Yeelight Motion Sensor Nightlight

Product Overview and Components

This section details the components of the Yeelight Motion Sensor Nightlight.

Key Components:

• On/Off Switch: Controls the power and operating mode.
• Lamp: The light source.
• Sensor: Detects motion.
• USB Charging: Port for charging the device.
• USB Cable: Used for charging.
• Magnetic Disc: For mounting the device.
• Hook: For hanging the device.

Diagram Description: The device is shown with labels pointing to the On/Off switch, lamp, sensor, USB charging port, USB cable, magnetic disc, and hook.

Operation Modes

The device features three operating modes controlled by a switch:

• ON: The light remains continuously illuminated. The sensor light also stays on.
• AUTO: Motion detection mode. The light turns on when motion is detected in darkness and automatically switches off after 15 seconds.
• OFF: Turns the light off.

Diagram Description: A switch labeled "OFF AUTO ON" is shown, indicating the position for each mode.

Installation

Mounting Options:

1. Using the Magnetic Disc:

   Peel the adhesive sticker from the magnetic disc. Attach the disc to your desired mounting surface. Then, attach the lamp to the magnetic disc.

   Diagram Description: Shows peeling a sticker from a circular magnetic disc, then attaching the disc to a surface, and finally attaching the lamp to the disc.

2. Using the Hook:

   Use the provided hook to hang the lamp in your chosen location.

   Diagram Description: Shows the lamp with the hook attached, ready to be hung.

Sensor Specifications

The motion sensor has the following specifications:

• Range: 5-7 meters in front, 2-3 meters to the sides.
• Angle: 120 degrees.
• Sensitivity: Depends on ambient temperature, human body presence, and movement speed.

Diagram Description: A diagram illustrates the sensor's detection pattern, showing a wide, fan-shaped coverage area with indicated distances (2-3m, 5-7m) and the 120° angle.

Recommendations

1. Sensor range and sensitivity are as described above.
2. Please charge the night light before use.
3. Do not cover the sensor. Clean dust with soft cloths; avoid abrasive substances.
4. Do not place the device near heat-generating sources (e.g., radiators) or moisture-generating devices. Avoid direct sunlight and damp locations.
5. Charge the lamp only when necessary.
6. The indicator light is red when charging; no light indicates charging is complete.

Cautions and Warnings

General Use:

• For indoor use only.
• Use with caution near doors.
• (Note: The instruction to turn off power before bulb replacement is likely a generic safety note, as this is an LED product.)
• If in doubt, consult a qualified electrician.
• Do not place on inclined surfaces.
• For domestic use only. ?
• Do not dispose of with unsorted municipal waste. Electrical devices may release harmful substances into landfills, potentially contaminating soil and water and posing health risks. ❌

Product Specifics:

• If the cable is damaged, it must be replaced by the manufacturer or a qualified service technician to avoid hazards.
• The LED module is not replaceable.
• Do not disassemble the product. LED diodes can cause eye damage.

Technical Specifications

• Model: YLYD01YL
• Power: 0.25W
• Input: 5V
• Humidity: 0%-85% RH
• Temperature: -10°C to +40°C
• Standard: Q/QDYLK0002-2016
• Net Weight: 73g
• Dimensions: 73mm x 73mm x 34mm
• Lifespan: 25,000 hours

Precautions

1. Before charging, ensure the device contacts are clean.
2. Never leave the device unattended during use or charging.
3. Ensure the device can be quickly disconnected from the power source in an emergency.
4. Never expose the device to high temperatures.
5. Charge the device in a dry, well-ventilated area, away from flammable materials, maintaining at least 1 meter of clearance from other objects.
6. Never cover the device during charging.
7. Only use chargers, charging stations, and cables recommended and certified by the manufacturer.
8. Be aware that the device contains cells that are difficult to extinguish; keep a fire blanket accessible.

Battery Information

LI-ION Battery:

The device is equipped with a LI-ION (lithium-ion) battery, which ages over time due to its physical and chemical properties. The manufacturer specifies maximum operating time under optimal laboratory conditions with a new, fully charged battery. Actual battery life may vary. To maximize battery lifespan, avoid discharging below 3.18V or 15% capacity. Discharging below 2.5V can cause permanent damage, which is not covered by warranty. If the device is not used for over a month, charge the battery to 50% and check its charge level every two months. Store the battery and device in a dry place, away from sunlight and freezing temperatures.

LIPO Battery:

The device is equipped with a LI PO (lithium-polymer) battery, which ages over time due to its physical and chemical properties. The manufacturer specifies maximum operating time under optimal laboratory conditions with a new, fully charged battery. Actual battery life may vary. To maximize battery lifespan, avoid discharging below 3.5V or 5% capacity. Discharging below 3.2V can cause permanent damage, which is not covered by warranty. If the device is not used for over a month, charge the battery to 50% and check its charge level every two months. Store the battery and device in a dry place, away from sunlight and freezing temperatures.

Environmental Protection and Warranty

This document is a translation of the original user manual provided by the manufacturer.

Environmental Compliance:

The product is marked in accordance with the European Union directive on waste electrical and electronic equipment (WEEE). It must not be disposed of with municipal waste but should be collected and recycled separately. Proper disposal helps prevent potential negative consequences for the environment and human health. For detailed information on waste disposal, contact your local municipality, waste disposal facility, or the retailer where the product was purchased.

The product complies with EU directives concerning safety, health, and environmental protection.

Maintenance and Warranty:

Regular maintenance (cleaning) should be performed by the user or specialized service points at the user's expense. If the manual does not specify periodic maintenance, assess the product's physical condition at least weekly against its new state. If any difference is noted, take immediate maintenance (cleaning) or service steps. Failure to perform proper maintenance may lead to permanent product damage, for which the warranty provider is not liable.

Detailed warranty conditions are available on the distributor's/manufacturer's website: https://serwis.innpro.pl/gwarancja