HOW TO USE G1

Function Introduction

• Bluetooth 5.0
• Connect to GPS Navigation
• Support Voice Assistants
• Voice prompt
• Hands-free Calling
• Support Hi-Fi Music
• Built-in CVC/DSP Noise Reduction
• Universal Pairing

The G1 is compliant with Bluetooth Specification V5.0 supporting the following profiles: Headset Profile (HSP), Hands-Free Profile (HFP), and Advanced Audio Distribution Profile (A2DP).

Headset: The G1 has a high-definition 40MM stereo headset and an outstanding built-in CVC/DSP intelligent noise reduction microphone. These designs are suitable for most open, face-off, full-face, and off-road helmets.

Battery: The G1 features an 800 mAh battery which can provide the intercom device with 25 hours of music with over one week of standby time.

WARNINGS

PLEASE CHECK ALL LOCAL LAWS AND REGULATIONS REGARDING THE USE OF IN-HELMET SPEAKERS WHILE OPERATING MOTORIZED VEHICLES.

Product Packaging

The G1 package includes the following components:

• Main Unit
• Boom Microphones
• Button Microphones
• 40 MM HD Ultra-Slim Speakers
• USB-C Cable
• Clip Mounting Bracket
• 3M Tape Mounting Bracket
• Speaker Pad
• User Manual

Installation Instructions

Installing Bracket for G1 to Helmet

With Clip Mounting Bracket

Open the clip mounting bracket and insert it into the helmet shell.

With 3M Tape Mounting Bracket

Peel off the protective paper on the back of the 3M tape, then adhere the 3M mounting bracket to a suitable position on the left side of the helmet. Press for 15 seconds to allow the glue 24 hours to dry.

Note: LEXIN recommends using the clip mounting bracket for convenience. The 3M Tape bracket is an option that you may use at your own risk and responsibility.

Mounting the G1 Main Unit

There are two square columns on the back of the G1 main unit and corresponding square holes on the mounting bracket. Align the square column on the back of the main unit with the square hole of the bracket. Slide the main unit down onto the bracket until it clicks firmly into the bottom portion of the bracket.

Remove the G1 Main Unit

To remove the main unit from the bracket, ensure the headset jack is not connected to the main unit, then push the main unit towards the upper left firmly until the main unit slides out from the bracket.

Installing Speakers

Note: The speaker with the shorter wire is for the left ear, and the speaker with the longer wire is for the right ear. Attach the speaker under the protective materials of the helmet. If the preset holes for the speaker of the helmet are too deep, you can use the speaker pads as spacer to make the speakers closer to the ears.

1. Peel off the 3M tape of the speaker and stick it into the helmet's inner padding.
2. Press the speakers firmly against the velcro pads.
3. Hide the wires between the helmet liner padding and shell.

Installing Microphone

Note: The button microphone or boom microphone can be switched between full-face or open-face helmets. Please choose the suitable microphone based on your preference and what fits best with the helmet(s).

Full-face Helmet/Button Microphone

1. Locate a central area of the mouth section of the helmet to install and adhere half of the microphone velcro pad.
2. Attach the button microphone to the attached velcro pad.
3. Connect it to the headphone connector from the left.

Open Face Helmet/Boom Microphone

1. Attach one half of the velcro pad to the base of the microphone and the other half to the inside of the helmet's padding.
2. Adjust the microphone's direction so that the triangular mark points towards your mouth.

Replace the Pattern Shell

1. Remove the old pattern shell from the unit (use a thin object to pry up the pattern shell from the unit, as there is a small gap on the left).
2. Choose one new pattern shell, then align the shell with the main unit and press it until they fit perfectly.

Basic Operation

Diagram Description: The device features a Power Button, Voice Assistant Button, Volume Up/Down Buttons, and a USB-C Charging Port/Headset Port. It also has a Changeable Pattern Shell.

Power On/Off

Power On: Press and hold the Power Button for 2 seconds to power on the device. You will hear a voice prompt "Power On" and the current battery life. The LED indicator flashes red and blue, entering pairing mode automatically.

Power Off: Press and hold the Power Button for 2 seconds. You will hear a voice prompt "Power Off".

Battery

Charging: Plug the USB-C cable into the USB-C port and connect to a DC 5V/1A power supply (e.g., mobile phone charger or power bank). The LED turns red while charging and blue when fully charged. Charging takes approximately 2 hours.

Battery Life Prompt: While in standby mode, press and hold the Voice Assistant Button for 2 seconds to hear the current battery life, which will be reported as HIGH, MEDIUM, or LOW.

Note: When the battery capacity is low, the device will notify you every 15 minutes. It indicates approximately 1.5 hours of use remaining before it turns off.

Pairing G1 with Bluetooth Devices

Note: A single G1 can connect with up to two Bluetooth devices (e.g., two mobile phones or one mobile phone and another Bluetooth device).

Pairing Mobile Phone

1. With the unit powered off, press and hold the Power Button for 2 seconds until the LED indicator flashes red and blue, and the device prompts "pairing" to enter pairing mode.
2. Go to Bluetooth settings on your phone and select "LEXIN G1".
3. Some mobile phones may require a PIN; enter "0000" if required.
4. The LED will blink blue and a voice prompt "Pairing successful" will indicate connection completion. Confirm the pairing on your phone.

Reconnect to the Last Paired Phone

The G1 will automatically reconnect to the last paired phone by default. If the device does not reconnect, click the power button on the device.

Clear Bluetooth Pairing History

With the G1 main unit in standby mode, press and hold the Up Button and the Down Button simultaneously for 2 seconds to clear all pairing history. The LED indicator will flash red and blue three times.

Phone Calls

• Answer Phone Call: Click the Power Button to answer an incoming call.
• End Call: Click the Power Button to end the call.
• Reject Phone Call: Double-click the Power Button to reject an incoming call.
• Voice Dial: While paired with your phone, click the Voice Assistant Button to activate Siri or other voice assistants, using voice commands to contact numbers from your contact list.

Music And Volume Control

• Volume Control: Click the Up/Down Button to adjust the volume. A voice prompt will indicate when the volume reaches maximum or minimum.
• Play/Pause: Click the Power Button to play a song when the unit is powered on. Click the Power Button to pause when music is playing.
• Change Song: Double-click the Up Button to switch to the next song. Double-click the Down Button to switch to the previous song.

Pairing with other Bluetooth Headset

1. With the G1 off, press and hold the Power Button for 5 seconds. The LED indicator flashes red and blue, and the voice prompts "Pairing".
2. Power on the Bluetooth headset from another model and enter its Bluetooth pairing mode based on its instructions.
3. After pairing is complete, the LED indicator flashes blue, and the voice prompts "pairing successful".
4. Start the Bluetooth intercom based on the instructions from the other model.

Note: The G1 cannot actively initiate the intercom.

Maintenance & Certification

Maintenance and Care

Follow these suggestions for optimal care of your LEXIN G1 device and to maintain warranty protection:

• Do not use or store the device in dusty or dirty environments, as moving parts and electronic components can be damaged.
• Do not store the device in high heat areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.
• Do not store the device in cold temperature areas. When the device returns to normal temperature, moisture can form inside and damage electronic circuit boards.
• Do not attempt to open the LEXIN-G1 case. Do not drop or knock the device; rough handling can break internal circuit boards and fine mechanics.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Do not paint the device, as paint can clog moving parts and prevent proper operation.

These suggestions apply equally to the headset main unit, speaker-microphone clamp unit, and power charger.

Warranty

LEXIN warrants that this product shall conform to and perform in accordance with published technical specifications and accompanying written materials, and shall be free of defects in materials and workmanship for a period of two years from the date of purchase by the first consumer purchaser. The limited warranty extends only to the original consumer purchaser and is not assignable or transferable. This warranty is limited to repair or replacement at LEXIN's discretion for defective or unqualified products. LEXIN is not responsible for product failure due to:

• (a) Any incorrect use or misuse of the product.
• (b) Failure to adhere to LEXIN's specifications or instructions.
• (c) Man-made damage caused by neglect, misuse, or accident.
• (d) Damage caused by using auxiliary equipment or software not furnished by LEXIN.

Please return the product to LEXIN or its international distributor where purchased, providing proof of purchase and receipt date to obtain warranty service during the validity period.

Waivers and General Release

By using the product, you waive substantial legal rights. Please read the following carefully before using the device. By using the product, you agree to this agreement and forfeit the right to pursue legal action.

By using the product, you are irrevocably releasing, indemnifying from any liability, loss, claim, and expense (including attorney's fees) and holding LEXIN harmless for any bodily injuries, harm, or death, as well as losses or damages to vehicles or property, resulting from using the product under any circumstances.

You, your heirs, legal representatives, successors, or assigns, hereby voluntarily and forever release, discharge, indemnify, and hold harmless LEXIN from any and all litigation, claims, debts, demands, actions, and liability which may arise, directly or indirectly, from using the product for any distress, pain, suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law.

You fully understand and assume the risks in using the product, including the risk of negligent acts or omissions by others. All risks for operating the product are assumed solely by the user.

You confirm that you are physically capable of using the product, have no medical conditions that may infringe upon your abilities, are at least eighteen (18) years of age, and have been advised of the risks. You further confirm that you will not consume alcohol or any mind-altering substance that may affect your alertness before or during use.

You fully acknowledge our warnings and understand that:

• (a) Risks and dangers exist in using the product while in traffic, including but not limited to injury, illness, strains, fractures, paralysis, death, or other ailments causing serious disability.
• (b) These risks and dangers may be caused by the negligence of manufacturers, their agents, or any third party involved in designing or manufacturing the product.
• (c) These risks and dangers may arise from foreseeable or unforeseeable causes.

You hereby assume all risks and dangers and all responsibility for any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including LEXIN.

By using the product, you confirm that you have read this release of liability and fully understand and accept its terms and conditions.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. This product is in compliance with FCC RF exposure requirements and refers to the FCC website.

Search for FCC ID: 2ARGO-LX G1 at https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

(French text follows) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This EUT is in compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and has been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with a minimum distance of 1cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

(French text follows) Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102 d'Industrie Canada et a été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet appareil doit être installé et utilisé avec une distance minimale de 1 cm entre l'émetteur et votre corps. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.