isinwheel GT1 Electric Scooter User Manual

General Safety Warnings

Always wear a helmet and protective gear. Wear closed-toe shoes without heels and ensure laces are tied. Use the scooter only as intended.

• Before each use, check for loose parts, flat tires, signs of damage, or excessive wear. Immediately stop operation and contact the dealer if anything is amiss.
• Start riding slowly to familiarize yourself with the scooter's operation. Begin at the lowest speed and test the brakes gently. Always slow down when going over bumps or rough road surfaces. Bend your knees slightly to absorb these surfaces.
• Keep the scooter away from children. It is not a toy. Riders must be over 14 years old.
• Do not use the electric scooter in heavy rain or on surfaces covered by more than 12 mm (1/2 inch) of water. Do not immerse the scooter in liquids, and do not let liquids come near the battery or electrical components.
• Do not lend the scooter to people who are unfamiliar with its operation. Ensure new riders are familiar with these instructions and wear appropriate safety gear.
• Once you ride in public spaces, you are subject to the same risks as all traffic participants, just like riding a bicycle.
• Other traffic participants may not observe traffic rules or may ride carelessly.
• The faster the scooter, the longer it will take to stop.
• The scooter can slip on slippery surfaces, leading to rider injury. Pay special attention when crossing railway tracks and/or in rain.
• Always use caution, adjust speed to road and traffic conditions, and maintain distance from other traffic participants.
• Be mindful of pedestrians. Do not use the scooter in any way that could endanger pedestrians. Slow down when passing them to avoid accidents.
• You must comply with all local traffic laws and regulations.
• Do not accelerate downhill.
• Do not press the accelerator while walking the scooter.
• Always keep clear of obstacles.
• Do not hang heavy objects on the handlebars.
• Always keep both feet on the deck.
• Always keep both hands on the handlebars.
• Do not ride in traffic lanes or residential areas where both vehicles and pedestrians are permitted. Do not turn the handlebar violently during high-speed riding.
• Do not ride in water deeper than 38 mm (1.5 inches).
• No passengers are allowed, including children.
• Keep your feet away from the rear fender.
• Do not touch the disc brake rotor after braking.
• Do not attempt to go up or down stairs or jump over obstacles.

CAUTION: Like any mechanical component, a vehicle is subject to stress and wear. Different materials and components may react differently to wear or fatigue. If a component's expected lifespan is exceeded, it may break suddenly, potentially causing rider injury. Cracks, scratches, and discoloration in areas of high stress indicate that a component has reached the end of its useful life and must be replaced.

Unpacking and Assembly

Package Contents

Upon opening the package for the GT1 electric scooter, please verify that all items listed below are included:

• 1 x Scooter
• 1 x Charger
• 1 x Tool Kit
• 1 x Spare Headlight Mounting Hardware Kit
• 1 x User Manual

If any item is missing or damaged, please email customer service for assistance. Keep the original packaging for returning the scooter if necessary.

Assembly Steps

1. Lift the stem into the riding position.
2. Close the folding latch until it clicks into place.
3. Remove the four pre-tightened bolts on the handlebar clamp.
4. Position the handlebar in the handlebar clamp.
5. Adjust the handlebar to the desired position and angle. Retighten the handlebar clamp bolts (adjusting the display angle may facilitate bolt tightening).
6. Tighten the display clamp bolts.
7. The scooter is now fully assembled.

▲ Charge the battery fully before the first ride.

Product Overview

The GT1 electric scooter features the following components:

• Accelerator Lever: Controls the speed.
• Front Brake Lever: Activates the front brake.
• Folding Hook: Secures the folded scooter.
• Rear Brake Lever: Activates the rear brake.
• Rear Light and Brake Light: Provides visibility and signals braking.
• Indicator Lights: Show scooter status.
• Kickstand: Supports the scooter when parked.
• Rear Disc Brake: Provides braking power for the rear wheel.
• Ambient Light: Decorative lighting on the sides.
• Blue Spot Light: Additional lighting feature.
• Headlight and Horn: Front illumination and audible warning.
• Folding Latch: Mechanism for folding the scooter.
• Front Disc Brake: Provides braking power for the front wheel.

