SEABORG 350

Features

• Gear stick
• Realistic foot pedals
• 8 action buttons
• Button programming

Requirements

• Console or PC with a USB port
• Windows® XP/Vista/7/8/10
• Microsoft® Xbox One, 360; Sony® PlayStation® 3, 4; Nintendo® Switch®

Package Content

• 1x wheel
• 1x foot pedals
• 1x mounting clamp
• 1x manual

Warranty

2 years limited manufacturer warranty

Specifications

Installation

PC

(Optional) Install driver.

Connect foot pedals connector (1) to socket in wheel (2).

Connect USB cable from wheel (4) to free USB port in PC.

Wheel is ready.

Nintendo Switch

PRO controller support must be activated in console settings for wheel to be recognized.

Plug wheel USB cable into Switch docking station free USB port (with console docked in). Alternatively, using TYPE-C adapter (not included) connect wheel and console directly.

Power-on console.

Wheel will start the automatic configuration of the connection. When it finishes, MODE LED will be solid lit.

Wheel is ready.

PlayStation 3

Plug wheel USB cable into free console USB port.

Power-on console.

Wheel will start the automatic configuration of the connection. When it finishes, MODE LED will be solid lit.

Wheel is ready.

PlayStation 4

Plug wheel USB cable into free console USB port.

Power-on console.

Connect wheel via USB cable* with PS4 controller**. Controller must be shut off. Controller connection is mandatory for wheel to work.

After connection is estabilished, LED indicator will lit.

Wheel is ready.

Xbox One / Xbox 360

Plug wheel USB cable into free console USB port.

Power-on console.

Connect wheel via USB cable* with X1/X360 controller**. Controller must be shut off. Controller connection is mandatory for wheel to work***.

After connection is estabilished, LED indicator will lit.

Wheel is ready.

* Cable is not included

** Original controller - although recommended - is not required. However, the producer does not guarantee that every 3rd party replacements will work and/or work correctly

*** A wired controller is required for X360 control

Button Mapping

PC - X-INPUT / D-INPUT

Configuration and Programming

Switching Between X-INPUT and D-INPUT Modes

To switch between X-Input and D-Input modes while the wheel is connected to PC, press and hold the HOME button for 3 seconds. The red LED will light up solid after the change is done.

Button Programming

Buttons YAXB, LB, LT, RB and RT (BASE buttons) can be assigned to the left and right gear shift paddles, throttle pedal, brake pedal, and gear up/down (FUNCTION buttons).

Press and hold the SHARE and OPTION buttons simultaneously for 3 seconds.

When the green LED in the center of the wheel lights up, release the buttons.

Press the desired FUNCTION button to which the BASE button function will be assigned. The green LED will start blinking.

Press the BASE button whose default function will be assigned to the FUNCTION button. The green LED will turn off.

Wheel Sensitivity Setup

Press and hold the SHARE and OPTION buttons simultaneously for 3 seconds.

When the green LED in the center of the wheel lights up, release the buttons.

Press the SHARE button again to check the current sensitivity level. There are 3 sensitivity levels: LED blinking slowly indicates the lowest sensitivity; LED blinking faster indicates medium sensitivity; LED blinking very fast indicates the highest sensitivity.

Press the SHARE button again to cycle through the sensitivity levels indicated by the green LED as described above. When the desired sensitivity level is chosen, confirm the selection by pressing the UP arrow on the wheel's D-PAD.

Programming Pedals and Paddles as the Y Axis

Press and hold the SHARE and OPTION buttons simultaneously for 3 seconds.

When the green LED in the center of the wheel lights up, release the buttons.

Press LEFT on the wheel's D-PAD. When the green LED turns off, the pedals are programmed as the Y-axis.

Press RIGHT on the wheel's D-PAD. When the green LED turns off, the gear paddles are programmed as the Y-axis.

Clear Single Button Assignment

Press and hold the SHARE and OPTION buttons simultaneously for 3 seconds.

When the green LED in the center of the wheel lights up, release the buttons.

Press the programmed button once. When the LED starts blinking, press the same button again. The default function is restored.

Clear All Buttons Assignment

Press and hold the SHARE and OPTION buttons simultaneously for 3 seconds.

When the green LED in the center of the wheel lights up, release the buttons.

Press and hold the OPTION button for 4 seconds. When the LED turns off, the default functions are restored.

Note: After restarting the device, all functions will revert to their default settings.

Safety and General Information

Safety Information

• Use as directed.
• Unauthorized repairs or dismantling the device will void the warranty and may cause product damage.
• Avoid hitting or friction with a hard object, as this may lead to surface abrasion or other hardware damage.
• Do not use the product in extreme temperatures (low/high), strong magnetic fields, or in damp or dusty environments.
• Do not drop, knock, or shake the device. Rough handling can break it.
• Slots and openings in the casing are for ventilation and should not be covered. Blocking the vents can cause the device to overheat.

General

The product is safe and conforms to EU requirements.

The product is manufactured in accordance with the European RoHS standard.

The WEEE symbol (crossed-out wheeled bin) indicates that this product must not be disposed of as household waste. Proper disposal of electrical and electronic equipment helps prevent harmful consequences for human health and the environment, resulting from potentially hazardous materials, mixtures, or components, as well as improper storage and processing. Separate collection of used equipment aids in recovering materials and components used in the device's manufacture. For detailed information regarding the recycling of this product, please contact your retailer or local authority.