OWNER'S MANUAL

LINEAR ELECTRIC FIREPLACE WITH HEATER

MODEL# EFW-TJ34A

ATTACH YOUR RECEIPT HERE

Purchase Date: _________________________ Serial Number (located on back of unit): _________________________

Questions, problems, missing parts? Contact technical support department at 657-341-0362, 9:00 a.m. - 5 p.m., CST, Monday - Friday or visit us online at www.lifesmartcomfort.com

Please have your model and serial number ready

LIFE SMART

WARNING Read and understand this entire owner's manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.

CAUTION Keep this owner's manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.

NO VENTING REQUIRED

110V AC; 60 Hz; 1500 Watts

IMPORTANT SAFETY INSTRUCTIONS!

WARNING

Read all instructions before using this heater!
This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (36") from the front of the heater, and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used.
DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or call a certified technician for examination and or/repair.
DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over.
Connect to properly grounded outlets ONLY.
DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock, fire, or damage the heater.
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp, or come in contact with water.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
NEVER hang this unit on a wall directly below an electrical outlet.
NEVER permanently install in a recessed area of the wall. This may result in blocked air flow, overheating, or fire.
NEVER use a wall mount bracket from another manufacturer.

NOTICE Pictures within this manual are for reference only. Please refer to the actual product for appearance.

WARNING

For residential use only! NOT for commercial use! Any commercial or public use of this heater voids all warranties, and could cause injury.
This product is not intended to be a primary heat source. It is for supplemental heat only.
INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
NEVER modify this heater. Doing so could result in personal injury or property damage. Modification of this fireplace completely voids all warranties.
ALWAYS turn this heater off before unplugging it from the outlet.
ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the product.
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
ALWAYS store this heater in a dry location. NEVER use the product if it has become wet.
Place the heater near a wall outlet so an extension cord is not needed.
ONLY use this heater on a minimum 110V AC 15-Amp grounded circuit. NEVER overload the circuit. If this heater trips the circuit breaker, or blows the fuse, unplug it and all other appliances on the same circuit before the next use.
NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use!
Make sure the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
During use check frequently to see if the plug outlet or faceplate is HOT!
If the outlet or faceplate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.

The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one round pin (ground). If a 3-slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right).

[NOTE: Adapter NOT INCLUDED.]

SAVE THESE INSTRUCTIONS!

Diagram showing a 3-prong plug with an adapter connected to a 2-prong outlet, with a grounding wire attached to the outlet box screw.

PREPARATION

! This product includes GLASS! ALWAYS use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, and dry surface.
Make sure all parts are dry, and the power cord and plug are not damaged. See IMPORTANT SAFETY INFORMATION on pages 2 and 3.
Compare the contents with the parts list to make sure nothing is missing.
Dispose of all packaging materials properly. Please recycle whenever possible.

TOOLS NEEDED (NOT INCLUDED)

Diagrams of tools: Phillips Screwdriver, Stud Finder, Level, Tape Measure, Electric Drill, 1/4" Wood Drill Bit, Hammer.

PARTS AND HARDWARE

Diagram showing: Fireplace (A), 3-Wood Screws (B), 3-Drywall Anchors (C), 2-M4x8 Metal Screws (D), 4-M6x14 Bolts (H), 3-Metal Washers (J), and a Remote Control.

INSTALLATION AND ASSEMBLY

! ALWAYS make sure the unit is unplugged before beginning assembly! NEVER move or clean the heater while it is plugged in.

STEP 1: Find a safe location.

Minimum clearance on each side: 20".
Minimum clearance below: 20". (Wall mount only).
Minimum clearance above: 39.5".
Minimum clearance from the front: 36".
Choose a location near an outlet so an extension cord is not required.
DO NOT position the unit directly below a power outlet.

Diagram showing minimum clearance requirements for wall mounting.

NOTICE ! The Drywall Anchors(C) included with this fireplace are for use ONLY with a wood framed wall covered in drywall (sheet rock). For concrete walls, cinder blocks, or other wall types, consult a professional for the best attachment methods.

ALWAYS unplug this fireplace heater before assembly, cleaning, or relocating. Failure to do so could result in electric shock, fire, or personal injury.

STEP 2: Locate the wall studs using an electronic stud finder.

If three studs are available, use stud as center and drill 2 holes on either side of stud (each hole should be 16" apart from another).
STEP 2a: If two studs are available, drill 1 hole in each using 1/4" drill bit. Drill third and final hole in between the two studs.
STEP 2b: If only 1 stud is available, use stud as center and drill 2 holes on either side of stud (each hole should be 13.4" apart from another).

STEP 3: With a hammer, tap the Drywall Anchors(C) carefully into the hole(s) until they are flush with the drywall surface. Use care to avoid damaging the drywall with the hammer.

Diagrams illustrating drilling holes for drywall anchors in different stud configurations (two studs, one stud) and inserting drywall anchors.

! AVOID INJURY and DAMAGE! Wood Screws(B) should be screwed directly into wall studs when possible.

STEP 4: Align the holes in the Wall Bracket(E) with the pilot holes and Drywall Anchors(C). Thread three Wood Screws(B) and Metal Washers (J) through the holes in the wall bracket and directly into the wall studs and Drywall Anchors(C). Make sure the Wall Bracket(E) is level. Tighten all screws securely with a screwdriver.

Diagrams showing how to attach the wall bracket to the wall using wood screws and drywall anchors for both two-stud and one-stud configurations.

NOTE: WE RECOMMEND THAT TWO CAPABLE ADULTS PERFORM THIS PROCEDURE.

STEP 5: With the help of a capable adult, lift the Fireplace(A) and align the two hooks on the back of the fireplace with the slots on the Wall Bracket(E). Carefully set the hooks into the slots.

STEP 5a: Secure the fireplace to the Wall Bracket(E) with two M4x8 Metal Screws(D), one on each side. Thread the Metal Screws (D) through the fireplace and into the Wall Bracket(E) side tabs. Tighten both screws with a screwdriver.

Diagrams showing the back of the fireplace with hooks, and a side view of the fireplace being secured to the wall bracket with metal screws.

CONTROL PANEL FUNCTIONS

NOTICE When the heat function is used for the first time, a slight odor may be present. This is normal and should not occur again unless the heater is not used for an extended period of time.

CONTROLS	FUNCTION
Power	Press once. Flame effect turns on High and indicator light turns on. Press again. Power and all functions turn off.
Flame +/-	Press Flame (+/-) Button to desired flame brightness. 3 options. ONLY works when flame button is ON.
Flame Speed	Press Flame Speed Button to desired flame speed. 5 options.
Timer +/-	Press Timer (+/-) once to increase timer setting by 1/2 hour increments. Maximum timer setting is 7 1/2 hours. Indicator light will illuminate. Press Timer (+/-) button again to turn off timer.
Heater	Press Heater Button once, 750W (LOW HEAT) heater turns on and the fan starts to blow warm air. Press Heater Button again, turns on 1,500W (HIGH HEAT) heater turns on and blows hot air. Press Heater Button again and the heater turns OFF. The fan will continue to blow to allow heater to cool down, and then turns off. NOTE: The Heat Enabling Switch (on the back of the unit) must be ON for the Heater function to operate.
Thermostat Control Knob	Heater must be ON either LOW or HIGH heat for the thermostat function to operate. The heat output is controlled by the Thermostat Control Knob. Set the Thermostat Control Knob to the maximum position initially. When the room reaches the desired temperature, reduce the setting by slowly turning the thermostat knob, counterclockwise until the heater will click and turn off. The heater will then maintain the room temperature at the desired level. NOTE: The Heat Enabling Switch (on the back of the unit) must be ON for the Heater function to operate.
Main Power ON/OFF	Press ON. Power turns ON. All functions are enabled. Press OFF. Power, flame effect, and all functions turn off.

REMOTE CONTROL FUNCTIONS

NOTICE MAIN POWER ON THE FIREPLACE CONTROL PANEL MUST BE IN THE ON POSITION TO USE REMOTE CONTROL.

REMOTE CONTROL BUTTONS	FUNCTION
POWER	Press once to turn Power ON. Press again to turn Power OFF.
HEATER	Press Heater Button once, 750W (LOW HEAT) heater turns on and the fan starts to blow warm air. Press Heater Button again turns on 1,500W (HIGH HEAT) heater turns on and blows hot air. Press Heater Button again and the heater turns OFF. The fan will continue to blow to allow heater to cool down, and then turns off. NOTE: The Heat Enabling Switch (on the back of the unit) must be ON for the Heater function to operate.
FLAME +/-	Press Flame (+/-) Button to desired flame brightness. 3 options. ONLY works when Flame button is ON.
TIMER +/-	Press Timer (+/-) once to increase timer setting by 1/2 hour increments. Maximum timer setting is 7 1/2 hours. Indicator light will illuminate. Press Timer (+/-) button again to turn off timer.
FLAME SPEED	Press Flame Speed Button to desired flame speed. 5 options.

