Installation Instructions

Contents

1. General safety information
2. External dimensions of the appliance
3. Side-by-side assembly

General safety information

The manufacturer works constantly on the further development of all the types and models. Therefore please understand that we have to reserve the right to make design, equipment and technical modifications.

To get to know all the benefits of your new appliance, please read the information contained in these instructions carefully. The instructions apply to several models. Differences may occur. Text relating only to specific appliances is marked with an asterisk (*).

Instructions for action are marked with a ➔, the results of action are marked with a ▷.

The socket must be easily accessible so that the appliance can be quickly disconnected from the supply in an emergency. It must be outside the area of the rear of the appliance.

DANGER: Identifies a situation involving direct danger which, if not obviated, may result in death or severe bodily injury.

WARNING: Identifies a dangerous situation which, if not obviated, may result in death or severe bodily injury.

CAUTION: Identifies a dangerous situation which, if not obviated, may result in minor or medium bodily injury.

NOTICE: Identifies a dangerous situation which, if not obviated, may result in damage to property.

Note: Identifies useful information and tips.

External dimensions of the appliance

A diagram shows the external dimensions of the appliance with labels a through h. A table provides specific measurements for the SBS(es/bs) models.

Model | a [mm] | b [mm] | c [mm] | d [mm] | e [mm] | f [mm] | g [°] | h [mm]
SBS(es/bs) | 1210 | 1850 | 600 | 665 | 1185 | 1752 | 115 | 35
SBSes/bs | 84.. |

* If you are using wall spacers, add 15 mm to the dimensions.

With the door open, the dimensions apply to an opening angle of 115°. Distances vary depending on the opening angle.

Side-by-side assembly

Install the freezer or the appliance with freezer compartment on the left as viewed from the front. These appliances have a side-wall heating on the right-hand side to prevent the formation of condensation.

All the assembly components are supplied with the appliance. Fitting parts in the accessory kit.

Top front of the appliance:

Push both appliances together up to approx. 10 mm apart so that they stand flush at the front.

Line the appliances up with a spirit level on the top of the appliance.

Fig. 5: Tighten the outer adjustment feet. The appliances can be moved easier.

Fig. 6: Remove the existing covers. Before fitting the top bracket remove both earthing screws (14). Store the earthing screws safely. The screws are necessary for fitting the bracket as shown below.

Fig. 7: Slide the bracket (3) onto the pins with the spacer between the appliances. Screw the brackets in loosely alternately right and left with four screws (4) and the previously removed earthing screws (14).

If necessary, line the appliances up with a spirit level on the top of the appliance.

Bottom front of the appliance:

NOTICE

Risk of damage when moving the combined SBS appliance! The combined SBS appliance is heavy once assembled. The appliance may be dented by improper movement. Observe the information given on moving the appliance (see above).

Remove all protective film from the outside of the housing.

Top back of the appliance:

Fig. 8: Remove the existing covers. Slide the bracket (6) on with the spacer between the appliances and screw in loosely with the 4 screws (4). If necessary line the appliances up again. Now tighten the screws firmly at the top and bottom.

Fig. 9: Slide the bracket (7) onto the top of the appliance with the lugs and with the spacer between the appliances. Screw in firmly with the 2 screws (5).

Bottom back of the appliance:

Fig. 10: Slide the bracket (8) on once more with the slots over the retainer for the wall spacers. Screw in tightly with the 2 screws (5).

Fig. 11: NOTICE: Only drill through the metal plate. Drilling depth approx. 1mm. Pre-drill the screw holes with a 3 mm drill and deburr.

Fig. 12: Before fitting the top and front cover strips, push the two bars together over the whole length. The strips can be inserted more easily into the gap. Use a soft cloth to push the strips in to avoid dents in the surface of the cover strips. Press the strips into the gap carefully and evenly in order to achieve an optimum bond.

Fig. 13: On the top press the short cover strip (9) into the horizontal gap.

Fig. 14: On the front, press the long trim (10) into the vertical gap. Ensure that the strip rests on the connecting plate. Peel the protective film off the cover strip.*

Fig. 15: Snap the top cover (11) onto the still open gap between the two control panel trims. Make sure that the outer sides of the cover form a flush finish with the control panel trims.

Fig. 16: Place the bottom cover (12) onto the bracket from the front (1), slide it down (2) and snap it in at the bottom (3). To disassemble the cover, insert a screwdriver at the bottom on the side below the cover and release both lower hooks. The cover can swing out towards the top.

Connect the appliance to the fixed water connection according to the manual.

NOTICE

Risk of damage when moving the combined SBS appliance! The combined SBS appliance is heavy once assembled. The appliance may be dented by improper movement. Observe the information given on moving the appliance (see above).

Carefully slide the combination into the intended position.

If necessary, align the height with the height-adjustable feet.

Then support the door: Lower the adjustment feet on the mounting block until they rest on the floor then turn a further 90°.

The doors can be aligned in height with the aid of the outer, lower turn hinges:

Extend the threaded pin Fig. 17 (17) a little (by one turn at most!).

Fig. 18: In order to lift the door unscrew the mounting block (18) clockwise with the supplied open-end wrench (2). When delivered the mounting block is completely screwed in.

Tighten the threaded pin Fig. 17 (17) again to secure the bearing pin.

Connect the combination to the mains according to the manual.

Appliances with IceMakers: