BRESSER RC Colour Weather Station with Frameless Display

Finding Information in Other Languages

Visit our website to find further information on this product or available translations of these instructions. You can use the following QR code or web link:

www.bresser.de/P7007620

Warranty Information

For warranty terms and conditions, please visit:

www.bresser.de/warranty_terms

(Multilingual warranty terms: ZÁRUKA · GARANTIE · WARRANTY · GARANTÍA · GARANZIA)

About This User Manual

Please read the safety instructions in this manual carefully. To prevent damage to the device and risk of injury, use this product only as described in the user manual. Keep the user manual accessible to easily find information about all functions.

General Safety Warnings

DANGER! This symbol precedes any part that warns of a risk of slight to severe injury due to improper use.

CAUTION! This symbol precedes any part that warns of a risk of material or ecological damage due to improper application.

DANGER! This device contains electronic components powered by an energy source (power adapter and/or batteries). Use is permitted only as described in the manual; otherwise, there is a RISK OF ELECTRIC SHOCK!

Keep batteries out of reach of children! When inserting batteries, observe the correct polarity. Empty or damaged batteries can cause burns upon contact with skin. If necessary, use suitable protective gloves.

CAUTION! Do not disassemble the device! In case of a defect, contact your specialist dealer. They will contact the service center and, if necessary, may send the device for repair. Do not expose the device to temperatures above 60 °C!

Do not expose the device to high temperatures. Use only the supplied power adapter or recommended batteries. Do not short-circuit the device or batteries, and do not throw them into fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!

Use only recommended batteries. Always replace weak or depleted batteries with a completely new set of batteries with full capacity. Do not use batteries of different brands, types, or capacities. Remove batteries from the device if it is not used for a longer period.

Scope of Delivery

• Colour Weather Station
• Sensor 7009985
• 2 x AAA batteries (not included)
• EU-UK adapter

Main Unit Display Overview

The main unit display shows various information. The numbered items correspond to the display elements:

Control Buttons

The buttons on the device are used for various functions:

Main Functional Sensor

The wireless outdoor sensor has the following components:

• A. Temperature: Displays the measured outdoor temperature.
• B. Current Channel: Shows the selected transmission channel.
• C. Humidity: Displays the measured outdoor humidity.
• D. LED INDICATOR: Flashes during transmission.
• E. Wall Mount: For mounting the sensor on a wall.
• F. Reset: Button to reset the sensor.
• G. Transmission Channel (1-3): Switch to select the transmission channel.
• H. Battery Compartment for 2x AAA: Holds the batteries for the sensor.

Power Adapter

The power adapter set includes:

• 1. Adapter with Euro plug
• 2. Adapter with UK plug
• 3. Adapter holder
• 4. Locking button
• 5. DC connector

Setting up Power Connection

Main Unit:

1. Insert the DC plug into the device's connection port.
2. Plug the power adapter into the socket.
3. The device will be powered directly.
4. Wait until the indoor temperature is displayed on the base.

NOTE: For continuous operation, mains power is recommended. Alternatively, battery power can be used to retain time settings in case of a power outage (permanent backlight will not be active).

Battery Backup:

1. Remove the battery compartment cover.
2. Insert batteries into the battery compartment. Ensure correct polarity (+/-).
3. Replace the battery compartment cover.
4. Wait until the indoor temperature is displayed on the base.

NOTE: On battery power, the display switches to power-saving mode after 7 seconds. Press the SNOOZE/LIGHT button to activate the display for approximately 7 seconds.

NOTE: When switching between mains and battery power, or vice versa, the power supply will be temporarily interrupted for technical reasons. Exception: continuous battery operation.

Wireless Sensor:

1. Remove the battery compartment cover.
2. Set the channel selection switch to the desired channel.
3. Insert batteries into the battery compartment. Ensure correct polarity (+/-).

NOTE: This weather station can be used with one or more remote sensors. Each connected wireless sensor must be set to a different channel. If only one wireless sensor is connected, it should be set to channel 1.

