DIGITUS Wireless HDMI Extender / Splitter Set (100 m, 1x4)
Quick Installation Guide
Model: DS-55346
1. Introduction
Experience ultimate flexibility and performance for the transfer of your Full HD AV signals with our wireless transfer system, which offers a range of up to 100 meters in a 1:1 connection with unobstructed view. Our system supports both Point-to-Point and Multicast (Point-to-Multipoint) transfers, which allows you the freedom of transferring your AV signal to multiple displays at the same time or connecting a single source with various target devices. With a maximum resolution of 1080p / 60 Hz, our system guarantees sharp and smooth reproduction of your content. You can also expand your system easily for up to 4 receiver units (DS-55347), to achieve video splitter functionality and share your HDMI signal on up to 4 displays. The transmission module features an additional HDMI output (loop-out) which enables you to connect an external monitor, while integrated IR transmission allows for convenient control of your source device directly from the output display (receiver unit). Our Plug & Play system does not require any additional software or driver installation and is ready for immediate use.
2. Main Features
- Wireless transfer of Full HD AV signals over a distance of up to 100 m (1:1 connection, unobstructed view)
- Supports Point-to-Point and Multicast (Point-to-Multipoint) transfer
- Transfer of HDMI signals in Full HD with max. resolution of 1080p / 60 Hz
- Expandable for up to 4 receiver units (DS-55347) and offers video splitter functionality with additional receivers
- Distribute your HDMI signal on up to 4 displays
- Additional HDMI output (loop-out) on transmitter module for connection to an external monitor
- IR transmission to control the source device from output display
- Plug & Play - no software or driver required
- HDMI 1.4, HDCP 1.3
3. Package Content
- 1x Transmitter unit
- 1x Receiver unit
- 2x Antenna
- 2x Power adapter, cable length: 1.2 m
- 2 x IR connection cable, 1.2 m
- 1x User manual
4. Technical Features
| Feature | Specification |
|---|---|
| Input Port | HDMI x 1 |
| Output Port | HDMI x 1, LOOP OUT x 1 |
| Wireless Extension Distance | 1 to 1 connection: up to 100m 1 to 2 connection: up to 75m 1 to 3 connection: up to 40m 1 to 4 connection: up to 25m |
| Signal Compressing Latency | 150-200ms |
| Wireless Extensions Distance (for 1080p) | 100m (330 feet) |
| Frequency Band Range | 5GHz |
| Wireless Standard | 802.11a |
| Vertical Frequency Range | 50/60Hz |
| Compress Formats | H.265 |
| IR Frequency Range | 20-60KHz |
| Progressive Resolutions (50&60Hz) | 480p, 576p, 720p, 1080p |
| Operating Temperature | 0°C to 50°C |
| Storage Humidity | 5% to 90% RH non-condensation |
| Power Supply | DC 5V |
| Power Consumption (Max) | TX: 3W, RX: 1.5W |
| Dimension (LxWxH) | 115x60x18mm |
| Net Weight | TX: 172g, RX: 170g |
| Material | Metal |
5. Panel Description
Transmitter (TX) Unit
Front Panel:
- 1. HDMI IN: HDMI Input Port
- 4. LOOP OUT: HDMI Loop Out Port for Local View
- 7. IR OUT: IR Signal Output Port
- 3. DC/5V: DC 5V Input Port
Rear Panel:
- 5. RESET: Long Press 10 Seconds to Reset, Short Click to Match the Sender and Receiver
- 8. Power LED: Indicates power status
- 9. Link: No Connection: Keep Lighting on; Get Connection: Flash Quickly
- 10. Status: No Video Signal: Flash Slowly; Get Video Signal: Flash Quickly
Receiver (RX) Unit
Front Panel:
- 2. HDMI OUT: HDMI Output Port
- 6. IR IN: IR Signal Input Port
- 3. DC/5V: DC 5V Input Port
Rear Panel:
- 5. RESET: Long Press 10 Seconds to Reset, Short Click to Match the Sender and Receiver
- 8. Power LED: Indicates power status
- 9. Link: No Connection: Keep Lighting on; Get Connection: Flash Quickly
- 10. Status: No Video Signal: Flash Slowly; Get Video Signal: Flash Quickly
Image Description: Diagrams of the front and rear panels of the Transmitter (TX) and Receiver (RX) units, showing numbered ports and status indicators.
