Shark Cordless POWERDETECT™ Vacuum IP1000 Series Quick Start Guide

Assembly

Follow these steps to assemble your vacuum:

1. Slide the Wand onto the neck of the Floor Nozzle until it clicks into place.
2. Align the Hand Vacuum nozzle opening with the top of the wand and slide it on until it clicks into place.

Ensure all components are completely connected and clicked for proper operation.

Diagram Description: Visual shows the handheld vacuum unit connecting to the MultiFLEX wand, which then connects to the floor nozzle. Connection points are indicated with "Click" labels.

Charging

Power On/Off

Press the On/Off button on the handle to turn the vacuum on or off.

Mode Selection

Use the mode selection trigger to toggle between ECO, DETECT, and BOOST modes.

Battery Charging

Charging the Battery in the Handheld Vacuum: Connect the charger to an electrical outlet, then insert the charger plug into the port located below the handle on the handheld vacuum.

Diagram Description: Visual indicators for battery charge status: a fully illuminated battery icon for 'Full Charge', a half-illuminated icon for 'Half Charge', a partially illuminated icon for 'Low Charge', and an empty icon for 'No Charge'.

Notes:

• An extra battery and charger may be purchased from sharkclean.com.
• The unit comes with a partial charge. For maximum runtime, charge fully before first use (approximately 6 hours). Leaving the unit plugged in will not damage battery life.

Modes Explained

• ECO MODE: Maximizes runtime.
• DETECT MODE: Senses your environment to optimize your cleaning experience. Detect technology is activated automatically when the unit is in use.
  • Dirt Detect: Identifies dirtier, high-traffic areas and automatically boosts suction power.
  • Floor Detect™: The brushroll responds to surface changes and automatically adjusts to optimize your clean.
  • Light Detect™: Senses low-light situations and automatically illuminates dark areas to help you spot debris.

Diagram Description: A visual representation of Detect Mode's functionality. It shows different floor conditions (Clean Floor, Medium Dirt, Heavy Dirt) corresponding to suction levels (Low Suction, Medium Suction, High Suction). It also highlights "Edge Detect" functionality, which dynamically detects edges and corners. A note indicates that the Hand Vacuum UI and Nozzle Lights are synchronized.

BOOST MODE: Maximizes suction.

Multiflex® and Storage

Multiflex®

If your vacuum model includes the MultiFLEX wand, you can adjust its angle to clean under furniture and in other hard-to-reach areas. Press the latch on the back of the wand to adjust the angle. To return to the original angle, straighten the wand until it clicks securely into place.

Flex Storage

Press the MultiFLEX latch on the back of the wand and fold the vacuum down into its storage position. Please ensure the vacuum dust cup is empty before storing.

Emptying the Dust Cup

To empty the dust cup, hold the handheld vacuum at a 45-degree angle over the trash. Press the latch on the front of the hand vac; the dust cup will drop open, releasing dust and debris. To close, push the dust cup back into place.

Diagram Description: Illustration depicting the process of emptying the dust cup, showing the dust cup opening to release debris.

Important: Filter Cleaning

Follow these steps to clean the HEPA filter:

1. To access the HEPA filter, press the dust cup empty button to release the dust cup.
2. Grip the filter by the tab and slide it out of the hand vac.
3. After the filter has been rinsed and air-dried completely (up to 48 hours), slide it back into the hand vacuum.

Notes:

• Rinse the HEPA filter at least once a month to maintain suction power. More frequent cleaning may be necessary with heavy use.
• To clean the filter, rinse it with water only and allow it to air-dry completely for up to 48 hours before reinstalling. Tap off loose dirt between washes when needed.
• IMPORTANT: DO NOT use soap when cleaning the filters. Use water only.
• The vacuum will not have suction if the post-motor filter is not installed. Ensure that all filters are installed before using.

Diagram Description: Diagrams illustrating the steps for accessing and cleaning the HEPA filter: releasing the dust cup, gripping and sliding out the filter, and reinserting the clean, dry filter.

Important Safety Instructions

WARNING: TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL. HOUSEHOLD USE ONLY.

When using an electrical appliance, basic precautions should always be followed, including:

• Inspect all parts for damage before each use. Discontinue use if any part is damaged.
• Use only identical replacement parts.
• Do not use the vacuum for purposes other than those described in the manual.
• Keep appliance and cord away from children. Do not allow children to use or play with the appliance.
• Do not expose parts (except filters/dust cup) to water or liquids.
• Always turn off the vacuum before connecting or disconnecting electrical or mechanical parts.
• Do not handle the plug or vacuum with wet hands.
• Ensure dust cup, HEPA and pre-motor filters, and brushroll are in place before use.
• Use only Shark® branded filters and accessories.
• Do not put objects into nozzle or accessory openings; keep openings clear of dust, lint, hair, and anything that may reduce airflow.
• Do not use if nozzle or accessory airflow is restricted. Turn off and remove obstructions if air paths or floor nozzle become blocked.
• Keep openings away from hair, face, fingers, uncovered feet, or loose clothing.
• Use extra care when cleaning on stairs.
• Do not leave the vacuum unattended while powered on.
• Keep the vacuum moving over carpet surfaces to avoid damage.
• Do not place the vacuum on unstable surfaces.
• Do not use to pick up liquids, large objects, sharp objects, large quantities of dust (including drywall, fireplace ash, embers), smoking or burning objects, flammable materials, or toxic materials.
• Do not use in poorly lit, wet/damp, outdoor, or enclosed spaces with explosive/toxic fumes or vapors.
• Turn off the vacuum before plugging in or unplugging the charger, or before any adjustment, cleaning, maintenance, or troubleshooting.
• During maintenance, only cut hair, fibers, or string wrapped around the brushroll.
• Allow all filters to air-dry completely before replacing.
• Do not modify or attempt to repair the vacuum or battery yourself.
• Disconnect the battery pack before making adjustments, changing accessories, or storing the appliance.

Battery Pack Safety:

• The battery is the power source; follow all charging instructions.
• Ensure the vacuum is powered off before picking up or carrying.
• Use only specified Shark® chargers (DK30A-263100H-U or YLJX21-T263100 for single-battery packs).
• Keep the battery away from metal objects to prevent shorting.
• Avoid contact with ejected battery liquid.
• Store battery and appliance at appropriate temperatures (avoiding extremes).
• Do not expose the battery to fire or high temperatures.
• Use only designated battery packs (XBATR640US for IP1000 series).
• Turn off and remove the Li-Ion battery before servicing to reduce risk of shock or unintended operation.

Further Information:

Read and save these instructions. Visit qr.sharkclean.com/IP1000seriesmanual or scan the QR code for full instructions and replacement parts.

QR Code Description: A QR code is presented, linking to the full instruction manual and replacement parts.

Copyright © 2024 SharkNinja Operating LLC. MULTIFLEX and SHARK are registered trademarks of SharkNinja Operating LLC. FLOOR DETECT, LIGHT DETECT, and POWERDETECT are trademarks of SharkNinja Operating LLC.