SCS Sentinel CodeAccess A - Keypad User Manual

Description

Content / Dimensions

The CodeAccess A keypad is a compact access control device. Its dimensions are:

• Height: 9.7 cm
• Width: 7.5 cm
• Depth: 2.1 cm

The kit includes:

• CodeAccess A Keypad
• Manual
• Cables
• Screws and wall plugs (Visserie)

Wiring / Installing

Installing

Follow these steps for installation:

1. Mount the backplate on the wall.
2. Connect the wires according to the wiring diagram.
3. Attach the keypad to the backplate.
4. For a better seal, apply silicone to the top and the two sides of the keypad.

Wiring Diagram

To gate automation

Connections:

• DO: GREEN (NOT USED)
• D1: WHITE (NOT USED)
• ALARM: (No color specified)
• OPEN: YELLOW (EXIT BUTTON)
• D_IN: (No color specified)
• +12V: RED (+)
• GND: BLACK (-)
• NO: BLUE
• COM: PURPLE (TO GATE AUTOMATION)
• NC: ORANGE (NOT USED)

To strike/electric lock

Connections:

• DO: GREEN (NOT USED)
• D1: WHITE (NOT USED)
• ALARM: (No color specified)
• OPEN: YELLOW (EXIT BUTTON)
• D_IN: (No color specified)
• +12V: RED (+)
• GND: BLACK (-)
• NO: BLUE (STRIKE / ELECTRIC LOCK)
• COM: PURPLE
• NC: ORANGE (NOT USED)

To reset the factory default

1. Disconnect power from the unit.
2. Press and hold the '#' key while powering the unit back up.
3. On hearing two "BIP" sounds, release the '#' key. The system is now back to factory settings.

Note: Only installer data is restored; user data will not be affected.

Indications

Using

Fast programming

Programming a code

1. Enter programming mode: Press '*' then the default master code (999999) then '#'.
2. Add a code: Enter user number (1-100), then '#', then the 4-digit user code (except 1234), then '#'.
3. Exit programming mode: Press '*' then '#'.

Programming a badge

1. Enter programming mode: Press '*' then the default master code (999999) then '#'.
2. Add a badge: Press '1' then '#'.
3. Present the badge(s) to the keypad. Each programmed badge will automatically increment the user number.
4. Exit programming mode: Press '*' then '#'.

Door opening

• Through user code: Enter the programmed user code, then press '#'.
• Through badge: Present the programmed badge to the keypad.

Detailed Programming Guide

User Settings

Note: The master user must be logged in to perform the following programming.

Setting the working mode:

• 30 #: Entry is by card only
• 31 #: Entry is by card and PIN together
• 32 #: Entry is by either card or PIN (default)

To add a user in either card or PIN mode (mode 32 #):

• To add a PIN user: 1 User ID number # PIN #. The ID number is between 1 & 100. The PIN is any four digits between 0000 & 9999 (1234 is reserved). Users can be added continuously.
• To delete a PIN user: 2 User ID number #. Users can be deleted continuously.
• To change the PIN of a PIN user: (This step must be done outside programming mode) * ID number # Old PIN # New PIN # New PIN #

To add a card user:

• Method 1 (Fastest): 1 Read card #. Cards can be added continuously without exiting programming mode.
• Method 2 (User ID Allocation): 1 ID number # Read card #. User can be added continuously without exiting programming mode. Only one user ID can be allocated to a single card.

To delete a card user:

• By card: 2 Read Card #. Users can be deleted continuously without exiting programming mode.
• By user ID: 2 User ID #. This option can be used when a user has lost their card.

To add a card and PIN user (mode 31 #):

Add the card as for a card user. Press '*' to exit programming mode. Then allocate the card a PIN as follows: * Read card 1234 # PIN # PIN #

To change a PIN in card and PIN mode:

• Method 1 (Outside programming mode): * Read Card Old PIN # New PIN # New PIN #
• Method 2 (Outside programming mode): * ID number # Old PIN # New PIN # New PIN #

To delete a Card and PIN user:

Simply delete the card.

To add and delete a card user in card mode (30 #):

The operation is the same as adding and deleting a card user in mode 32 #.

TO DELETE ALL USERS

2 0000 #. Note that this is a dangerous option, so use with care.

TO UNLOCK THE DOOR

• For a PIN: Enter the PIN then press '#'.
• For a card User: Read card.
• For a card and PIN user: Read card then enter PIN '#'.

Door settings

RELAY OUTPUT DELAY TIME

Changing the master code

For security reasons, it is recommended to change the master code from the default.

Technical Features

• Voltage: 12V DC +/-10%
• Badge reading distance: 0-3 cm
• Active current: < 60mA
• Stand-by current: 25±5mA
• Lock load output: 3A max
• Operating temperature: -35°C ~ 60°C
• Relay output delay time: Adjustable
• Possible wiring connections: electric lock, gate automation, exit button
• Backlight keys
• 100 users, supports badge, PIN, badge + PIN
• Full programming from the keypad
• Can be used as a stand-alone keypad
• The keypad can be used to remove the lost badge number, thoroughly eliminate the hidden safety trouble
• Adjustable Door Output time, Alarm time, Door Open time
• Fast operating speed
• Lock output current short circuit protection
• Indicator light and buzzer
• Frequency: 125 kHz
• Maximum transmitted power: 2.82 mW

Warranty

Warranty 2 years

The invoice will be required as proof of purchase date. Please keep it during the warranty period. Carefully keep the barcode and the proof of purchase, as this will be necessary to claim warranty.

Warnings

• Maintain a minimum distance of 10 cm around the device for sufficient ventilation.
• Keep matches, candles, and flames away from the device.
• Product functionality can be influenced by strong electromagnetic interference.
• This equipment is intended for private consumer use only.
• The appliance should not be exposed to dripping or splashing water; no objects filled with liquids, such as vases, should be placed near the appliance.
• Do not use in a tropical climate.
• Connect all the parts before switching on the power.
• Do not cause any impact on the elements as their electronics are fragile.
• When installing the product, keep the packaging out of reach of children and animals. It is a source of potential danger.
• This appliance is not a toy. It is not designed to be used by children.

Before any maintenance, disconnect the appliance from the main power supply. Do not clean the product with solvents, abrasive or corrosive substances. Use only a soft cloth. Do not spray anything on the appliance.

Make sure that your appliance is properly maintained and regularly checked in order to detect any sign of wear. Do not use it if a repair or adjustment is needed. Always call on qualified personnel.

Do not throw batteries or out-of-order products with household waste (garbage). The dangerous substances they may contain can harm health or the environment. Ask your retailer to take back these products or use the selective collection of garbage proposed by your city.