4. Replace the battery compartment cover.

Time Setting

After connecting power, the device automatically searches for the radio signal. This process takes approximately 3-8 minutes. If the radio signal is received successfully, the date and time will be set automatically, and a reception symbol ? will be displayed. If the radio signal is not received, proceed as follows:

1. Press and hold the [Radio Signal] button ? on the main unit for approximately 3 seconds to activate radio signal reception. Reception will now be re-initialized.
2. If the radio signal is still not received, the time must be set manually.

Manual Time Setting:

1. Press and hold the [Time Setting] button for approximately 3 seconds to enter time setting mode.
2. The digits to be set will flash.
3. Press the [Up Arrow] ↑ or [Down Arrow] ↓ button to change the value.
4. Press the [Mode/Set] button to confirm and proceed to the next setting.
5. Setting order: Time Zone > 12/24 h Format > Hour > Minute > Year > Day/Month > Month/Day > Month > Day > Language > °C/°F > hPa/inHg
6. Finally, press the [Mode/Set] button to save settings and exit setting mode.
7. In normal mode, press the [Year] button to check the year.

Alarm Setting

1. In normal mode, press the [Alarm] button ⏰ to check the alarm time.
2. While checking the alarm time, press the [Alarm] button ⏰ again to turn the alarm on or off.
3. To enter alarm setting mode, press and hold the [Alarm] button ⏰ for approximately 3 seconds. The digits to be set will flash.
4. Press the [Up Arrow] ↑ or [Down Arrow] ↓ button to change the value. Press the [Mode/Set] button to confirm and proceed to the next setting. Setting order: Hour > Minute
5. Finally, press the [Mode/Set] button to save settings and exit alarm setting mode.
6. When the alarm sounds, press the [Snooze/Light] button ? to activate the snooze function. The alarm sound will resume after 5 minutes.
7. When the alarm sounds, press any other button to stop the alarm until the next scheduled alarm time.

Max/Min Temperature & Humidity Recording

1. In normal mode, press the [Down Arrow] ↓ button to check the recorded maximum and minimum temperature and humidity.
2. While checking Max/Min data, press and hold the [Down Arrow] ↓ button to clear the data.

Channel Selection

1. In normal mode, press the [Channel] button ? to select Channel 1, Channel 2, Channel 3, or channel scanning.
2. Press and hold the [Channel] button ? for approximately 3 seconds to reset values and search for RF signal.

NOTE: Always ensure that the selected channel on the display unit matches the channel selected on the outdoor sensor.

Backlight

When powered by the power adapter, press the [Light] button to select the backlight level. The backlight can be set to three levels (low, medium, high).

When powered by batteries, press the [Light] button to activate the backlight for 7 seconds.

Temperature Alarm

1. In normal mode, press the [Alarm] button ⏰ to check the HI/LOW temperature alarm.
2. When checking the alarm, press the [Up Arrow] ↑ or [Down Arrow] ↓ button to turn the temperature alarm on or off.
3. In normal mode, press and hold the [Alarm] button ⏰ for approximately 3 seconds to enter temperature alarm setting mode. Press the [Up Arrow] ↑ or [Down Arrow] ↓ button to adjust the temperature. Press the [Mode/Set] button to confirm and proceed to the next setting.
4. Setting order: Highest outdoor temperature > Lowest outdoor temperature > Highest indoor temperature > Lowest indoor temperature
5. Press the [CH] button ? to select the channel, then press and hold the [Alarm] button ⏰ to set the temperature alarm for the correct channel.
6. The alarm will sound and the temperature alarm symbol will flash until the temperature drops below or rises above the set value.

Frost Warning

If the outdoor temperature is between -1.0 °C and +2.9 °C, a frost warning symbol ❄️ will appear on the display and flash continuously.

NOTE: The main unit can be connected to up to 3 outdoor sensors. If the temperature of any sensor is between -1.0°C and +2.9°C, the main unit will display the frost warning symbol ❄️. The symbol will stop flashing when the temperature rises above 3 °C.