Display and Buttons

Display

The display shows various indicators:

• Brake Applied: Indicates when the brake is engaged.
• Locked (in App): Shows if the scooter is locked via the app.
• App Connected: Indicates a connection to the mobile app.
• Left Indicator: Shows when the left turn signal is active.
• Cruise Control: Indicates if cruise control is active.
• Right Indicator: Shows when the right turn signal is active.
• Headlight: Indicates if the headlight is on.
• Mode Indicator: Shows the current riding mode (e.g., ECO, STD, TURBO).
• Speed: Displays the current speed in real-time.
• Battery Level: Shows the remaining battery charge.
• ODO: Total distance traveled.
• TRIP: Distance for the current trip.
• Max: Maximum speed reached during the trip.
• AVG: Average speed during the trip.
• Error: Displays error codes.
• H: Indicates motor overheating.

Riding Modes and Maximum Speed

Buttons

• Power Button (⏻): Press and hold for 2 seconds to turn the scooter on/off. The scooter automatically shuts off after 10 minutes of inactivity.
• Mode Button (M): Press to turn on the side ambient lights and press again to turn them off. Press and hold for 3 seconds to access settings when the scooter is on.
• Lights Button (?): Press to turn on the headlight, rear light, red side lights, and blue spot lights. Press again to turn them off.
• Horn Button (?): Press to sound the horn and release to stop.
• Plus Button (+): Press to change the riding mode from 1 to 4 when the scooter is on. The mode resets to 1 upon restart.
• Minus Button (-): Press to change the riding mode from 4 to 1 when the scooter is on. The mode resets to 1 upon restart.
• Signal Buttons (◀️/▶️): Push left or right to activate the indicator lights and spot lights respectively.

Settings

To access settings:

1. Press and hold the "M" button for approximately 3 seconds when the scooter is on.
2. Once in settings, press the "M" button to cycle through setting options: P01, P05, P06, P99, and ODO.
3. When selecting P01, P05, or P06, use the "+" or "-" buttons to adjust the setting. For P99 or ODO, press and hold the "+" button to modify the corresponding settings. The scooter will return to the main screen after modification.
4. After modifying a setting (P01, P05, or P06), press "M" to save and proceed to the next setting.
5. After modifying all settings, press and hold "M" for approximately 3 seconds or wait 5 seconds to save all changes. The settings will be saved, and the scooter will return to the main screen.

Available settings:

• P01: Unit System: 00 for metric, 01 for imperial.
• P05: Cruise Control: 00 for off, 01 for on.
• P06: Start Mode: 00 for zero-start (push-off required), 01 for non-zero start (throttle can be used from standstill).
• P99: Factory Reset: Press and hold "+" for 5 seconds.
• ODO: Reset Odometer: Press and hold "+" for 5 seconds.

App Usage

Scan the QR code or search for "isinwheel" on the App Store (iOS) or Google Play Store (Android) to download the app for more information and functions.

App Registration Steps:

1. Open the application and tap "Register".
2. Select your country or region and enter your email address.
3. Find the verification code sent to your email and enter it in the app.
4. Set a password for your account.
5. Account registration is complete. You are ready to use the application.

Folding and Unfolding

Folding Steps

1. Press and hold the power button for 2 seconds to turn off the scooter.
2. Open the folding latch.
3. Lower the handlebar stem.
4. Adjust the stem or handlebar so the hook latches onto one of the two horizontal bars above the rear fender.
5. The stem can now be used as a handle for carrying the scooter.

Unfolding Steps

1. Unlatch the hook from the horizontal bar.
2. Lift the handlebar into the riding position.
3. Close the folding latch until it clicks into place.
4. The scooter is now fully unfolded.

Rider's Notice

The GT1 electric scooter is a recreational device. However, once used in public areas, it is considered a vehicle and subject to vehicle risks. For your safety, follow the manual's instructions and traffic laws.

Understand that risks cannot be entirely avoided, as others may violate traffic rules or ride carelessly. You are exposed to road accidents similar to walking or cycling. The faster the scooter, the longer it takes to stop. Slippery surfaces can cause loss of balance and falls. Exercise caution, maintain appropriate speed and distance, especially in unfamiliar areas.

