Plantronics Voyager Legend UC Bluetooth Headset

Basic Operations

Answer a call: Put on the headset, or tap the Call button, or say "answer" after the call is announced.

Reject a call: Press and hold the Call button for 2 seconds, or say "ignore" after the call is announced.

End a call: Tap the Call button.

Voice dial: Press and hold the Call button for 2 seconds, wait for the phone prompt, then say the name of a stored contact.

Mute microphone: Tap the Mute button. You will hear "mute on" confirmation. Tap again to unmute, hearing "mute off" confirmation.

Play/pause streaming audio: Press and hold the Play/pause button for 2 seconds.

Call back last call: Double-tap the Call button.

Adjust volume: Toggle the Volume button (+) or (-) during a call or while streaming audio.

1. Pair Mobile Phone and Call

Pair your mobile phone

1. Power on your headset. Tap the Voice button and say "Pair mode," or press and hold the Call button until you hear "Pairing." The headset LEDs will flash red and blue.
2. Activate Bluetooth® on your phone and set it to search for new devices.
3. Select "PLT_Legend" from the list of devices.
4. If prompted for a passcode, enter "0000." The LEDs will stop flashing, and you will hear "pairing successful." Some phones may ask to allow access to contacts for caller name announcements.
5. Make a test call from your mobile phone.
6. End the call by pressing the call button.

Pair another phone

1. Power on your headset and initiate pairing mode as described above.
2. Activate Bluetooth® on the new phone and search for devices.
3. Select "PLT_Legend."
4. Once successfully paired, LEDs stop flashing, and you will hear "pairing successful."

2. Connect PC and Call

Connect

1. Power on the headset.
2. Insert the Bluetooth USB adapter directly into your PC USB port. The LED will flash and then turn solid blue, indicating connection. You will hear "PC connected."
3. The USB adapter comes pre-paired with your headset.
4. Visit plantronics.com/software to load Plantronics Spokes software for advanced settings.
5. Check your PC audio settings:
• Windows 7: Control Panel > Sound > Playback tab. Set "Plantronics BT300" as the Default Communications Device. For streaming audio, also set it as the Default Audio Device (indicated by a green check mark). Repeat for the Recording tab.
• Windows XP: Control Panel > Sounds and Audio Devices > Audio tab. Set "Plantronics BT300" as the default device for Sound Playback and Sound Recording.
6. Place a call from your computer softphone. The Bluetooth USB adapter LED will flash blue during an active call.

To Re-pair your Bluetooth USB adapter

1. Power on the headset.
2. Remove the USB adapter.
3. Initiate pairing mode on the headset (as described in step 1 of "Pair your mobile phone").
4. Insert the Bluetooth USB adapter into your PC USB port. Once paired, LEDs stop flashing, and you will hear "PC connected."

3. Charge and Fit Headset

Three ways to charge your headset

Your headset has enough power for initial use, but can be charged at any time.

1. Align the magnetic snap-fit areas of the headset and charging device.
2. Connect the charging device to a USB wall charger or laptop. Charging takes approximately 90 minutes. LEDs turn off when fully charged.

Charging Options:

• USB cable to PC or USB wall charger
• Charge case to PC or USB wall charger (The charge case can recharge the headset twice on the go.)
• Charge stand to PC or USB wall charger

Fit your headset

Replace the eartip for a better fit:

1. Push in the eartip and rotate it left to unlock.
2. Align the new eartip into the slot.
3. Push in the eartip and rotate it right to lock it in place.

To wear the headset on your other ear, rotate the boom upwards, twist it around so the eartip is on the other side, then lower the boom.

4. Use and Reset Smart Sensors™

Use sensors

Smart Sensors react to wearing or removing the headset:

• Putting on headset: Answers incoming calls, transfers active calls from your phone, or resumes streaming audio.
• Taking off headset: Transfers active calls to your phone handset, pauses streaming audio, or locks the Call button to prevent accidental calls.

Try voice commands

Tap the Voice button, wait for the prompt, and say a command. Say "What can I say?" to hear the full list of available commands.

Reset sensors

If sensors are not working correctly, reset them:

1. While wearing the headset, tap the Call button to test sensors. A "talk time voice alert" means sensors are working. A tone indicates they need resetting.
2. To reset, charge your headset and place it on a flat, non-metallic surface for over 10 seconds.

NEED MORE HELP?

Technical support

plantronics.com/support

Online user guide

http://docs.plantronics.com/VoyagerLegendUC

FCC Regulatory Information

Declaration of Conformity: Plantronics, Inc. declares that the BT300 complies with Part 15 of the FCC Rules. Operation is subject to two conditions: this device may not cause harmful interference, and it must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits for an uncontrolled environment.

Industry Canada Regulatory Information

This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: this device may not cause interference, and it must accept any interference, including interference that may cause undesired operation. This equipment complies with IC radiation exposure limits for an uncontrolled environment.

Exposure to RF Radiation

The internal wireless radio operates within established radio frequency safety standards and recommendations. Independent studies have shown the wireless radio to be safe for consumer use.

Plantronics, Inc.
345 Encinal Street
Santa Cruz, CA 95060
United States

Model Numbers: Voyager Legend UC, BT300

Certifications: FCC, IC, Singapore IDA Standards DA101760, Australia Z302 N10687

© 2012 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics Voyager Legend, and QuickPair are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Plantronics, Inc. is under license. All other trademarks are the property of their respective owners.

Patents Pending