood light camera is in pairing mode (the blue indicator light must be blinking rapidly). If not, press and hold the Reset Button until an audible tone is heard.
Tap 'Add Device' or the '+' sign, then select 'Flood Light Camera' and confirm.
Enter your Wi-Fi network name and password. Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.

Optional Integrations:

Connect to Google Assistant or Alexa using the in-app guide. Tap the Pen icon, then choose Alexa or Google Assistant.
See the App User Guide to set up Siri Shortcuts.

Troubleshooting Tips - Q & A

Camera will not connect to my Wi-Fi network

Ensure the LED is blinking blue. If blinking red, press and hold the Reset Button (located behind the cover on the side of the camera) to reset.
Verify you are using a 2.4GHz network, as the device does not connect to 5GHz networks.
Test your Wi-Fi network with other devices to ensure it's operating correctly.
Check Wi-Fi range; at least 2 signal bars are recommended for a proper connection.
Ensure the Wi-Fi password is entered correctly (it is case-sensitive).

The camera is off-line

Check for temporary internet connection issues or service disruptions.
Ensure your Wi-Fi router is powered on.
Confirm the camera has power (wall switch and breaker are ON).
Cycle the power: turn it OFF and ON. The status LED should blink red then turn solid blue in about 1 minute. If not, repeat the setup process.
Ensure the camera has a good Wi-Fi signal (at least 2 bars recommended).
If disconnected, press and hold the Reset Button until a blinking blue LED and audible tone are heard.

What do the blinking LEDs mean?

Blinking BLUE = Pairing Mode
Blinking RED = No Wi-Fi Connection
Solid RED = Rebooting
Solid BLUE = Connected to Internet

Live video stream is slow to load

Check your phone's cellular connection strength.
Ensure sufficient internet bandwidth at home; other streaming services can cause congestion.
Verify Wi-Fi reception strength (at least 2 bars recommended). Consider a Wi-Fi repeater or extender if needed.

How to reset the camera to re-enter pairing mode?

Press and hold the reset button located behind the cover on the side of the camera until a blinking blue LED and an audible tone are heard.

The camera is not recording?

Ensure the 'Record Switch' is turned ON in the app under 'SD Card Settings'.
Verify the microSD card is installed correctly. Check 'SD Card Settings' in the app to confirm capacity information is displayed.
If issues persist, consider reformatting the microSD card (this will delete all videos).

How do I set the camera to Event or Continuous Recording?

In the Settings menu under 'SD Card Settings', ensure 'Record Switch' is ON, then select 'Event Recording' or 'Continuous Recording'.

How can I check the available space on the SD Card?

In the Settings menu under 'SD Card Settings', 'Used Space' and 'Free Space' are displayed. The camera supports microSD cards up to 128GB.

What happens when the microSD card reaches full capacity?

A notification will be sent when storage is almost full. Once full, new videos will overwrite the oldest ones.

Can I use a new microSD card if I do not want to record over existing videos?

Yes. Replace the existing microSD card (up to 128GB) with a new one. Format the new card via 'SD Card Settings' in the app by pressing 'Format SD Card' and confirming. Note: Formatting deletes all content.

Installation Instructions

WARNING:

This product may represent a possible shock or fire hazard if improperly installed. Install in accordance with the owner's manual, current electrical codes, and/or the National Electric Code (NEC). RISK OF ELECTRIC SHOCK: TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING.

Parts Included:

1. J-Box (not included)
2. Mounting Bar
3. J-Box Screws (2 pieces)
4. Spacers (2 pieces)
5. Mounting Gasket
6. Mounting Plate
7. Terminal Block
8. Mounting Plate Screws (2 pieces)
9. Mounting Bar Screw (1 piece)
10. Fixture Body
11. Mounting Holes
12. Rubber Washers (2 pieces)
13. Decorative Nuts (2 pieces)
14. LED Flood Lights
15. Camera Lens and Photocell Sensor
16. Speaker
17. Motion Sensor
18. Mic
19. Indicator Light

Tools Required (not included):

Sealant

External J-Box Installation:

Turn main power OFF at the circuit breaker or fuse box.
Install Mounting Bar (2) to an External J-Box (1) using J-Box Screws (3). Add Spacer (4) if needed to eliminate gap between Mounting Bar and Mounting Plate.
Feed J-Box wires through openings on Mounting Gasket (5) and Mounting Plate (6). Tear away perforation on Mounting Gasket (5) as needed.
Secure Mounting Gasket (5) and Mounting Plate (6) to Mounting Bar (2) using Mounting Bar Screw (9). Do not over-tighten.
Connect power supply wires directly to Terminal Block (7): Black wire to 'L', Ground wire to 'GND', White wire to 'N'. Use a small flat-head screwdriver to secure wires.
Align Mounting Holes (11) on Fixture Body (10) to the Mounting Plate Screws (8). Secure Fixture Body (10) to Mounting Plate (6) using Rubber Washers (12) and Decorative Nuts (13).
Turn power ON at the circuit breaker or fuse box. Ensure lights work.
Apply silicone sealant around the base of the fixture to prevent moisture from reaching connections.

