Honeywell Home | Smart Home Comfort & Automation
This section details how to perform system tests on the FocusPRO® 5000 and 6000 Series thermostats.
1. To begin, press and hold the [up arrow] and [down arrow] buttons until the display changes.
2. Press [up arrow][slash][down arrow] to turn system on/off.
System test number: 10
System status number: 0
Done
Next
3. Press NEXT to advance to next test.
4. Press DONE to terminate system test.
5. Proceed to Installer System Tests on page 8.
(Image description: FocusPRO 5000 Series thermostat interface showing display with 'System test number' as '10' and 'System status number' as '0'. Below the display are 'Done' and 'Next' buttons.)
1. To begin, press and hold the [up arrow] and [down arrow] buttons until the display changes.
2. Press [up arrow][slash][down arrow] to turn system on/off.
System test number: 10
System status number: 0
Done
Next
3. Press NEXT to advance to next test.
4. Press DONE to terminate system test.
5. Proceed to Installer System Tests on page 8.
(Image description: FocusPRO 6000 Series thermostat interface showing display with 'System test number' as '10' and 'System status number' as '0'. Below the display are 'Done' and 'Next' buttons.)
Test the system's heating, emergency heat, cooling, and fan. Available tests vary by thermostat and system type.
| System Test Number | Test Type | System Status Number and Description |
|---|---|---|
| 10 | Heating system | 0: Heat and fan off |
| 1: First stage heat on (Fan turns on if Setup Function 1 is set to 1, 5, 9, or 10 OR setup Function 3 is set to 1) | ||
| 2: Second stage heat on | ||
| 3: Third stage heat on | ||
| 20 | Emergency heating system | 0: Heat and fan off |
| 1: Heat and fan on | ||
| 2: Second stage heat (Aux. heat) turns on | ||
| 30 | Cooling system | 0: Compressor and fan off |
| 1: Compressor and fan on | ||
| 2: Second stage compressor on | ||
| 40 | Fan system | 0: Off |
| 1: On |
CAUTION EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.
This section covers the installer setup functions for the FocusPRO® 5000 and 6000 Series thermostats.
1. To begin, press and hold the [up arrow] and FAN buttons until the display changes.
2. Press [up arrow] or [down arrow] to change settings.
Function
Setting
Done
Next
3. Press NEXT to advance to the next function.
4. Press DONE to exit and save settings.
5. Proceed to Installer Setup Functions on page 4.
(Image description: FocusPRO 5000 Series thermostat interface showing display with 'Function' and 'Setting' labels. Below the display are 'Done' and 'Next' buttons.)
1. To begin, press and hold the [up arrow] and FAN buttons until the display changes.
2. Press [up arrow] or [down arrow] to change settings.
Function
Setting
Done
Next
3. Press NEXT to advance to the next function.
4. Press DONE to exit and save settings.
5. Proceed to Installer Setup Functions on page 4.
(Image description: FocusPRO 6000 Series thermostat interface showing display with 'Function' and 'Setting' labels. Below the display are 'Done' and 'Next' buttons.)
Available option and default settings vary by thermostat.
