Gofilm 20 Quickstart Guide

Version: V1.1

How to bind ELRS 2.4G

The flight controller has a built-in ELRS receiver. Power up the Gofilm 20 three times quickly using the battery. When the receiver indicator turns red and flashes twice quickly, it enters binding mode.

Use an ELRS 2.4G protocol remote controller for frequency binding. For example, using the Radiomaster ZORRO ELRS 2.4G remote controller, perform settings as shown in Figures ① and ②. After successful binding, the flight controller's ELRS receiver indicator light will be solid red.

Figure 3: ELRS receiver indicator light

How to bind VTX

1. Connect the Moonlight Kit and the power of the goggles.

2. Briefly press the Moonlight Kit and goggles linking buttons respectively. When the Moonlight Kit enters pairing state, the VTX LED turns red, and the goggles emit a DI... DI... DI... beep.

3. After successful linking, the VTX LED indicator light turns solid green, the beeping sound on the goggles stops, and the screen displays the video feed.

For more information on the Moonlight Kit, please scan the QR code to view the electronic manual.

ARM & Mode

After binding is successful, connect the FC to Betaflight and enter the Modes tab. Toggle the corresponding switch for each function. Moving the yellow cursor of the corresponding auxiliary channel of the switch will turn on the corresponding function when it moves into the set range. Click save after setting.

ARM:

Min: 900
Max: 2100

ANGLE:

Min: 900
Max: 2100

HORIZON:

Min: 900
Max: 2100

BEEPER:

Min: 900
Max: 2100

FLIP OVER AFTER CRASH:

Min: 900
Max: 2100

Pre-flight Check

Turn on the transmitter and select the correct mode. Ensure the arming switch is in the "disarmed" position and the throttle is all the way down.
Check propeller steering direction, smooth rotation, and screw tightness.
Verify sufficient battery power. A fully charged 4S battery is 16.8V.
Ensure the battery is securely attached to the aircraft by the strap and the balance head is secured to prevent contact with the props.
Observe the take-off environment for safety, obstacles, and no-fly zones.
Verify clean, strong video feed in FPV goggles or screen. Resolve any interference or other pilot feeds before flying.

CAUTION!

This product is not a toy and is not suitable for children under 14 years of age. Minors should be accompanied by an adult when operating.
Improper adjustments and operation may result in crashes and damage to the item.
The operator is solely responsible for their actions. Always choose a suitable environment for operating the remote control model, away from public roads, dense crowds, cables, and radio towers.

Default firmware version

ExpressLRS V3.0.1

Default motor rotation direction

This content is subject to change. Download the latest version from https://www.caddxfpv.com

CADDXFPV Support

Email: support@caddxfpv.com

https://www.caddxfpv.com

中文内容 (Chinese Content)

如何对频 VTX:

连接 Moonlight Kit 和眼镜端电源。
等待设备启机后,分别短按 Moonlight Kit 和眼镜端对频按钮,当进入配对状态时, VTX 指示灯变为红色,眼镜端发出滴... 滴... 滴... 蜂鸣器提示。
对频成功后,VTX 指示灯变为绿色常亮,眼镜端蜂鸣器停止并显示图传画面。

更多 MOONLIGHT KIT 产品信息请扫描二维码查看电子说明书。

如何对频 ELRS 2.4G:

飞控板载 ELRS 2.4G 接收机,使用电池给 Gofilm 20 快速通电3次,当接收机指示灯(如图③)变为红灯快闪两次时为进入对频模式。
使用 ELRS 2.4G 协议遥控器进行对频,以 Radiomaster ZORRO ELRS 2.4G 遥控器设置为例,根据图①②进行遥控器设置,对频成功后飞控 ELRS 接收机指示灯为红灯常亮。

解锁开关:

对频成功后,连接 Betaflight 地面站,进入模式选项,尝试拨动遥控器各功能开关,当黄色光标移动到设定范围就会开机相对应的功能,设置完成后点击保存。