Item Number: 6910634

WARNING (To reduce the risk of fire, electric shock, or personal injury):

Installation by a licensed electrician is suggested.
Read these instructions carefully and save them for future reference.
NEVER attempt any work without shutting off the electricity until the work is done.
Go to the main fuse, or circuit breaker, box in your home and place the main power switch in the “OFF” position.
Place the wall switch in the “OFF” position.
The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Ensure the ceiling or wall can support the weight of the lamp before installation.
The voltage used must be 120V. The maximum wattage per bulb is Type A, Max 60W.
Keep the lamp away from acidic and alkaline substances to prevent damage to the lamp's surface.
When replacing bulbs, turn off or unplug the lamp and wait until it is cool, as bulbs get hot quickly.
The safety instructions in this manual are not exhaustive. Common sense, caution, and care must be used with any electrical products.

Image for Finished Product:

A diagram showing a three-light pendant fixture with glass shades.

Tools Required (Not Included):

Ladder
Philips Head or Flat Blade Screwdriver
Electrical Tape
Pliers
Wire Cutter/Stripper

A visual representation of the tools required for installation.

Parts Type & Qty Including:

(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Strain relief (6)
(G) Nex nut (1)
(H) Cap nut (1)
(I) Cord (3)
(J) Socket assembly (3)
(K) Screw (9)
(L) Lampshade (3)

Accessories & Qty Enclosed:

(A) Plastic Wire Connector (3)
(B) Mounting screw (2)
(M) Allen wrench (1)
(K) Screw (1) (spare part)

Assembly & Installation Instructions:

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
Turn off power. Before starting installation, NEVER attempt any work without shutting off the electricity until the work is done. Go to the main fuse or circuit breaker box and turn the main power switch to “OFF”. Turn the wall switch to “OFF”.
Unscrew hex nut (G) and cap nut (H) from single bar (C).
Adjust the length of cords (I) to achieve the desired height of the mounted fixture. Use Allen wrench (M) to unscrew screws in strain reliefs (F). Carefully pull and push cords (I) through canopy (E) and strain reliefs (F) to lengthen or shorten the cords. Once the desired height is achieved, carefully tighten the screws until snug.
Secure single bar (C) to the outlet box with mounting screws (B). NOTE: The side of single bar (C) marked “GND” must face out.
Make wire connections. Connect wires as shown in the diagram. Refer to the following charts. NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart:

Diagram showing how to connect ground wires from the outlet box and fixture to the green ground screw.

Connect wires according to the below chart:

Connect Black or Red Supply Wire to:	Connect White Supply Wire to:
Black (*Parallel cord (round & smooth))	White (*Parallel cord (square & ridged))
Clear, Brown, Gold or Black without tracer. Insulated wire (other than green) with copper conductor.	Clear, Brown, Gold or Black with tracer. Insulated wire (other than green) with silver conductor.

*Note: When parallel wires (SPT I & SPT II) are used, the neutral wire is square shaped or ridged and the other wire will be round in shape or smooth.

Neutral Wire

Twist wires together with plastic wire connector until tightly joined.

Wrap each connector with approved electrical tape for a more secure connection.

Carefully tuck all wires into the outlet box.

Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening hex nut (G) and cap nut (H) onto the pre-assembled threaded nipple on single bar (C). NOTE: The canopy (E) should be snug against the ceiling and cap nut (H). If not, adjust the threaded length of the pre-assembled threaded nipple on single bar (C) by first unscrewing the pre-assembled hex nut, then screwing the pre-assembled threaded nipple in or out of single bar (C). When the secure length is achieved, tighten the pre-assembled hex nut and back to step 7.

Diagram showing the canopy being secured to the ceiling.

1) Remove screws (K) from socket assemblies (J).

2) Align holes of lampshades (L) with holes of socket assemblies (J) and then secure them with screws (K) as shown in the illustration.

3) Install bulbs (Not included). Please do not exceed the maximum wattage recommended on the socket.

Diagram illustrating the attachment of lampshades to socket assemblies and bulb installation.

Check everything is installed properly, then you can turn on the light. Enjoy!

Ordering Parts

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustration when ordering parts.

Cleaning

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Models: 6910634 Single Bar Pendant Light Fixture, 6910634, Single Bar Pendant Light Fixture, Bar Pendant Light Fixture, Pendant Light Fixture, Light Fixture

Google Docs
Google Drive
Download [pdf]
Download Optimized

File Info : application/pdf, 4 Pages, 609.02KB

72218505

Related Documents

	Modern Luxury Round Crystal Chandelier Installation Guide This guide provides step-by-step instructions for installing the Modern Luxury Round Crystal Chandelier, featuring a contemporary design suitable for hallways and hotel entryways.
	Pendant Light Installation Guide and Instructions Comprehensive guide for installing a pendant light fixture, including safety precautions, step-by-step instructions, and parts list. Suitable for professional electricians.
	Assembly and Installation Instructions for Pendant Light Fixture Detailed instructions for the safe and proper assembly and installation of a pendant light fixture, including safety precautions and step-by-step guidance.
	Installation Guide for 5128688 Chandelier Step-by-step instructions for installing the 5128688 chandelier, including safety warnings, required tools, parts list, assembly, wiring, and cleaning.
	White Track Light - Actual Photo Actual photo of a white track light, showcasing its side view. This product is a lighting fixture designed for track lighting systems.
	High-Power LED Floodlight for Outdoor Illumination Detailed information on a robust, high-power LED floodlight designed for efficient and reliable outdoor lighting applications. Features include adjustable mounting, durable construction, and advanced LED technology for superior brightness and longevity.
	Elegant Outdoor Wall Sconce - Black Lantern Style A detailed description of an outdoor wall-mounted lantern, featuring a black finish and a classic lantern design with frosted glass panels, suitable for enhancing exterior lighting.
	15781G Pendant Light Dimensions and Specifications Technical drawing and specifications for the 15781G pendant light, detailing dimensions, electrical information, and color temperature options.