Primo 601213 Heavy Duty Bottled Water Dispenser

Quick Start Guide

1. Step 1: Placement

   Place the dispenser on the floor in the desired location. If the surface is uneven, rotate the back feet to level out the dispenser.

2. Step 2: Drip Tray

   Slide the drip tray into place.

3. Step 3: Probe Cleaning

   Clean the probe with a damp cloth and dish soap. (Visit www.primowater.com for detailed cleaning instructions.) Place the probe assembly on the hanger inside the door to keep it clean.

4. Step 4: Bottle Setup

   Grab a bottle of Primo® water and fully remove the cap. Insert the probe assembly into the bottle. Press firmly to secure the assembly over the bottle opening. For 3 and 4-gallon bottles, squeeze the tabs on the top of the probe assembly to separate the probe cap from the collar and press the collar securely over the bottle opening.

5. Step 5: Place Bottle

   Slide the bottle inside the cabinet and close the cabinet door.

6. Step 6: Power Connection

   Plug the dispenser into a ground fault circuit interrupting (GFCI) outlet. You will hear the dispenser begin to pump water to fill the internal hot and cold tanks.

7. Step 7: Activate Functions

   Turn on desired functions by flipping the switches on the back of the dispenser to the ON position. Blue [blue indicator light] indicates nightlight, Green [green indicator light] chills water, and Red [red indicator light] heats water.

8. Step 8: Initial Flush

   Once the dispenser has stopped filling the internal tanks, dispense and dispose of at least 1 quart (approximately 2 pint glasses) of water.

9. Step 9: Ready for Use

   Your water will be ready to dispense fully chilled in approximately 1 hour [1 HR] or piping hot in approximately 12 minutes [12 MIN].

10. Step 10: Register Warranty

    Register your dispenser at www.primowater.com to activate your warranty.

Operating Instructions

Dispensing Cold Water

1. Water will take approximately 1 hour after initial set up to become completely chilled. The cooling light will turn off once the water has been fully chilled.
2. Press a drinking glass or container against the paddle beneath the blue circle to dispense cold water. Release to stop dispensing.

Dispensing Hot Water

1. Water will take approximately 12 minutes after initial set up to reach its hottest temperature. The heating light will turn off once the water has been fully heated.
2. This water dispenser is equipped with a child safety feature to prevent inadvertent dispensing. To enable dispensing of hot water, press and hold the red lock button then press a mug or container against the paddle directly beneath the red lock button.

CAUTION: This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with hot water. Keep children and pets away from the unit while dispensing. Never allow children to dispense hot water without proper and direct supervision. Disable the heating feature by switching the heating convenience switch on the back of the unit to the off position or unplug the unit.

Replacing the Bottle

When your bottle is empty, the empty bottle light will flash. To prevent freeze-up or over-heating, the dispenser will not heat or cool water when the bottle light is flashing. Replace the bottle as soon as possible to re-enable cooling and heating.

1. Open the dispenser cabinet door and slide the empty bottle out of the cabinet.
2. Remove the probe assembly from the empty bottle and place it on the probe hanger.
3. Set the empty bottle aside.
4. Remove the entire plastic cap from the new bottle.
5. Place the probe into the bottle and slide the collar down until it clicks into place. Press on the top of the probe until the tube touches the bottom of the bottle.
6. Slide the bottle into the cabinet and close the door.

Cleaning & Maintenance

For best taste, performance, and hygiene: Clean your cabinet, controls, bottle probe, and spout each time you replace your water bottle. Use a clean, soft cloth and food-grade sanitizer or bleach.

Empty and clean the drip tray as needed. Visit www.primowater.com for detailed cleaning instructions.

Limited Warranty

Primo Water Corporation ("Vendor") warrants to the original purchaser of this dispenser, for a period of two (2) years from the date of purchase, that all parts shall be free from defects in material and workmanship, provided the dispenser is assembled and operated according to the instructions. Proof of purchase (sales slip or invoice) is required.

The warranty is limited to repair or replacement of defective parts. Contact Primo Water's Customer Service Department before returning any parts. Transportation charges for returned parts must be prepaid by the customer; replacement parts will be shipped freight or postage prepaid.

The Limited Warranty does not cover failures or difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation, improper maintenance or service, or failure to perform routine maintenance. It also does not cover cosmetic damage such as scratches, dents, discoloration, or rust after purchase.

This Limited Warranty is in lieu of all other express warranties. Primo Water disclaims all warranties for products purchased from unauthorized sellers. After the two-year period, Primo Water disclaims all implied warranties, including merchantability and fitness for a particular purpose. Primo Water shall not be liable for any special, indirect, punitive, incidental, or consequential damages.

This warranty gives purchasers specific legal rights, and other rights may vary by jurisdiction.

Features

• Convenience Switches: On/off switches for heating, cooling, and nightlight are located on the back of the dispenser.
• Empty Bottle Light: Blinks red when the bottle is empty and needs to be replaced.
• Cooling Light: Solid green when water is cooling. Light turns off when water is fully cooled.
• Heating Light: Solid green when water is heating. Light turns off when water is fully heated.
• Power Light: Solid green when the dispenser is powered on.
• Cold Water Paddle Control: Press a drinking glass or container against the paddle to dispense. Release to stop.
• Night Light: LED night light with an on/off switch.
• Hot Water Paddle Control with Child Safety Feature: Push the red button and press a mug or container against the paddle to dispense. Release to stop.
• Probe Hanger: Rest the probe assembly on the hanger (located inside the cabinet door) to keep it clean while replacing bottles.
• Probe Assembly: Probe pumps water from the bottle into the hot and cold tanks.
• Drip Tray with Full Indicator: Removable and dishwasher safe. A red indicator rises when it's time to empty.
• Water Bottle: Not included. Uses 3-5 gallon bottles. Visit www.primowater.com to find Primo® Water at a store near you.
• Adjustable Feet: Rotate the feet on the rear of the dispenser base to adjust and level.