GE Pre-Lit Christmas Trees with Easy Light Technology®

Color Choice® LED Technology Assembly Instructions

Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas tree. For assistance, visit www.geholidaylighting.com or call toll-free at 1-877-398-7337. Check the website for the latest service hours and assembly instruction videos.

Tree Assembly Diagram

Tree Height: 9 FT

Tree Sections: 4

Tree Stand: Metal

Approx. Assembly Time: 5-10 minutes

Components:

Tree Sections (labeled A, B, C, Top)
Tree Stand
AC Connector for Tree Top
Color Change Foot Pedal
Tree Extension Cord

Assembly Steps:

Carefully unpack the carton. Remove bubble wrap and inspect the tree sections. Ensure all sections (A, B, C, Top) and the Tree Stand are present.
Diagram shows unpacking and inspecting tree sections.
Open the tree stand and set it at a 90° angle. Tighten the thumbscrew.
Diagram shows opening the tree stand to a 90° angle with a thumbscrew.
Insert the section labeled A into the tree stand and tighten the thumbscrew. Plug the section into an electrical wall outlet.
Diagram shows inserting section A into the stand and plugging it in.
Untie the RED twist-tie to release branch panels. Gently pull the outer layer of branches to allow them to fall into place. Shape the tips:
- Fig. A: Start from the inner branches and stagger tips upwards to 40°.
- Fig. B: Position tips 2 & 3 horizontally, tip 4 vertically, and tips 5 & 6 at a 45° angle.
Diagrams illustrate branch shaping angles (40°, 90°, 45°).
Assemble the next section (B or C) by aligning and inserting it into the top of the previous section (A or B). Adjust branch tips for a fuller look. Ensure alignment marks are matched.
Diagram shows connecting two tree sections, highlighting alignment marks.
Repeat Step 4 for shaping the branches of the newly added section.
Assemble the tree top by aligning and inserting the "TOP" section into the top of section C. Adjust branch tips as needed. Ensure alignment marks are matched.
Diagram shows connecting the top section, highlighting alignment marks.
Gently press the foot pedal to select the desired lighting function. Refer to the function list below.
Diagram shows a foot pedal with the number 8.

Function List:

1. Steady White
2. Steady Multi
3. SLO-GLO
4. White SLO-GLO Flashing
5. Multi SLO-GLO
6. White Flashing
7. Multi Flashing
8. Change/Twinkle
9. Off

Troubleshooting Tips

If the tree does not illuminate: Step on the Color Change Foot Pedal and ensure the wall switch is on. If a section is not illuminating: Check for loose or missing bulbs, ensure all factory connections are properly made, and verify electrical connections between tree sections.

DISCLAIMER: DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION POWERED BY A LIGHT BULB SOCKET. Doing so may damage the tree or cause personal injury and will void the limited warranty.

Disconnect the decorative item from the power source before performing maintenance or cleaning.

For indoor use only. 120V. This is not a toy; for decorative use only.

Tree Storage

Unplug the tree's main extension cord from the wall outlet.
Starting from the top, disconnect the "TOP" section from section "C", then disconnect section "B" (or "C") from section "A" (or "B").
Gently fold the branch tips inward and fold the branches up toward the center. Take care to avoid damaging the lights.
Remove section "A" from the tree stand and close the stand for storage in the carton.
Refer to the diagram for repacking instructions.

Diagrams show disconnecting sections and folding branches.

IMPORTANT:

Store the carton neatly in a cool, dry location protected from sunlight to prolong the tree's life and keep the light sets in working order. Do not place heavy loads on the carton to avoid damage or crushing.

Spare Parts Included:

Item	Quantity
3-amp fuse	2 pcs
(Unspecified small parts)	12 pcs

GE is a trademark of General Electric Company and is under license by Nicolas Holiday Ltd.

	GE Pre-Lit Christmas Trees with Easy Light Technology Assembly Instructions Comprehensive assembly instructions for GE Pre-Lit Christmas Trees featuring Easy Light Technology and Color Choice LED Technology. Includes diagrams, troubleshooting tips, and storage guidance.
	GE Pre-Lit Christmas Trees with Easy Shape Technology Assembly Instructions Assembly instructions for GE Pre-Lit Christmas Trees with Easy Shape Technology and Easy Light Technology. Includes diagrams and troubleshooting tips for indoor use.
	GE Pre-Lit Christmas Tree Assembly and Usage Guide Detailed assembly, operation, and storage instructions for GE Pre-Lit Christmas Trees featuring Easy Light Technology and Color Choice LED technology. Includes troubleshooting tips and product information from Nicolas Holiday Ltd.
	GE Pre-Lit Christmas Trees with Easy Light Technology Assembly Instructions Assembly instructions for GE Pre-Lit Christmas Trees with Easy Light Technology, featuring Color Choice LED Technology. Includes steps for tree assembly, shaping branches, selecting lighting functions, troubleshooting, and storage.
	GE Pre-Lit Christmas Trees with Easy Light Technology Assembly Instructions Assembly instructions for GE Pre-Lit Christmas Trees with Easy Light Technology, featuring Color Choice LED Technology. Includes step-by-step guidance for setup, shaping, and storage, along with troubleshooting tips.
	GE Pre-Lit Christmas Trees Color Choice LED Technology Assembly Instructions Assembly instructions for GE Pre-Lit Christmas Trees with Color Choice LED Technology. Includes diagrams and troubleshooting tips for setting up and storing the tree.
	GE Pre-Lit Christmas Trees with Easy Shape Technology Assembly Instructions Assembly instructions for GE Pre-Lit Christmas Trees featuring Easy Shape Technology and Easy Light Technology with warm white multifunction LEDs. Includes diagrams and troubleshooting tips.
	GE Winterberry Branch Tree Assembly Instructions Assembly instructions for the GE Winterberry Branch Tree with Color Choice LED Technology. Includes setup, troubleshooting, and care information.