Flush J-Box Installation:

Turn main power OFF at the circuit breaker or fuse box.
Install Mounting Bar (2) to a Flush J-Box (1) using J-Box Screws (3). Add Spacer (4) if needed.
Feed J-Box wires through openings on Mounting Gasket (5) and Mounting Plate (6). Do not tear away perforation on Mounting Gasket (5).
Secure Mounting Gasket (5) and Mounting Plate (6) to Mounting Bar (2) using Mounting Bar Screw (9). Do not over-tighten.
Connect power supply wires directly to Terminal Block (7): Black wire to 'L', Ground wire to 'GND', White wire to 'N'. Use a small flat-head screwdriver to secure wires.
Align Mounting Holes (11) on Fixture Body (10) to the Mounting Plate Screws (8). Secure Fixture Body (10) to Mounting Plate (6) using Rubber Washers (12) and Decorative Nuts (13).
Turn power ON at the circuit breaker or fuse box. Ensure lights work.
Apply silicone sealant around the base of the fixture to prevent moisture from reaching connections.

Adjusting Fixture:

The flood lights and camera can be adjusted side to side, and up and down. The flood light carousel can also be adjusted side to side.

Pre-Installation:

Remove the Mounting Plate (6) by unscrewing and removing the Decorative Nuts (13) and Rubber Washers (12).

Resetting Unit & Accessing SD Card:

To access the Reset Button and microSD™ card, remove the cover using a small screwdriver. To reset the unit (while connected to power), press the Reset Button for 15 seconds or until an audible tone is heard. To remove the microSD card, push the card in with your finger and release; it will eject halfway.

Important Information

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirements and can be used in portable or mobile exposure conditions without restriction.

Limited Warranty:

This product is warranted to be free from defects in workmanship and materials for up to one year from the date of purchase. For warranty service, contact Feit Electric at info@feit.com, visit feit.com/contact-us, or call 1-866-326-BULB (2852). Replacement or refund is your sole remedy. Implied warranties are limited in duration to the duration of this warranty. Liability for incidental or consequential damages is expressly excluded.

Trademarks: SD™, microSD™, and SDHC™ are trademarks of SD-3C, LLC.

Features:

Only supports 2.4GHz Wi-Fi Networks
Works with Feit Electric app
ETL Listed

	LED Smart Security Flood Lights with Camera \| SEC3000/CAM/WIFI Discover the SEC3000/CAM/WIFI LED Smart Security Flood Lights with Camera. Features Wi-Fi connectivity, 128GB SD card storage, two-way audio, and motion sensing for enhanced home security.
	Feit Electric App User Guide for Flood Light Security Camera Comprehensive user guide for the Feit Electric App, detailing the setup and operation of the Flood Light Security Camera. Learn how to connect to Wi-Fi, register your device, and utilize features like motion detection, night vision, and two-way communication. Includes instructions for integrating with Siri Shortcuts, Alexa, and Google Assistant.
	Feit Electric Smart Indoor Camera CAM/PAN/WIFI Installation and Safety Guide Comprehensive installation guide and safety instructions for the Feit Electric CAM/PAN/WIFI Smart Indoor Camera. Learn how to set up, troubleshoot, and use features like Wi-Fi connectivity and SD card recording.
	Feit Electric Outdoor Battery Powered Smart Wi-Fi Camera Specifications and Features Detailed specifications and features for the Feit Electric Outdoor Battery Powered Smart Wi-Fi Camera (CAM-WM-WIFI-BAT), including connectivity, performance, and physical attributes.
	Feit Electric Smart Outdoor Camera Installation and Safety Guide This guide provides essential safety instructions, installation steps for wall and magnet mounts, app setup, and troubleshooting for the Feit Electric Smart Outdoor Camera (Model: CAM/WM/WIFI/BAT).
	Feit Electric Smart Dual Lens Panoramic Floodlight Camera SEC5000CAM2 Installation and Troubleshooting Guide Comprehensive guide for installing and troubleshooting the Feit Electric SEC5000CAM2 Smart Dual Lens Panoramic Floodlight Camera. Covers app setup, Wi-Fi connection, LED indicators, recording settings, and FCC compliance.
	Feit Electric Smart Video Doorbell Specifications Detailed specifications for the Feit Electric Smart Video Doorbell, including features like 1080p HD video, two-way audio, motion detection, and Wi-Fi connectivity.
	Feit Electric Smart Outdoor Camera Installation Guide and Safety Instructions Comprehensive guide for installing and setting up the Feit Electric Smart Outdoor Camera (Model: CAM/WM/WIFI/BAT). Includes important safety precautions, pre-assembly steps, wall and magnet mount installation, app setup instructions, and troubleshooting tips.