JONATHAN Y JYL1306A Linear LED Pendant Light
WARNING
- WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
- SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
- INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
- To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
- Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item.
- This item should be assembled on a soft surface to prevent scratching the finish during assembly.
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation.
- The external flexible cable or cord of this luminaire cannot be replaced.
- If the cord is damaged, the luminaire shall be destroyed.
Part List and Hardware List
| Piece | Description | Picture | Quantity | Piece | Description | Picture | Quantity |
|---|---|---|---|---|---|---|---|
| A | mounting screw | mounting screw | 2X | F | canopy | canopy | 1X |
| B | mounting plate | mounting plate | 1X | G | screwed ball | screwed ball | 2X |
| C | machine screw | machine screw | 2X | H | tube | tube | 12" - 4X 6" - 4X |
| D | ground screw | ground screw | 1X | I | body | body | 1X |
| E | wire connector | wire connector | 3X | J | bulb | bulb | 4X |
Diagram of Fixture Components
A visual representation of the JONATHAN Y JYL1306A lighting fixture, showing the main body, connecting tubes, canopy, and hanging hardware.
Product Information
Model#: JYL1306A
Product Dimensions: 34"L X 12"W X 17.75"H
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
- Thread mounting screws (A) into the matching holes of the mounting plate (B), then fix the mounting plate (B) to the outlet box with machine screw (C).
- Loosen the hex nut of the canopy (F), separate swivel from canopy (F).
- Connect the tubes (H) together to get desired length and fix the bottom end to the nipple of the body (I), the top end to the swivel of the canopy (F).
- Place the swivel onto the canopy (F), then secure with the hex nut.
- Make wire connections, with wire connectors (E), following the reference chart listed below.
Wire Connection Chart
| Connect, Hot, Black or Red Outlet Supply Wire to: | Connect, Neutral, White Outlet Supply Wire to: | ||
|---|---|---|---|
| Black | Parallel Cord (round & smooth) | White | * Parallel Cord (square & ridged) |
| Clear, Brown, Gold or Black without Tracer (colored stripes) | Insulated Wire (not green) with copper metal conductor | Clear, Brown, Gold or Black with Tracer (colored stripes) | Insulated Wire (not green) with Silver metal conductor. |
*Note: When parallel wire (SPT I & SPT II) is used, the neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth.
Grounding Instructions
- For installation in the United States: Wrap ground wire from outlet box around green ground screw (D) on mounting plate, no less than 2" from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
- For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting plate. Tighten ground screw.
- Orient the ceiling canopy (F) so that the mounting screws (A) protruding from the mounting plate (B) go into the holes in the canopy (F), then secure it with the provided screwed balls (G).
- Install bulb (J). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
Assembly Diagram
An exploded view illustrating the assembly process of the JONATHAN Y JYL1306A pendant light. It shows the connection points for mounting screws (A), mounting plate (B), machine screw (C), ground screw (D), wire connectors (E), canopy (F), screwed balls (G), tubes (H), body (I), and bulbs (J).
Bulb Information
PLEASE USE ON/OFF TYPE "A" BULB MAX 40-WATT OR LED BULB MAX 9-WATT.
THERE ARE 4PCS 4WATT LED BULBS IN THE BOX.
ENJOY YOUR LAMP