Respect pedestrian right-of-way. Do not startle pedestrians, especially children. When passing pedestrians, use the bell to alert them and pass on their left (where applicable). When crossing paths with pedestrians, stay to the right and maintain a low speed. If crossing paths with pedestrians on foot, maintain the lowest speed or dismount.

Strictly follow the safety instructions in this manual. The manufacturer is not responsible for financial losses, injuries, accidents, legal disputes, or conflicts arising from actions that violate user instructions.

Do not lend the scooter to anyone unfamiliar with its operation. Ensure friends know how to operate it and wear safety gear.

Inspect the scooter before each use. If you notice loose parts, low battery warnings, excessive wear, strange noises, malfunctions, or other abnormal conditions, stop riding.

WARNING - Fire Hazard - No user-serviceable parts.

Charging Instructions

• The scooter is fully charged when the charger's LED indicator turns green from red.
• The scooter automatically stops charging once the battery is full due to charge protection. However, do not charge the scooter for more than 24 consecutive hours.
• Do not connect the charger if the charging port is wet.
• Keep the charging port cover closed when not charging.

! For safety, never use a charger other than the official one.

Battery Charging and Safety Precautions

• Be careful when using power outlets to avoid electric shock.
• Do not leave the charger connected for extended periods (over 24 hours).
• Charge the scooter only in a safe, clean, and dry environment. Keep the charger and scooter away from flammable materials as they may overheat.
• Use only original battery packs and chargers supplied with the scooter. Contact the dealer for replacements. Using other models or brands may be unsafe.
• Do not touch any part of the charging port and keep it away from metal objects to prevent short circuits that could damage the battery or cause injury or death.
• Do not place the battery in direct contact with heat or near high temperatures.
• Do not expose the battery to direct sunlight.
• Do not leave the scooter in a car where the battery could overheat.
• Do not puncture the battery with sharp objects. Do not subject it to impact or force.
• Stop charging if the battery does not charge within the approximate charging time, to prevent overheating, rupture, or fire.
• Do not charge the battery at temperatures below 0°C / 32°F or above 40°C / 104°F to avoid compromising performance, causing breakage, overheating, fire, or personal injury/material damage.
• Do not charge the scooter if the charging port is damaged or wet. Do not charge if the battery is hot, smells, leaks excessively, or looks abnormal.
• If the battery leaks and you come into contact with the liquid, immediately rinse thoroughly with water and seek medical attention.
• Never attempt to disassemble, modify, or repair the battery. This risks damaging protective components and safety features, leading to accidents, injury, or material damage.
• Improper handling or use of the battery can lead to reduced performance, shorter lifespan, rupture, ignition, or other incidents, increasing the risk of serious personal injury.
• Do not discharge the battery using products other than the scooter, as this could damage other products or the battery and shorten its lifespan.
• The battery may overheat, rupture, or ignite, causing personal injury or material damage.
• In daily use, avoid recharging the scooter only after the battery is completely depleted. If the battery level is low, recharge the scooter as soon as possible.
• Please charge the scooter every two months to preserve the battery.

Disc Brake Adjustment

To adjust the disc brake:

An hexagonal wrench is required to loosen the cable clamp bolt.

• If the disc brake drags, slide the caliper arm backward along the cable while holding the cable with one hand. Then, retighten the brake caliper bolt.
• If the disc brake is not efficient, the cable is loose. Slide the caliper arm forward along the cable while holding the cable with one hand. Then, retighten the brake cable clamp bolt.

Note: The disc brake may squeak during use until it is broken in. This is normal and does not affect brake function or performance.

To Eliminate Brake Noise

For easier operation, it is recommended to rest the scooter on a desk.

1. Turn off the scooter.
2. Loosen the two brake caliper mounting bolts (not the cable clamp bolt).
3. Reposition the brake caliper so the brake rotor is centered between the pads.
4. After repositioning the brake caliper, retighten the bolts.

