Govee H5053+H5041 Wireless Thermo-Hygrometer with Wi-Fi Gateway

At a Glance

RF Wi-Fi Gateway

• Wi-Fi Pairing key: For pairing the network and the gateway.
• 433 Pairing key: For pairing the sensor and the gateway.
• LED indicator: Reflects the status of the gateway.
  • Blue light is always on: Wi-Fi connection is normal.
  • Red light is always on: Wi-Fi connection failed.
  • Blue light flashes slowly: Wi-Fi pairing mode.
  • Red and blue lights flash alternately: Searching for sensor.
  • Blue light flashes quickly: The gateway is connecting.

Waterproof Thermo-Hygrometer

Specifications

RF Wi-Fi Gateway

• Voltage: AC110-240V 50/60Hz
• Wi-Fi frequency: 2.4Ghz
• Wi-Fi working distance: 30m/100ft
• RF working frequency: 433MHZ
• RF working distance (in open ground): 100m/328ft

Waterproof Thermo-Hygrometer

• Voltage: DC 3V
• Working distance (in open ground): 100m/328ft
• Accuracy: Temp: ±0.3°C, Humidity: ±3%
• Operating temperature: -20°C~60°C (-4°F ~140°F)
• Operating humidity: 0% - 99%

Installation

1. Plug the gateway into the socket.
2. Pull out the battery insulation sheet from the sensor.
3. Place the sensor.

Govee Home App

What you need:

• A Wi-Fi router supporting 2.4GHz (not 5 GHz) and 802.11 b/g/n bands.
• A smartphone or tablet running iOS 9.3 or above, or Android 4.3 or above.

Download the GoveeHome app from the App Store or Google Play.

Connection

Note: Ensure your Wi-Fi network is 2.4GHz and 802.11 b/g/n bands before connecting.

1. Connect your phone to your family Wi-Fi network.
2. Open the GoveeHome app, tap the '+' icon, and select "H5041" or "H5053".
3. Press the Wi-Fi pairing button on the gateway for 3 seconds until the blue light flashes slowly.
4. Enter your Wi-Fi information in the app.
5. Go to your phone's Wi-Fi settings and connect to "Govee_gateway_XXXX".
6. Return to the app. The gateway will connect, indicated by a quickly flashing blue light.
7. Connection succeeded: The blue light on the gateway will remain solid.
8. Connection failed: The red light on the gateway will remain solid. Please recheck the steps and try again.

Using Your Device

Control your devices with the Govee-Home app.

Gateway receives the signal:

Blue light flashes quickly.

Add sensor:

1. Gateway enters pairing mode (press button for 3s, red and blue indicators flash alternately).
2. Sensor sends the pairing signal.
3. Gateway receives the signal (blue light flashes quickly).
4. Connection succeeded (blue light stays bright).

Note: If pairing is not successful within 30s, the gateway will exit pairing mode. If connection fails, recheck the steps.

Calibration:

Calibrate temperature/humidity data within the app.

Message Alert:

The app sends alert messages when temperature/humidity exceeds preset ranges.

Export Data:

Export data in CSV format after providing an email and time slot.

Unit Switch:

Switch temperature units (°F / °C) in the app. The export data will use the same unit as the app.

Troubleshooting and Warning

Troubleshooting

1. Gateway not connecting to Wi-Fi or unstable connection:
   • Ensure you are using a 2.4 GHz network.
   • Verify network name and password, avoid special characters.
   • Place the device within router signal coverage (within 30m/100ft).
   • Minimize obstructions like metal doors or thick walls.
2. Sensors not working:
   • Pull out the insulation sheet.
   • Check battery capacity.
   • Ensure the sensor is installed correctly.
3. Delayed or no app alarm:
   • Enable necessary permissions for the "GoveeHome" app.
   • Reduce distance and obstructions between sensor and gateway.
4. Sensor faults or data missing:
   • Reduce distance and obstructions between sensor and gateway.
   • Remove and re-pair H5053 devices in the app.
   • Replace the battery.

Warning

• Ensure the product operates within the specified temperature and humidity ranges.
• Do not disassemble the product violently.

Customer Service

• Warranty: 12-Month Limited Warranty
• Support: Lifetime Technical Support
• Email: support@govee.com
• Official Website: www.govee.com
• Social Media: @Govee, @GoveeOfficial

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.