Temperature Trend

The temperature trend indicator shows the forecast of weather changes for the coming minutes. Arrows indicate an upward ↑, stable, or downward ↓ trend. The barometer measures air pressure every 15 minutes. Based on this measurement, the main unit calculates the air pressure for the current hour (average pressure now, 15 minutes ago, 30 minutes ago, and 45 minutes ago) and compares it to the previous hour's value. If the measured pressure changes by more than 1 hPa, an upward (UP) or downward (DOWN) trend arrow will be displayed.

Comfort Indicators

Weather Forecast

The weather trend for the next 12-24 hours is calculated from measured values and is graphically displayed as follows:

Moon Phases

Moon phases depend on the current date. They are calculated automatically and displayed using the following symbols:

Barometer

Atmospheric pressure (referred to as "air pressure") is the pressure exerted at any point on Earth by the weight of the air column above it. Air pressure is proportional to the average pressure and gradually decreases with altitude. Meteorologists use barometers to measure air pressure. Since weather depends to a large extent on changes in air pressure, weather forecasts can be generated based on measured pressure changes. The barometer cannot be adjusted. The air pressure unit can be set. (See also manual time setting).

Day of the Week Display

The main unit displays the day of the week. Example displays:

GE SO MO DI MI DO FR SA
FR DI LU MA ME JE VE SA
ES DO LU MA MI JU VI SA
IT DO LU MA ME GI VE SA
NE ZO MA DI WO DO VR ZA
DA SO MA TI ON TO FR LO
EN SU MO TU WE TH FR SA

Daylight Saving Time (DST)

The main station automatically switches to daylight saving time at the beginning of the period.

Low Battery Indicator

If the battery charge level in the main unit or wireless sensor reaches a critical value, the low battery symbol ? will appear in the corresponding area on the display.

When replacing batteries, always remove the batteries from the other device and insert new batteries in the correct order. Replace the batteries being replaced with a completely new set with full capacity. This ensures that the connection between the devices is re-established correctly.

Note: If the batteries are full, no battery symbol is displayed.

Technical Specifications

Main Unit

• DCF
• Batteries: 2 x AAA batteries (not included in delivery).
• EU-UK adapter included in delivery.
• Temperature unit: °C / °F
• Temperature display range: 0 °C – 50 °C
• Humidity display range: 20% ~ 95% RH

Outdoor Sensor

• Batteries: 2 x AAA batteries
• Temperature unit: °C / °F
• Temperature display range: -40 °C – 60 °C
• Humidity display range: 20% ~ 95% RH
• Range: 80 m

EU Declaration of Conformity

Bresser GmbH hereby declares that the radio equipment type with catalog number 7007620 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/7007620/CE/7007620_CE.pdf

Disposal

Sort packaging materials by type. When disposing of the device, please observe the applicable legal regulations. Information on correct disposal can be obtained from municipal waste management services or the environmental department.

Do not dispose of electronic devices in municipal waste! According to Directive 2002/96/EC of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE) and its implementation in German law, used electrical equipment must be collected separately and recycled in an environmentally friendly manner.

According to regulations on batteries and accumulators, disposal in normal municipal waste is expressly prohibited. Please dispose of used batteries in accordance with the law – at a local collection point or from the dealer. Disposal in municipal waste violates the battery directive. Batteries containing toxic substances are marked with a symbol and chemical code.

"Cd" = Cadmium, "Hg" = Mercury, "Pb" = Lead.

• ¹ Battery contains cadmium
• ² Battery contains mercury
• ³ Battery contains lead

Warranty

The standard warranty period is 2 years and begins on the day of purchase. To utilize the extended, voluntary warranty period stated on the packaging, registration on our website is required. Full warranty conditions, information on extending the warranty period, and details about our service can be found at www.bresser.de/warranty_terms.

Contact Information

Bresser GmbH

Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de

Bresser UK Ltd.

Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain

Follow us on social media: f @BresserEurope