Honeywell Home FocusPRO P200 Series Thermostat

User Guide

Model numbers: TH2110U4004, TH2320U4006

For the complete Owner's Manual, search online for Resideo 33-00691EFS.

Thermostat Controls

Time: Displays current time.

Mode: Selects system mode: Heat, Off, Cool, Auto, EM Heat (Emergency Heat).

Menu: Press to access options and start program schedule setup.

Fan: Selects fan mode: Auto, On, Circulate.

Actual indoor temperature: Shows the current indoor temperature.

System status: Indicates system status: Cool On, Heat On, Aux Heat On.

Indoor temperature setpoint: Displays the target temperature. Press [Up Arrow] or [Down Arrow] to adjust.

Temperature/Navigation: Used to increase/decrease temperature setpoint and navigate menus.

Schedule information: Indicates if the thermostat is following a time-based schedule.

System Operation Settings

1. Press the [Mode] button to cycle through available System modes (e.g., Heat, Off, Cool).
2. Stop when the desired System mode is displayed to activate it.

Fan Operation Settings

1. Press/release the [Fan] button to cycle through available Fan modes.
2. Stop when the desired Fan mode is displayed.

Fan modes: Auto (fan runs only when heating/cooling is on), On (fan is always on), Circ (fan runs approximately 33% of the time for air circulation).

Set the Time and Date

Set Time

1. Press [Menu] on the thermostat.
2. Press [Up Arrow] or [Down Arrow] to select TIME, then press [Select].
3. Press [Up Arrow] or [Down Arrow] to choose 12 or 24-hour format, then press [Next].
4. Press [Up Arrow] or [Down Arrow] to adjust the hour, then press [Next].
5. Press [Up Arrow] or [Down Arrow] to adjust the minute, then press [Save & Exit].

Set Date

1. Press [Menu] on the thermostat.
2. Press [Up Arrow] or [Down Arrow] to select DATE, then press [Select].
3. Press [Up Arrow] or [Down Arrow] to choose YEAR, then press [Next].
4. Press [Up Arrow] or [Down Arrow] to adjust the MONTH, then press [Next].
5. Press [Up Arrow] or [Down Arrow] to choose DATE, then press [Save & Exit].

Alerts and Reminders

When an alert is active, the [Alert Icon] (A) appears on the display with the alert number. When the filter reminder is active, the [Filter Icon] appears with number 181.

To Adjust Program Schedules

1. Press [Menu] on your thermostat. Press [Up Arrow] or [Down Arrow] until SCHED is displayed. Press [Select].
2. A square appears around ON or OFF. To use a schedule, press [Up Arrow] or [Down Arrow] to select ON. Press [Next] to edit the schedule or [Exit] to leave the menu.
3. If editing the schedule, press [Next] to edit the day(s) flashing on the display.
4. The word 'Wake' should be flashing. Press [Next]. Press [Up Arrow] or [Down Arrow] to turn this schedule period ON or OFF. Press [Next].
5. If the schedule period is set to ON, the time will flash. Press [Up Arrow] or [Down Arrow] to adjust the time for this period. Press [Next].
6. The Heat setpoint will flash. Press [Up Arrow] or [Down Arrow] to adjust the Heat setpoint for this period. Press [Next].
7. The Cool setpoint will flash. Press [Up Arrow] or [Down Arrow] to adjust the Cool setpoint for this period. Press [Next].
8. The display will show the next schedule period flashing. Repeat steps 4-7 for other periods and days.
9. Press the [Save & Exit] button.

Troubleshooting

Display is blank

• Check circuit breaker and reset if necessary.
• Ensure power switch at heating and cooling system is ON.
• Make sure furnace door is closed securely.

'Waiting for Equipment' appears on the screen

• Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely without damaging the compressor.

Temperature settings do not change

• If display says 'unlock', the thermostat owner has set a lockout. Verify you are in the correct mode (Heat, Cool, Em Heat, or Auto).
• If in the correct mode but unable to set temperature within the range (Heat 40-90°F / 4.5-32°C, Cool 50-99°F / 10-37°C), maximum or minimum setpoint limits may be restricting settings. Check with the installer.