Introduction
Thank you for purchasing the Aputure Light Dome 150. The Aputure Light Dome 150 is a 150cm (59in) Bowens Mount Quick-Setup Circular Softbox. Its substantial surface area makes it ideal for use with high-powered Bowens Mount LEDs, such as Aputure's LS 600 Series Point Source LED fixtures.
Important Safety Instructions
- Read and understand all instructions before using.
- Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.
- Care must be taken as burns can occur from touching hot surfaces.
- Care must be taken when touching, installing or disassembling the elastic support rod.
- Let the fixture cool completely before storing.
- To reduce the risk of injury, please install or disassemble the fixture properly.
- The use of an accessory attachment not recommended by the manufacturer may increase the risk of fire, electric shock, or injury to any persons operating the fixture.
- Please do not place the fixture near any liquids or other flammable objects.
- Only use a dry microfiber cloth to clean the product.
- This product is certified by RoHS. Please operate the product in full compliance with the operation standards. Please note that this warranty does not apply to repairs arising from malfunctions, although you may request such repairs on a chargeable basis.
- The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design or specifications change.
SAVE THESE INSTRUCTIONS
Detailed product manual for Light Dome 150 can be found on www.aputure.com.
Components List
- Light Dome 150 Circular Softbox (1pc)
- Front Fabric Diffusion (1.5 Stop) (1pc)
- Fabric Light Control Grid (1pc)
- Front Fabric Diffusion (2.5 Stop) (1pc)
- Light Dome 150 Carrying Bag (1pc)
Setting Up the Light Dome 150
To set up the Light Dome 150, lift each of the 16 quick-setup support rods until it clicks and locks into the speedring. Setting up the rods in an alternating pattern is ideal for the longevity of the rods.
[Diagram: A hand lifts a support rod upwards until it clicks and locks into the speedring. An arrow indicates the upward motion.]
Collapsing the Light Dome 150
To collapse the Light Dome 150, lift each of the 16 quick-setup support rods and simultaneously press the quick-release tabs on the speedring. The rods will then be released from the locking mechanism and can be collapsed. Collapsing the rods in an alternating pattern is ideal for the longevity of the rods.
[Diagram: A hand lifts a support rod and simultaneously presses a quick-release tab on the speedring. Arrows indicate the lifting and pressing actions, leading to the rod collapsing.]
Specifications
| Item | Specification / Value |
|---|---|
| Softbox (Collapsed) Dimensions | 186.5mm*1160mm / Φ7.34in*45.66in |
| Softbox (Built) Dimensions | Φ1500mm*800mm / Φ59.06in*31.5in |
| Front Fabric Diffusion 1 (1.5 Stops) Diameter | Φ1420mm / 55.91 in |
| Front Fabric Diffusion 2 (2.5 Stops) Diameter | Φ1420mm / 55.91in |
| Fabric Light Control Grid Diameter | Φ1420mm / 55.91in |
| Speed Ring Adapter Type | Standard Bowens Mount |
| Net Weight | 3.32kg / 7.32lbs |
Trademarks
Bowens is a trademark or registered trademark of Bowens in China or other countries.
Warranty Information
Aputure Imaging Industries Co., Ltd. warrants the original consumer purchaser from defects in material and workmanship for a period of one (1) year after the date of purchase. Keep your original sales receipt. Be sure the dealer has written on it the date, serial No. of the product. This information is required for warranty service.
Warranty does not cover:
- Cosmetic defects that appear more than thirty (30) days after the date of purchase.
- Damage that is the result of misuse, abuse, accident (including but not limited to damage by water), faulty connection, defective or maladjusted associated equipment, or the use of the product with equipment for which it was not intended.
Warranty is void if:
- The product identification or serial No. label is removed or defaced in any way.
- The product is serviced or repaired by any one other than Aputure or an authorized Aputure dealer or service agency.
Contact Information:
- Add: F/3, Building 21, Longjun Industrial Estate, Heping West Road, Shenzhen, Guangdong
- Sales Contact: (86)0755-83285569-613
- E-MAIL: cs@aputure.com
For more details of warranty visit www.aputure.com.
Inspection: Qualified
