GE Pre-Lit Christmas Trees with Easy Light Technology
Assembly Instructions
Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas tree. For more information or assistance, visit www.geholidaylighting.com or call toll-free at 1-877-398-7337. Check the website for the latest service hours and assembly instruction videos.
Tree Assembly Diagram (7.5 FT / 2.28 M)
Note: No tools required.
a. This tree is provided with an extension cord for a tree topper, which can be attached to the top section along the pole.
b. As an option, the tree adapter can be plugged into the back of the tree top extension cord as an add-on. This feature allows you to utilize only one outlet.
Step 1: Unpack and Inspect
Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree. The carton should include sections labeled "A", "B" and "Top", as well as a Tree Stand.
Step 2: Set Up Tree Stand
The tree stand should be open and set at a 90° angle. Tighten the thumbscrew.
[Diagram showing tree stand opening to 90° with thumbscrew]
Step 3: Insert Section A
Insert Section labeled A into the tree stand, tighten the thumbscrew. Then insert the plug into an electrical wall outlet.
[Diagram showing Section A inserted into stand and plugged into wall outlet]
Step 4: Shape Branches
Untie the RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer layer of branches.
Fig. A: Start at the inner and stagger the tips. Move each tip up to 40°.
Fig. B: Make tips 2 & 3 horizontal, tip 4 vertical, and tips 5 & 6 up to 45°.
[Diagram illustrating branch shaping angles: 40°, 90°, 45°]
Step 5: Assemble Section B
To assemble the section labeled "B", properly align and insert section "B" into the top of section "A". Adjust branch tips, as needed, for a fuller look.
[Diagram showing alignment mark for connecting sections B and A]
Step 6: Shape Branches (Repeat)
Repeat "Step 4" for shaping.
Step 7: Assemble Top Section
To assemble the tree top, properly align and insert the "TOP" section into the top of section "B". Adjust branch tips, as needed, for a fuller look.
[Diagram showing alignment mark for connecting TOP section to B]
Step 8: Select Lighting Function
Gently press on the foot pedal to select the desired lighting function.
Function List:
- 1. Steady White
- 2. Steady Multi
- 3. SLO-GLO
- 4. White SLO-GLO Flashing
- 5. Multi SLO-GLO
- 6. White Flashing
- 7. Multi Flashing
- 8. Change/Twinkle
- 9. Off
[Diagram of foot pedal]
Schematic Diagram
Tree Sections: 7.5 ft tree has 3 sections (A, B, Top). Tree Stand is metal. Approx. Assembly Time: 5-10 minutes.
[Schematic diagram showing tree sections A, B, Top, Tree Stand, AC Connector, Easy Light Technology, Color Change Foot Pedal, Tree Extension Cord]
Troubleshooting Tips
If the tree does not illuminate, try stepping on the Color Change Foot Pedal and make certain the wall switch is turned on. If one section of your tree does not illuminate, check that section for loose or missing bulbs, ensure all factory connections are properly made, or that you have correctly made all electrical connections between each tree section (i.e., tree plug to extension cord outlet).
Disclaimer
DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. Doing this may result in damage to your Christmas tree or cause personal injury. Doing this will void the limited warranty of this product.
Disconnect the decorative item from the power source before performing any maintenance or cleaning.
For indoor use only. 120V.
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
GE is a trademark of General Electric Company and is under license by Nicolas Holiday Ltd.
Tree Storage
- Remove the tree's main extension cord plug from the wall outlet.
- Starting at the top, disconnect the "TOP" from section "B" and then disconnect section "B" from section "A". {Fig. 1}
- Note: Gently fold the tips in branches and fold the branches up toward the center. {Fig. 2} Care should be taken to avoid damage to the lights.
- Remove section "A" from the tree stand and close the tree stand to place into the carton.
- Refer to the drawing on how to repack your tree. {Fig. 3}
[Diagram showing tree sections being disconnected and folded]
IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree life and to better keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to or crushing the carton and tree inside.
