Style Selections 9-Inch Battery-Powered LED Speaker Lantern

Welcome

Thank you for purchasing this Style Selections product. These instructions are designed to help you enjoy the product quickly and easily.

❓ Questions, problems or missing parts? Before returning, contact us on: ? 1-866-994-4148, 8 a.m. - 8 p.m. EST, Monday - Sunday or ascs@lowes.com

For more information, visit Lowes.com, search the item number, and refer to the Guides & Documents tab on the product's page.

Troubleshooting

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

? DANGER: ELECTRIC SHOCK HAZARD! MAY CAUSE SERIOUS INJURY OR DEATH.

? TURN OFF THE POWER SUPPLY TO THE CIRCUIT BREAKER BEFORE INSTALLATION.

⚠️ WARNING: INGESTION HAZARD: This product contains a button cell or coin battery.

• DEATH or serious injury can occur if ingested.

• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.

? KEEP new and used batteries OUT OF REACH of CHILDREN.

? Seek immediate medical attention if a battery is suspected to be swallowed or ingested inside any part of the body.

RF Exposure Information

? RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC Caution

⚖️ FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• -Reorient or relocate the receiving antenna.
• -Increase the separation between the equipment and receiver.
• -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• -Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Package Contents

• A: 9-Inch Battery-Powered LED Speaker Lantern (x1)
• B: USB Cable (x1)
• C: Remote Control (x1)

Product Overview & Charging

Overview

The lantern features LED lighting and a Bluetooth speaker.

Charging

Before use, charge the battery for at least 3 hours with the provided USB cable:

1. Connect the USB cable to a computer USB port or a 5-volt output charger.
2. Connect the USB cable to the product's USB port.
3. The charging indicator will be ? RED while charging.
4. The charging indicator will turn ? GREEN after the battery is fully charged.
5. Disconnect the external adapter from power when not in use.

Charging Port: Located on the product.

Operation

Device Power

Turn on the power: ? There will be a "Power on" prompt sound and a warm white light at 100% brightness. The device enters Bluetooth connection mode, and the blue Bluetooth indicator light at the top will flash (slowly). The indicator light turns off after connecting via Bluetooth.

Turn off the power: ? There will be a "Power off" prompt sound and the light will go out.

Device Light Control (Short Press)

Cycle through light modes:

• Warm light 100%
• Warm light 50%
• Warm light 25%
• Color gradient mode
• Follow the music colorful gradient mode
• Lights went out
• Warm light 100%...

Remote Control Functions

Note: Remove the small plastic sheet from the battery cover before using the remote control. Return this plastic sheet to the remote control when not using to save battery power. Ensure the product is turned on before activating remote control functions.

1. Brightness up: ⬆️ Increase light brightness.
2. Brightness down: ⬇️ Decrease light brightness.
3. LED lights on/off: ?/? Toggle LED lights.
4. Bluetooth on/off: ? Toggle Bluetooth connection.
5. Red LED light: ? Activate red LED.
6. Green LED light: ? Activate green LED.
7. Blue LED light: ? Activate blue LED.
8. White LED light: ⚪ Activate white LED.
9. Yellow LED light: ? Activate yellow LED.
10. Light Blue LED light: ? Activate light blue LED.
11. Purple LED light: ? Activate purple LED.
12. Hot Pink LED light: ? Activate hot pink LED.
13. Orange LED light: ? Activate orange LED.
14. Previous music: ⏪ Play the previous track.
15. Flash-Dancing LED colors along with Music: ? Activate music-sync flashing LED colors.
16. Cyan LED light: ? Activate cyan LED.
17. Volume down: ? Decrease volume.
18. Play/Pause: ▶️ Play or pause music.
19. Volume up: ? Increase volume.
20. Timer for colors: ⏱️ Set timer for LED lights.
    • 1st press: Red color for 30 minutes
    • 2nd press: Green color for 60 minutes
    • 3rd press: Blue color for 90 minutes
    • 4th press: Yellow color for 120 minutes
    • 5th press: Cyan color for 150 minutes
    • 6th press: Violet color for 180 minutes

    Note: Power off the light speaker to cancel the timer.

21. Next music: ⏩ Play the next track.
22. Smooth Automatic smooth transition of LED colors: ? Activate automatic smooth color transition.

TWS Pairing (True Wireless Stereo)

To enable TWS pairing mode: ? Long press the 'Previous music' button (button 14) for 3 seconds. The Bluetooth indicator will flash rapidly. The speaker you long-press becomes the parent speaker.

After successful connection: The indicator light of the parent speaker will flash slowly, and the indicator light of the child speaker will turn off.

To disconnect TWS: When there is an existing TWS connection, long-press the child speaker's button 14 to disconnect.

Note: TWS has a memory function and will automatically connect when powered on next time.