Care and Maintenance

Cleaning

• To clean stains on the scooter's body, wipe with a damp cloth. For stubborn stains, use toothpaste and then clean with a damp cloth.
• Do not clean the scooter with alcohol, gasoline, kerosene, or other corrosive and volatile chemical solvents.
• Do not wash the scooter's floorboard with high-pressure water jets. During cleaning, ensure the scooter is off, the charging cable is unplugged, and the charging port's waterproof cover is closed to prevent electric shock or other serious issues.

Storage

• Store the scooter in a cool, dry place at a temperature of -10°C to 35°C (14°F to 95°F) when not in use. In extremely humid environments, internal parts may form condensation or accumulate water, which can quickly damage the battery.
• Store the scooter indoors, as prolonged exposure to UV rays and rainwater can damage cover materials and reduce battery life.
• Charge the scooter every two months to preserve the battery during storage.
• Improper disposal of used batteries can severely damage the environment. Follow local regulations for used battery disposal to protect the environment.

Battery Maintenance

• For safety, use only the original battery pack and charger.
• Fully charge the battery to maximize its lifespan after each use.
• If the battery is low, charge it as soon as possible. Avoid charging the battery after it has been completely depleted.
• Never disassemble or puncture the battery.
• Keep battery contacts away from metal objects to prevent short circuits that could cause battery damage or injury/death.

Battery Disposal

• Do not dispose of the battery via landfill, incineration, or household waste.
• It is recommended to dispose of the battery through a local recycling program suitable for lithium-ion batteries. For more information, contact your local waste management service.
• Improper handling of used batteries can severely damage the environment. Comply with local laws and regulations for proper disposal of used batteries.

Specifications

Notes:

• (1) Height: From the ground to the highest point of the body.
• (2) Range: Measured under full charge conditions, with a load of 70 kg (154 lbs), at 25°C (77°F), on a flat road without wind, and at a speed of 15 km/h (9.3 mph). Actual range varies based on factors like load, humidity, wind speed, and operating habits.
• (3) Maximum load must always be kept within 150 kg (330 lbs) (including rider and personal items). Consider the additional weight generated by speed.

Limited Warranty Statement

30-Day Satisfaction Guarantee Return Policy

If you are not satisfied with your purchase, the return policy allows you to return the product purchased through an authorized channel within 30 days of receiving the shipment for a refund from the authorized channel for any reason. The seller is not responsible for lost packages due to the courier or for products received that cannot be verified. Products received with damage deemed to be caused by the end-user may be subject to rejection of the return request.

Conditions for Refund:

1. A Return Merchandise Authorization (RMA) must be requested within 30 days of receiving the shipment. Email the support team to request an RMA.
2. Return shipping costs are the customer's responsibility.
3. For warranty service, keep your receipt and/or invoice as proof of purchase.
4. The returned product must be in good physical condition (not broken or damaged).
5. All accessories originally included with the purchase must be included in the return.
6. If a product is returned without an RMA or without all original parts, the seller reserves the right to refuse the return.

Limited Warranty

1. The seller warrants to the original buyer that the product is free from defects in materials and workmanship under normal use for the period specified.
2. The seller does not guarantee uninterrupted or error-free product operation. The seller is not responsible for damages resulting from failure to follow product instructions.
3. Within 180 days of purchasing the scooter, if the battery is defective, it can be replaced free of charge. After this period, the battery replacement is at the customer's expense.
4. Only the original owner of a scooter purchased from the online store is covered by this Limited Warranty. The Warranty Period begins upon receipt of the scooter and ends immediately upon the earlier of the warranty period expiration or the sale or transfer of the scooter to another person. The Limited Warranty will not apply to any subsequent owner or assignee.

The Limited Warranty Does Not Cover:

1. Normal wear and tear of any covered component.
2. Consumables or parts subject to normal wear (including tires, tubes, brake pads, cables, housings, grips).
3. Any damage or defects to covered components resulting from failure to follow the user manual instructions, force majeure, accidents, improper use, negligence, abuse, commercial use, alterations, modifications, incorrect assembly, installation of non-original or incompatible parts, operator error, water damage, extreme riding, acrobatic riding, or improper maintenance.
4. Unauthorized repairs or use of unauthorized parts.
5. Battery damage resulting from voltage surges, use of an inadequate charger, improper maintenance, other misuse, normal wear, or water damage.

