Genesis Seaborg 200 Quick Installation Guide

This guide provides instructions for installing and using the Genesis Seaborg 200 racing wheel across various platforms.

Button Map

The following table details the button mapping for different platforms:

Features

• 270 / 900 degrees turn range
• Realistic foot pedals
• Gearshift paddles
• Button programming

Requirements

• Console or PC with a USB port
• Windows* XP/Vista/7/8/10
• Microsoft* Xbox* One, 360; Sony* PlayStation* 3, 4; Nintendo* Switch*

Package Content

• 1x wheel
• 1x foot pedals
• 2x mounting clamp
• 1x manual

Warranty

• 2 years limited manufacturer warranty

Specification

• Total buttons number: 15
• Action buttons: 10
• D-Pad: Yes, 8-direction
• Shifting paddles: Yes
• Foot pedals: Brake, throttle
• Input interface: X-input, D-input
• Communication: Wired
• Vibration: Yes
• Connector: USB
• Cable Length: 2 m
• Wheel dimensions: 35 x 29 x 28 cm
• Pedal dimensions: 31/18 x 23 x 14 cm

Installation

PC

• Connect foot pedals connector (1) to socket in wheel (2).
• Connect USB cable from wheel (4) to free USB port in PC.
• Wheel is ready.

PS3

• Plug wheel USB cable into free console USB port.
• Power-on console.
• Wheel will start the automatic configuration of the connection. When it finishes, LED will be solid lit.
• Wheel is ready.

XBOXI/360

• Plug wheel USB cable into free console USB port.
• Power-on console.
• Connect wheel via USB cable* with X1/X360 controller**. Controller must be shut off. Controller connection is mandatory for wheel to work***.
• After connection is established, LED indicator will lit.
• Wheel is ready.

SWITCH

• IMPORTANT! Before connecting wheel, please enable PRO controller support function in console settings.
• Plug wheel USB cable into Switch docking station free USB port (with console docked in). Alternatively, using TYPE-C adapter (not included) connect wheel and console directly.
• Power-on console.
• Wheel will start the automatic configuration of the connection. When it finishes, LED will be solid lit.
• Wheel is ready.

PS4

• Plug wheel USB cable into free console USB port.
• Power-on console.
• Connect wheel via USB cable* with PS4 controller**. Controller must be shut off. Controller connection is mandatory for wheel to work.
• After connection is established, LED indicator will lit.
• Wheel is ready.

PS2

• Cable is not included
• * Original controller - although recommended - is not required. However, the producer does not guarantee that every 3rd party replacement will work and/or work correctly
• *** A wired controller is required for X360 console

Switching Between X-Input and D-Input Modes

• To switch between X-Input and D-Input modes while wheel is connected to PC, press and hold MODE button for 3 seconds.
• Red LED will solid lit after change is done.

Turn Radius Set-up

• To change wheel max. turn radius, use mode switch. Left position of switch indicates 900-degree mode, right position 270-degree.

Button Programming

• Buttons ABXY, L1, L2, R1 and R2 (BASE buttons) can be assigned to L-paddle, R-paddle, throttle pedal, brake pedal, L3 and R3 (FUNCTION buttons).
• Press PROG button, red LED will start blinking quickly.
• Press desired FUNCTION button. Red LED will blink noticeably slower.
• Press desired BASE button. Its default function will be assigned to previously pressed FUNCTION button. Red LED will solid lit.

Clear Single Button Assignment

• Press PROG button, red LED will start blinking quickly.
• Press desired FUNCTION button. Red LED will blink noticeably slower.
• Press same FUNCTION button again. Red LED will solid lit and button function is restored.

Wheel Sensitivity Setup

• Press PROG button, red LED will start to blink.
• For high sensitivity, press Up Arrow on D-PAD.
• For medium sensitivity, press Left Arrow on D-PAD.
• For low sensitivity, press Down Arrow on D-PAD.

Customizing Turn Radius

To change effective* turn radius according to personal preference, do as follows:

• Change mode switch to 900 degrees position.
• Press PROG button, red LED will start to blink.
• Turn wheel to desired angle (min 60 degrees) and hold.
• Press OPTIONS button to confirm change.
• *Wheel real turn range is unaffected by this change, it only changes signal.

Programming Pedals and Paddles as the Y Axis

• Press PROG button, red LED will start blinking quickly.
• Press Right Arrow on D-PAD. Red LED will solid lit.

Clear All Buttons Assignment

• Press PROG button, red LED will start blinking quickly.
• Press and hold for 4 seconds OPTIONS button.

Safety Information

• Use as directed.
• Non-authorized repairs or taking the device to pieces make the warranty void and may cause the product damage.
• Avoid to hit or friction with a hard object, otherwise it will lead to grind surface or other hardware damage.
• Do not use the product in low and high temperatures, in strong magnetic fields and in the damp or dusty atmosphere.
• Do not drop, knock, or shake the device. Rough handling can break it.
• Slots and openings in the case are provided for ventilation and should not be obscured. Blocking the vents can cause overheating of the device.

General

• The product is safe, conforming to the EU requirements.
• The product is made in accordance with RoHS European standard.
• The WEEE symbol (the crossed-out wheeled bin) indicates that this product is not home waste. Appropriate waste management aids in avoiding consequences which are harmful for people and environment and result from dangerous materials used in the device, as well as improper storage and processing. Segregated household waste collection aids recycle materials and components of which the device was made. In order to get detailed information about recycling this product please contact your retailer or a local authority.

For product and support information, please visit www.genesis-zone.com.