| Setup functions | Setting & Options (factory default in bold) |
|---|---|
| 1. System type | 0: 1 heat/1 cool Conv. 1: 1 heat/1 cool heat pump (no Aux. heat) 2: Heat only (2-wire, 3-wire zone valves [Series 20], and normally open zone valves) 3: Heat only with fan 4: Cool only 5: 2 heat/1 cool heat pump (with Aux. heat) 6: 2 heat/2 cool Conv. 7: 2 heat/1 cool Conv. 8: 1 heat/2 cool Conv. 9: 2 heat/2 cool heat pump (no Aux. heat) 10: 3 heat/2 cool heat pump (with Aux. heat) |
| 2. Changeover valve (O/B terminal) | 0: Controls valve in cooling 1: Controls valve in heating |
| 3. Fan control (heating) | 0: Gas/Oil heat (equipment controls heating fan) 1: Electric furnace (thermostat controls heating fan) |
| 5. First stage heat cycle rate | 5: Gas or oil furnaces of less than 90% efficiency 1: Steam or gravity 3: Hot water systems or furnaces of 90%+ efficiency 9: Electric furnaces [Other options: 1-12] |
| 6. Second stage heat/Aux heat cycle rate | 5: Gas or oil furnaces of less than 90% efficiency 1: Steam or gravity 3: Hot water systems or furnaces of 90%+ efficiency 9: Electric furnaces [Other options: 1-12] |
| 7. Auxiliary heat cycle rate | 5: Gas or oil furnaces of less than 90% efficiency 1: Steam or gravity 3: Hot water systems or furnaces of 90%+ efficiency 9: Electric furnaces [Other options: 1-12] |
| 8. Emergency heat cycle rate | 9: Electric emergency heat 1: Steam or gravity 3: Hot water systems or furnaces of 90%+ efficiency 5: Gas or oil furnaces of less than 90% efficiency [Other options: 1-12] |
| 9. First stage compressor cycle rate | 3: Recommended [Other options: 1-6] |
| 10. Second stage compressor cycle rate | 3: Recommended [Other options: 1-6] |
| 12. Manual/Auto changeover | 0: Manual changeover (Heat/Cool/Off) 1: Auto changeover (Heat/ Cool/Auto/Off) 2: Auto changeover only (Auto) |
| 13. Adaptive Intelligent Recovery™ | 0: Off 1: On |
| 14. Temperature display | 0: Fahrenheit 1: Celsius |
| 15. Compressor protection | 5: 5-minute compressor off time [Other options: 0-4 minutes] |
| 16. Schedule format | 0: 5/2 (weekdays and weekends programmable) 1: 5/1/1 (weekdays, Saturday, and Sunday programmable) |
| 26. Auxiliary heat control | 0: Comfort 1: Economy |
| 27. Heat temperature range stops | 90: Max. heat temperature setting is 90°F (32°C) [Other options: 40-89°F (4.5°C to 32°C)] |
| 28. Cool temperature range stop | 50: Min. cool temperature setting is 50°F (10°C) [Other options: 51-99°F (10.5°C to 37°C)] |
Functions 13 and 16 only available on the 6000 series; function 26 only available on the 5000 series.
File Info : application/pdf, 2 Pages, 197.62KB
DocumentDocument |
Honeywell FocusPRO 5000 & 6000 Series Thermostats: Installer Setup and System Test Guide A comprehensive guide for installers on setting up and testing Honeywell FocusPRO 5000 and 6000 Series thermostats, covering system tests and installer setup functions. |
 |
Honeywell FocusPRO 5000 and 6000 Series Thermostat Installation and System Test Guide Comprehensive guide for installing and testing Honeywell FocusPRO 5000 and 6000 series thermostats, covering configuration options and system test procedures for heating, cooling, and fan functions. |
 |
Honeywell FocusPRO 5000 Series Non-Programmable Digital Thermostat Installation Guide Installation instructions for the Honeywell FocusPRO 5000 series non-programmable digital thermostat, covering wallplate installation, power options, wiring for conventional and heat pump systems, thermostat mounting, installer setup, system tests, and specifications. |
 |
Honeywell FocusPRO TH6220D Programmable Thermostat Installation Guide Comprehensive installation guide for the Honeywell FocusPRO TH6220D Programmable Thermostat, covering product application, system types, power options, wiring, installer setup, system testing, troubleshooting, and specifications. |
 |
Honeywell TH5110D Non-Programmable Thermostat Operating Instructions Comprehensive operating instructions for the Honeywell TH5110D Non-Programmable Thermostat, covering features, setup, operation, battery replacement, troubleshooting, and warranty information. |
 |
Honeywell FocusPRO TH5220D Non-programmable Digital Thermostat Installation Guide Comprehensive installation guide for the Honeywell FocusPRO TH5220D non-programmable digital thermostat. Covers product application, system types, power options, installation tips, wiring diagrams, installer setup, system testing, and troubleshooting. |
 |
Honeywell FocusPRO TH5220D Non-Programmable Digital Thermostat Installation Guide Installation guide for the Honeywell FocusPRO TH5220D non-programmable digital thermostat, covering product application, system types, power options, wiring, setup, testing, and troubleshooting. |
 |
Honeywell FocusPRO TH5000 Series Thermostat Installation Guide Comprehensive installation guide for the Honeywell FocusPRO TH5000 Series non-programmable digital thermostats, covering models TH5110D, TH5220D, and TH5320U. Includes wiring diagrams, setup procedures, and specifications. |