Honeywell Home FocusPRO P200 Series Thermostat

Thermostat Controls

Time: Displays the current time.

Mode: Allows selection of system modes: Heat, Off, Cool, Auto, EM Heat (emergency heat).

Menu: Press to display options and start program scheduling.

Fan: Controls fan operation: Auto, On, Circulate.

Actual indoor temperature: Displays the current indoor temperature.

System status: Indicates system operation: Cool On, Heat On, Aux Heat On.

Temperature/Navigation: Increase or decrease temperature setpoint and navigate menus.

Schedule information: Shows if the thermostat is following a time-based schedule.

Hold: Allows holding the current temperature setting.

Scan for the full User Manual: You can search online for Resideo 33-00691EFS for the Owner's Manual or scan the QR code.

System Operation Settings

System Modes:

1. Press the MODE button to cycle through available System modes (Heat, Off, Cool).
2. Leave the desired mode displayed to activate it.

Fan Operation Settings:

1. Press/release the FAN button to cycle through available Fan modes.
2. Stop pressing the button when the desired Fan mode is displayed.

Fan Modes:

• Auto: Fan runs only when the heating or cooling system is on.
• On: Fan is always on.
• Circulate: Fan runs approximately 33% of the time to circulate air.

Set the Time and Date

Time:

1. Press Menu on the thermostat.
2. Press or to go to TIME, then press Select.
3. Press or to choose 12 or 24-hour clock format, then press Next.
4. Press or to adjust the hour, then press Next.
5. Press or to adjust the minute, then press SAVE & EXIT.

Date:

1. Press Menu on the thermostat.
2. Press or to go to DATE, then press Select.
3. Press or to choose YEAR, then press Next.
4. Press or to adjust the MONTH, then press Next.
5. Press or to choose DATE, then press SAVE & EXIT.

Alerts and Reminders

When an alert is active, the [alert icon] icon appears in the lower part of the display along with the alert number.

When the filter reminder is active, the [filter icon] icon appears along with the number 181.

To Adjust Program Schedules

1. Press Menu on your thermostat. Press or until SCHED is displayed. Press Select.
2. A square appears around ON or OFF. If you want to use a schedule, press or to select ON. Press Next to edit the schedule or press EXIT to exit the menu.
3. If editing the schedule, press Next to edit the day(s) flashing in the display.
4. The word Wake should be flashing. Press NEXT. Press or to turn this schedule period on or off. Press NEXT.
5. If the schedule period was set to ON, the time will be flashing. Press or to adjust the time for this period. Press NEXT.
6. The Heat setpoint will be flashing. Press or to adjust the Heat setpoint for this period. Press NEXT.
7. The Cool setpoint will be flashing. Press or to adjust the Cool setpoint for this period. Press NEXT.
8. The display will show the next schedule period flashing. Repeat steps 4-7 for the other schedule periods and days.
9. Press the SAVE & EXIT button.

Troubleshooting

Display is blank:

• Check circuit breaker and reset if necessary.
• Ensure power switch at heating and cooling system is on.
• Make sure furnace door is closed securely.

"Waiting for Equipment" appears on the screen:

• Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely.

Temperature settings do not change:

• If display says "unlock", thermostat owner has set a lockout setting. Verify you are in the correct mode (heat, cool, em heat, or auto).
• If you are in the correct mode but cannot set the heat from 40 °F to 90 °F (4.5 °C to 32 °C), or cool from 50 °F to 99 °F (10 °C to 37 °C), maximum or minimum setpoint limits may be restricting your setting. Check with the installer.

Important Safety Information

CAUTION: Equipment damage hazard. To prevent possible compressor damage, do not operate the cooling system when the outdoor temperature is below 50°F (10°C).