Remedies

If a hardware defect is found and a valid claim is received within the warranty period, the seller will, at its discretion and to the extent permitted by law, either (1) repair the product using new or refurbished replacement parts, or (2) replace the product with a new or refurbished one. These are the sole and exclusive remedies for defects. Shipping and handling fees may apply where not prohibited by law. This Limited Warranty is valid only in jurisdictions where products are sold through the official website and to the extent permitted by applicable laws.

Any replacement hardware will be warranted for the remainder of the original warranty period or for thirty (30) days, whichever is longer, or for any applicable period in the customer's jurisdiction.

How to Obtain Warranty Service

A warranty service request must be submitted within the warranty period from the date of shipment receipt. Contact the support team to request a warranty service order. To obtain warranty service, you must deliver the product, in its original packaging or packaging providing equal protection, to the specified address. As per applicable law, proof of purchase and/or registration may be required before receiving warranty service.

Limitation of Damages

To the extent permitted by applicable law, the seller is not liable for any incidental, indirect, special, or consequential damages, including lost profits, revenue, or data, even if informed of such possibility. This applies regardless of whether the claim is based on breach of warranty, contract, tort, or any other legal theory.

Some jurisdictions do not allow the exclusion or limitation of special, indirect, incidental, or consequential damages, so the above limitation or exclusion may not apply.

Questions and Answers

1. Q: What if the scooter arrives with broken or missing parts?
   A: Please take a photo and email it to the support team. They will respond promptly and send the correct replacement part.
2. Q: Are the tires replaceable, and how?
   A: Yes, the tires are replaceable. Contact support for more information or search YouTube for "How to replace scooter tires".
3. Q: What if the disc brake is not functioning correctly?
   A: Please read the "Disc Brake Adjustment" section in this manual or search YouTube for "How to adjust scooter disc brakes". If the problem persists, contact us.
4. Q: What should I do if I hear strange noises from the rear wheel?
   A: Normally, this means the brake disc is warped and causing friction noises. Please refer to the "Disc Brake Adjustment" section in this manual. If the problem persists, contact us.
5. Q: What should I do if an error code appears on the screen?
   A: If you see an error code, contact the support team to resolve it.

Error Codes:

Disposal and Compliance

Electrical and Electronic Equipment Disposal

The crossed-out wheelie bin symbol means you are legally obligated to dispose of these devices separately from unsorted municipal waste. Disposal in residual waste bins or yellow bins is prohibited. If products contain batteries or accumulators that are not permanently installed, they must be removed before disposal and disposed of separately as batteries.

Options for Returning Old Devices (EAR)

Owners of old devices can hand them in as part of the return or collection options for used devices provided by public waste disposal authorities to ensure proper disposal.

Data Protection

We inform all end-users of end-of-life electrical and electronic equipment that they are responsible for deleting personal data from the old devices to be disposed of.

CE Notice

This appliance must not be used by persons (including children) with reduced physical, sensory, or mental capabilities, or without experience and knowledge, unless supervised or instructed by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.

Declaration of Conformity

For the full text of the EU Declaration of Conformity, visit the links:

https://www.iscooterglobal.co.uk/pages/declaration-of-conformity

https://www.iscooterglobal.de/pages/konformitatserklarung

Manufacturer Information:

Shenzhen Xincheng Times Technology Co., Ltd
Address: 104-105, Block C, Donghai Wang Building, No. 369, Bulong Road, Ma'antang Community, Bantian Street, Longgang District, Shenzhen
Email: support@iscooterglobal.eu

EC Representative:

GAVIMOSA CONSULTORIA, SOCIETÀ LIMITATA
Address: CASTELLANA 9144, 28046 Madrid
Email: compliance.gavimosa@outlook.com
Contact: Jorge Wilson
Tel: +34 688185858

UK Representative:

Sea&Mew Accounting Ltd
Address: Electric Avenue Vision 25, London, Enfield EN3 7GD
Email: info@seamew.net
Contact: Billy Han
Tel: +44 7399648608