6. Supported Formats
- Simple Plug and Play, no software installation required
- Support 5GHz single frequency wireless A/V transmission
- Wireless extension of HDMI up to 100 meters (330 feet) with no obstruction
- Compliant with HDCP1.3
- Support highest video resolution 1080p
- Support Point-to-Point and Multicast transmission (up to 4 receivers)
- Support infrared remote to control source device from the display side
- Support uncompressed audio such as LPCM
- Support audio sampling rate up to 48 KHz
7. Connection Diagram
A diagram illustrates a 'Point-to-Multipoint Connection'. A 'Source' device (Quelle) is connected via HDMI to a DS-55346 (TX) Transmitter. The Transmitter sends a wireless signal (1080p/60Hz) to up to four DS-55347 (RX) Receivers (Empfänger). Each Receiver is connected via HDMI Cable to a 'TV/Monitor' displaying 1080p/60Hz. The diagram also labels 'Point-to-Multipoint Connection' and 'HDMI Cable'.
8. How to set up 1 to 4 connections
- Step 1: Install antennas for Sender & Receiver. Image Description: An image shows the Sender and Receiver units with their antennas installed, ready for setup.
- Step 2: By pressing "RESET" button first, the Sender will be connected with power until the Status Led flashes frequently. Then it will take approximately 7s from power on to enter matching mode. The 1.2.3 or 4 Receivers follow the same steps as the Sender. Image Description: An image displays the Sender and Receiver units, highlighting the 'RESET' button (labeled '1') and the status LEDs (labeled '2').
- Step 3: When the Status Led of the Receiver (1,2,3,4) flashes frequently, it means it entered the matching mode. Image Description: An image shows the Receiver unit with its status LED flashing.
- Step 4: Use HDMI male to male cable (Not Included) to match the signal. Image Description: An image shows a black HDMI male-to-male cable.
- Step 5: Connect “HDMI IN” of the Sender and “HDMI OUT" of the Receiver (1,2,3,4) with HDMI cable. Image Description: An image shows the rear panels of the Sender and Receiver units. The 'HDMI IN' port on the Sender and the 'HDMI OUT' port on the Receiver are circled, indicating where to connect the HDMI cable.
- Step 6: When the Status Led of the Receiver (1,2,3,4) is permanently on, it means the signal matching is successfully. Image Description: An image shows the Receiver unit with its status LED permanently on, indicating successful signal matching.
- Step 7: Make sure the Sender and Receiver (1,2,3,4) are not powered. Image Description: An image shows the Sender and Receiver units. The text indicates to ensure both units are not powered during a specific step.
- Step 8: Connect power of the Sender and Receiver (1,2,3,4), then connect HDMI cable to the “INPUT” of the Sender to HDMI sourcing device and the "OUTPUT" of Sender (1,2,3,4) to the display or TV. Image Description: An image shows the Sender and Receiver units with power adapters and HDMI cables connected to their respective ports ('HDMI IN' on Sender, 'HDMI OUT' on Receiver).
- Step 9: The display or TV will show “Searching TX" about 5s to 35s. Image Description: A black screen displays the text 'Searching TX' in white, indicating the status on the connected display during the setup process.
- Step 10: Matching successfully. This step confirms successful matching.
9. Troubleshooting
| Problems | Causes | Solutions |
|---|---|---|
| No picture after correct connection at one room | Maybe the sender and receiver have not yet matched the connection | Follow the matching steps to match the signal of the Sender and Receiver |
| No picture after correct connection at different room | The distance can't reach 100m due to the signal loss via passing through solid walls | When passing through a solid wall (thickness less than 30 cm), the signal loses 30% of the original signal and the distance is shorter than 70 m. When crossing two or more solid walls, the distance is shorter than 20 metres. Please select a shorter distance when crossing a solid wall. |
| The picture is not stable or the distance is shorter than the description | There may be some sources of interference in the same frequency band at 5GHz that affect the signal transmission of the extender. | Please move the device closer to the location where sources of interference with the same frequency band are located or remove the sources of interference. |
Disclaimer
Hereby ASSMANN Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
Manufacturer:
ASSMANN Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Website: www.assmann.com
Symbols Description: The page includes the CE mark, indicating conformity with European directives, and the WEEE symbol (crossed-out wheeled bin), indicating proper disposal of electronic waste.
ASSMANN Electronic GmbH | Lüdenscheid, Germany