NOTICE To improve operation, aim the remote control at the front of the fireplace. DO NOT press the buttons too quickly. Give the unit time to respond to each command.

REMOTE CONTROL BATTERY INFORMATION

This remote control uses one CR2025 battery (included).
Instructions for battery installation are on the Remote Control Battery compartment.

Diagram showing how to open the remote control battery compartment.

! NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

CARE AND MAINTENANCE

! ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

! NEVER immerse in water or spray with water or other liquids (ex: cleaning solutions). Doing so could result in electric shock, fire, or personal injury.

CLEANING

Metal:

Dust using a brush or lint-free cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these will damage the metal.

Glass:

Spray glass cleaner onto soft cloth (NOT directly on to glass). Dry thoroughly with a paper towel or lint-free cloth.
NEVER use abrasive cleansers or any cleaner that could scratch the surface.

Plastic:

Wipe with a slightly damp cloth and a mild solution of dish soap and warm water. Dry off surface.

Vents:

Use a vacuum or duster to remove dust and dirt from the heater and vent areas as needed.

! Risk of electric shock! DO NOT OPEN any panels! No user-serviceable parts inside!

Electrical and Moving Parts:

The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the consumer.

Storage:

Store heater in a clean dry place when not in use.

ONE-YEAR LIMITED WARRANTY

The manufacturer warrants this heater against defects in materials and workmanship on functional parts, for a period of 1 year from the original date of purchase. Your sales receipt showing the date of purchase of the product is your proof of purchase. Keep it in a safe place for future reference. This warranty is subject to personal use only, commercial or rental applications will not be covered.

This product is made with the highest quality materials and is warranted to be free from defects in materials and workmanship at the time of purchase. This limited warranty applies to products manufactured or distributed by the manufacturer, are delivered in the continental United States or Canada and extends to the original purchaser, or gift recipient. This warranty becomes valid at the time of purchase and terminates either by the specified time frame listed above and/or owner transfer. Any refunds or monetary compensations must be claimed through the place of purchase (retailer), and not through the manufacturer. Any extended warranties (warranties that cover above and beyond this manufacturer warranty) that are sold through a retailer or third party, are not directly correlated with this products' limited warranty, and may be redirected to said retailer or third party for coverage.

This warranty extends through the manufacturer of the product, and covers functional parts only. Cosmetics are not covered, unless unequivocally determined it is a workmanship defect. Shipping damage should be addressed with the shipping company, retailer, or place of purchase, not the manufacturer unless the manufacturer was the direct shipper.

The manufacturer's sole obligation under this warranty shall be limited to furnishing the original purchaser replacement parts for units deemed repairable by the supplier's warranty department. The purchaser is responsible for insuring any parts shipped or returned, if desired. The purchaser is responsible to prepay any shipping charges (both ways) including, but not limited to taxes and duties. All exchanged parts and products replaced under this warranty will become the property of manufacturer. The manufacturer reserves the right to change manufacturers of replacement parts or products for use, in order to cover any existing warranty.

The purchaser may be asked to provide the supplier with proof of purchase documents (including the date of purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase documents will be just cause to VOID this limited warranty. Products, in which the serial number has been defaced or removed are not eligible for warranty coverage.

This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or repairs, alteration by non-manufacturer authorized personnel, inappropriate installations, or any case beyond the control of the manufacturer. Examples of warranty invalidation may also include, but are not limited to:

Use of lacquer or paints in (and around) the heaters
Heater placed on non-approved surfaces
Electrical requirement deficiencies (15-20 amp dedicated outlet)
Use on extension cords/timers/surge protectors/GFCI
Outdoor applications
Normal wear/tear/weathering
Pet/consumer accidents
Purchases from dealers unauthorized by the manufacturer (Authorization in writing)

The manufacturer shall not be liable for any loss due to use (or misuse) of the heater or other incidental or consequential costs, expense or damages without irrefutable foundations. Under no circumstances shall the manufacturer or any of its representatives be held liable for injury to any person or damage to any property, however arising. Any implied warranty shall have duration equal of the applicable warranty stated above. Specifications are subject to change without notice or obligation.

This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state to state.