TaiMei MD04 Mirror Installation and User's Guide
Brand: TaiMei
Model: MD04
Important Safety Instructions
SAVE THESE INSTRUCTIONS
Read all instructions before using.
DANGER: To reduce the risk of electric shock:
- Always unplug this furnishing from the electrical outlet before cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons.
- Unplug from outlet before putting on or taking off parts.
- Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
- Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
- Keep the cord away from heated surfaces.
- Never operate the furnishing with the air openings blocked. Keep the air openings free of hair, and the like.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- To disconnect, turn all controls to the off position, then remove plug from outlet.
- WARNING: Risk of Injury - Keep children away from extended foot support (or other similar parts).
- WARNING: Risk of Electric Shock - Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
- For loading, always put heavier items at the bottom and not near the top in order to help prevent the possibility of the furnishing tipping over.
- WARNING: Risk of injury to persons - Do not place video equipment such as televisions or computer monitors on the product.
- WARNING: Risk of Injury to Persons - Do not use this furnishing to support video equipment such as televisions or computer monitors.
Grounding Instructions
This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.
Before Beginning
Carefully read the instructions before beginning the installation.
DANGER: To avoid the risk of electrocution, please turn off the main electrical power before starting the installation.
It is strongly recommended that a professional electrician perform this installation.
It is advisable to wear safety glasses throughout the installation process.
This installation requires a minimum of two people.
This product is for wall mounting only.
Maintenance
Never use scouring pads, abrasive materials, strong bleach, or sharp instruments on metal components or glass. An occasional wipe-down with a mild soap diluted in water is all that is needed to keep the mirror and aluminum parts looking new. Test products on a small inconspicuous surface prior to use.
Tools and Materials Required
Tools:
- Drill / Taladro
- Drill Bits / Brocas para taladro
- Level / Nivel
- Tape Measure / Cinta métrica
- Pencil / Lápiz
Hardware:
- 1 1/2" Screw / Tornillo (x2)
- Wall Plug / Enchufe de pared (x2)
- Wire Connector / Conector eléctrico (x3)
- Mounting Bracket / Soporte de fijación (x2)
Mirror Installation
Placement / Ubicación
Select the desired position of the mirror. Level and mark the location.
Diagram Description: Shows a mirror outline with a dashed rectangle indicating the placement area.
Support Location / Ubicación del Soporte
Mark the drilling locations to ensure that the markings are level.
Diagram Description: Shows the back of the mirror with mounting points marked. Dimensions indicate 5 inches from each side and 2 5/8 inches from the top edge for the mounting bracket positions.
Install Mounting Bracket / Instalar Soporte de Montaje
Using a drill, create holes, fill them with the supplied plugs, and install the mounting bracket.
For drywall more than 10-12mm in thickness, please make sure to use specified drywall anchors for installation. For drywall with thickness less than 10-12mm, please make sure to install the brackets on the stud.
Diagram Description: Step-by-step illustration showing drilling holes in the wall, inserting wall plugs, and attaching the mounting bracket using a 1 1/2" screw.
Connecting Electrical Wiring / Conexión de Cableado Eléctrico
WARNING / AVISO ⚠️
Diagram Description: Illustrates the electrical connections from the wall to the mirror. Wires are labeled LIVE (usually black), NEUTRAL (usually white), and GROUND (usually green). The diagram shows these wires connecting to corresponding terminals on the mirror.
Please Note: The colors referenced in the diagram above are based on conventional standards and may differ between households. If there is any confusion about how these should be connected, please seek the assistance of a licensed professional electrician. Electric shock, fire hazards, and death are possible consequences of poor wiring, for none of which FOCA will be held liable.
Final Placement
Place the mirror against the wall and slide it down as shown in the illustration.
Diagram Description: Shows the mirror being placed against the wall and then slid downwards to engage with the mounted brackets.
User's Guide / Guía del Usuario
Caution / Precaución
Touch button will be functional only after 3 seconds of power-up.
Touch Operation
Short Touch / Toque breve (<1s):
Diagram Description: Illustrates a finger touching the button.
1x Touch: Turns the LED light ON / ENCENDIDO ?
1x Touch: Turns the LED light OFF / APAGADO ?
Operate the LED luminaire after it is switched on.
Diagram Description: Sequence of hand gestures and LED light changes.
Short Touch / Toque breve (<1s):
Diagram Description: Sequence showing multiple short touches to adjust brightness.
1x Touch: 100% brightness ?
1x Touch: 60% brightness ?
1x Touch: 30% brightness ?
1x Touch: 5% brightness ?
Diagram Description: Sequence showing a long touch to activate/deactivate the defogger.
Long Touch / Toque prolongado (>1s):
1x Touch: Turns LED ON / ENCENDIDO and activates Defogger / Desempañador ❄️☀️
1x Touch: Turns LED OFF / APAGADO and deactivates Defogger / Desempañador ❄️☀️
Diagram Description: Further illustration of long touch operations for brightness adjustment and defogger.
Long Touch / Toque prolongado (>1s):
Diagram Description: Sequence showing long touches to cycle through brightness levels (e.g., 100% to 5% and back).
Diagram Description: Sequence showing long touches to activate/deactivate the defogger, with a "STOP / PARAR" indicator.
Caution / Precaución
Power lines come out of the wall from the shaded area, which is 4 inches from the mirror's edge and 12 inches from the line of buttons.
Diagram Description: Shows the mirror outline with a shaded area indicating where power lines exit the wall. Dimensions show the shaded area is 4 inches from the mirror's edges and 12 inches from the button line.
