Waterdrop Alkaline Faucet Filtration System

About the System

Thank you for choosing the Waterdrop Alkaline Faucet Filtration System. This filtration system utilizes advanced alkaline mineralization technology, featuring a high-precision composite filter cartridge made of activated carbon block and PP cotton. It provides you with clean and healthy water by improving taste and effectively removing harmful substances such as chlorine, discoloration, odors, sediment, rust, suspended particles, and colloids. At the same time, it adds beneficial minerals to the water, increases the pH level, and perfectly meets your needs for clean and healthy water.

System Specifications

To achieve optimal performance, it is recommended to use the system within the system specifications.

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Parts List

Diagram showing various components labeled A through J, and accessories K-1 and K-2.

• (A) Alkaline Activated Carbon Block Filter: A cylindrical filter cartridge.
• (B) Mechanical Life Reminder Device: A small dial or indicator.
• (C) Filter Top Cover: The cap for the filter housing.
• (D) Filter Base: The main housing for the filter.
• (E) Mounting Nut: A nut used to secure the system to the faucet.
• (F) Silicone Washer: A sealing washer.
• (G) Steel Mesh: A mesh component, likely for pre-filtering.
• (H) Mounting Base: The part that attaches to the faucet.
• (I) Display Area: An area on the unit, possibly for the life reminder.
• (J) PUSH Button: The button to switch between filtered and unfiltered water.

Accessories:

• (K-1) 6x Adapter: A set of six threaded adapters including M18.5 (A5), 13/16" (A4), M21.5 (A6), 15/16" (A3), M18.5 (B4), 55/64" (B3).
• (K-2) 1x Teflon Tape: A roll of Teflon tape for sealing threads.

Note: When the display area is set to "PURE," the faucet provides filtered purified water; when it is set to "TAP," the faucet supplies unfiltered tap water.

Installation Instructions

Step 1: Prepare Faucet

Visuals show removing an existing faucet aerator and then presenting a selection of threaded adapters for both male and female faucet threads. For internal threaded faucets, choose from A5, A4, A6 or A3. For external threaded faucets, choose B4 or B3.

Step 2: Attach Mounting Nut

Illustrations depict unscrewing a mounting nut (E) from a mounting base (H) by turning counter-clockwise, and then placing the nut (E) onto the faucet.

Step 3: Apply Teflon Tape

A diagram shows Teflon tape (K-2) being wrapped around the faucet threads at the connection point. You can hand-tighten the adapter and do not over-tighten it.

NOTE: The silicone washers have been installed into the adapters, and be careful not to omit the washer during the installation. Otherwise, this may cause water leakage.

Step 4: Secure Mounting Base

An illustration demonstrates screwing the mounting base (H) clockwise onto the mounting nut (E) attached to the faucet firmly.

Step 5: Install Filter

Diagrams show unscrewing the filter top cover (C) from the filter base (D), taking out the filter from the package and removing the protective film. Insert the filter into the Filter Base (D). Twist the Filter Top Cover (C) back to Filter Base (D) securely.

NOTE: Please insert the filter firmly until it sits.

Step 6: Align Filter Base

An illustration shows aligning a slot on the filter base (D) with a corresponding slot on the mounting base (H).

Step 7: Insert and Rotate Filter Base

A diagram illustrates inserting the filter base (D) into the mounting base (H) and rotating it 90 degrees upward to lock it in place.

How to Use

After installation, open faucet. Press the "PUSH" button to "pure" position, and the filtered water will run through. Press the "PUSH" button to "tap" position, and unfiltered water will run through.

Two diagrams illustrate the faucet operation: 'Tap Water' shows the PUSH button in the 'tap' position, allowing unfiltered water flow. 'Pure Water' shows the PUSH button in the 'pure' position, allowing filtered water flow.

NOTE:

1. Before first use, run tap water for 1 minute in "pure" position. Do not run hot water above 100°F/38°C through the filter. During flush, it is normal to see cloudy water and hear the sound of water pushing air out of the filter.
2. Check for leaks. If there is any leak, please refer to FAQ or contact customer service staff.
3. Filter Replacement: For optimum performance, it is highly recommended you use genuine Waterdrop faucet replacement water filter. And it is also advisable to change your filter every 3 months or 320 gallons to keep water fresh, whichever comes first. This will vary based on water usage and water quality.
4. The faucet head comes with Mechanical Life Reminder Device that you can twist to align the scale with the month of use, making it convenient to keep track of when you started using it so that you can replace the filter on time.

Filter Replacement

1. Illustration: Twisting the filter base (D) from the mounting base (H).
2. Illustration: Twisting off the filter top cover (C) and removing the old filter.
3. Illustration: Removing protective film from a new filter and inserting it into the filter base (D).
4. Illustration: Twisting the filter top cover (C) back onto the filter base (D).
5. Illustration: Aligning the slot of the filter base (D).
6. Illustration: Inserting the filter base (D) into the mounting base (H) with the slot of Mounting Base (H) and rotating 90° upward.

Warnings

1. Do not use with water temperatures exceeding 100°F (38°C).
2. Flush the system for 1 minute before use if it has been unused for an extended period.
3. Before each use, run water through the filter for 5 to 10 seconds to activate it.
4. The filter system must be protected from freezing temperatures, frost, snow, sleet, and ice. Exposure to these elements may cause cracks or product failure.
5. Do not touch the filtered water outlet to prevent bacterial contamination.
6. Do not use a steel wire brush or corrosive liquids to clean the product.
7. Replace the filter every 3 months or after filtering 320 gallons to maintain optimal performance.

Frequently Asked Questions

Limited Warranty

The Waterdrop Alkaline Filter Faucet Filtration System (Model No.: WD-FC-02-TL) offers a 1-year warranty, which covers defects in materials and workmanship from the original date of purchase.

If the product proves to be defective within 1 year from the date of purchase, please call the technical support hotline. During the warranty period, any part deemed defective will be replaced or repaired, provided the product has not been subjected to tampering, alteration, or improper use after delivery, and has not been repaired by the manufacturer. The product is not warranted against misuse, use in abnormal operation temperature conditions, conditions outside listed operating parameters, use in commercial operations, or any other manner outside the "System Specifications" set forth in the user manual.

The obligation does not include the cost of transportation. Qingdao Ecopure Filter Co., Ltd. is not responsible for damage in transit, and claims for such damage should be presented to the carrier by the customer.

NOTE: It does NOT apply to any filters, which have a life expectancy that varies based on incoming water quality.

Contact Information:

Qingdao Ecopure Filter Co., Ltd.
Tel: 1-888-352-3558 (U.S.)
E-mail: CT@waterdropfilter.com
Add.: No.13, Yishengbai Road, Jimo, Qingdao, China

Made in China

24/7 365 Service