JBC Instruction Manual

Model: 0032589 Curved Guide Nozzle for ALE250

Product Reference

This manual corresponds to the following references: 0032589 for solder wire ø 0.8-1.2 mm / 0.031-0.047 in.

Packing List

The following items are included:

Curved Guide Nozzle for ALE250: 1 unit
Manual (Ref. 0032591): 1 unit

Features

The curved guide nozzle is designed to be used with the ALE250 Auto Feed Soldering Iron and it works with some of the C245 cartridges. Note: Only cartridges mentioned below are suitable. These cartridges are 20 mm longer than the C245 standard cartridges.

Compatible Cartridges*

Cartridge Ref.	A [mm / in]	B [mm/in]
C245230	ø 0.3 / ø0.012	13.5 / 0.531
C245201	ø 0,6 / ø0.024	9 / 0.354
C245803	ø 1 / 0.039	10.5 / 0.413
C245806	1.2x0.7 / 0.047x0.028	10 / 0.394
C245807	2.2x1 / 0.087x0.039	10 / 0.394
C245845	ø 2.2 / ø0.087	10 / 0.394
C245256	ø 3.5 / 0.138	10.5 / 0.413

*Not included, sold separately.

Changing the Guide Nozzle

Note: If you replace a straight guide nozzle with a curved one, then C250 cartridges must be replaced with C245 cartridges. For compatible cartridges, see page 2.

To change the guide nozzle, unload the solder wire, disconnect the tool from the control unit, and let it cool down. Then detach the clips from the tool cable, loosen the guide set fixation screw (1), and take out the guide set (2).

Diagram Description: Shows a C245 Cartridge connected to the ALE250 tool. The guide nozzle is attached via a guide set, secured by a fixation screw. The connection points are labeled 1 (Guide Set Fixation Screw) and 2 (Guide Set).

Unscrew the guide nozzle (3) from your guide set. Then, unscrew the outlet nozzle (4) and set it apart. If the outlet nozzle is stuck onto the guide nozzle because of the flux, soak it in alcohol to release it.

Diagram Description: Illustrates unscrewing the guide nozzle (labeled 3) from the guide set. It also shows unscrewing the outlet nozzle (labeled 4) separately.

Screw your outlet nozzle (5) onto the new curved guide nozzle and then screw the new guide nozzle (6) onto the guide set. Note: There is an outlet nozzle size for each soldering wire diameter. The use of the nozzle is necessary as its inner diameter is adjusted to the solder wire diameter and guides the wire with greater precision.

Diagram Description: Depicts screwing the outlet nozzle (labeled 5) onto the new curved guide nozzle. The new guide nozzle is then shown being screwed onto the guide set (labeled 6).

Insert the guide set (7) into the tool and adjust its position. Leave a gap of 5 to 7 mm (0.197 to 0.276 in) between the cartridge tip and the outlet nozzle (8). Once the position is adjusted, tighten the fixation screw (9). Use the clips to attach the guide set to the tool cable.

Diagram Description: Shows inserting the guide set (labeled 7) into the tool. A gap measurement (labeled 8) of 5-7 mm (0.197-0.276 in) is indicated between the cartridge tip and the outlet nozzle. The fixation screw (labeled 9) is shown being tightened to secure the guide set to the tool cable.

Specifications

0032589 Curved Guide Nozzle for ALE250

Ref.: 0032589

Suitable Solder Wire Diameter: ø 0.8 to 1.2 mm / 0.031 to 0.047 in
Total Net Weight: 9 g / 0.02 lb
Package Dimensions / Weight (L x W x H): 40 x 55 x 90 mm / 33 g (1.57 x 2.17 x 3.54 in / 0.07 lb)

Complies with CE standards. ESD safe. [Electrostatic Discharge protection symbol]

Warranty and Disposal

Warranty

JBC's 2-year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.

Disposal

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility. [WEEE symbol]

Compliance Logos: CE [European Conformity], EAC [Eurasian Conformity], PSE [Japan Safety Mark]

Website: www.jbctools.com

	JBC T210 & T245 Soldering Handpieces - Reference Guide Comprehensive reference guide for JBC T210 and T245 soldering handpieces, detailing features, compatible cartridges (C210, C245), station compatibility, maintenance, and warranty information.
	JBC AP250 Manual-Feed Soldering Iron Instruction Manual Instruction manual for the JBC AP250 Manual-Feed Soldering Iron, covering packing list, features, connections, cartridge changes, solder reel replacement, feeder nozzle adjustment, compatible cartridges, and accessories.
	JBC B-100 Light Handle for B·IRON: Instruction Manual & Features Comprehensive guide to the JBC B-100 Light Handle for B·IRON soldering system. Covers features, operation, maintenance, and software updates for R&D and individual soldering tasks. Visit www.jbctools.com for more.
	JBC B·IRON Tweezers User Manual and Specifications Comprehensive user manual and technical specifications for JBC B·IRON Tweezers, including models BIP-5HA and BIP-5HQA. Covers features, operation, maintenance, and app connectivity.
	JBC SC Magazine for C210 & C245 Cartridges Instruction Manual Instruction manual for the JBC SC Magazine, designed to hold and organize C210 and C245 soldering cartridges. Details features, packing list, changing cartridges, and specifications.
	JBC SCH Cartridge Holder for Soldering Cartridges Information about the JBC SCH Cartridge Holder, designed for JBC's extensive range of soldering cartridges including C120, C130, C210, C245, C250, C420, C470, C530, and C560. Features a holder with space for over 500 tip shapes.
	JBC B·500 K Handle Expansion Kit for B·IRON: Instruction Manual & User Guide Comprehensive instruction manual for the JBC B·500 K Handle Expansion Kit, designed to extend B·IRON soldering stations. Learn about setup, operation, maintenance, safety, and specifications for enhanced soldering efficiency.
	JBC CDB Compact Soldering Station Instruction Manual Instruction manual for the JBC CDB Compact Soldering Station, detailing its features, operation, maintenance, and safety guidelines.